Search Documents

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

The impact of smoothing on the definition of ore and waste boundaries using linear estimation and conditional simulation methods is discussed. The nature of transfer functions is examined including their ability to incorporate categorical data (e.g. a dominant lithology code). An Ore Block Optimization (OBO) transfer function is presented that provides a clear guide for the mining geologist. Advantages are seen in defining stockpile cut-off grades and meeting production targets such as maximizing head grade, maximizing ore tonnes or minimizing ore loss or dilution. Each of these scenarios impacts on mine profitability and grade control.

Jan 1, 1999

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By A. Fred Gelding

Introduction In preparing this paper considerable time was spent attempting to find some upbeat data about the mining industry, so those of us in the field could feel somewhat better about future prospects. Much to my regret, I failed to uncover substantial evidence that our near-term or, for that matter, our long-term opportunities appear all that bright in North America. That is certainly not the kind of assessment anyone likes to hear or accept as even a possibility. Those remarks may, on the surface, appear far too pessimistic. This industry will experience a recovery and most likely will see conditions begin to improve later this year or early next. The kind and degree of recovery, however, will more than likely differ from those experienced in the past. Fundamental Changes Clearly, the fundamentals on a world scale of our business have undergone important changes. In recognizing these fundamental changes, mining authorities believe productivity advances are needed to change the direction mining has taken in recent years. The really tough question is whether increases in productivity will be enough to change the course of events that has dominated the mining sector for the past decade. Before one can provide an honest answer, an appraisal of what has and is happening now is necessary. Here are some changes and events that have taken place that effect domestic mining and will probably continue: • Mineral-rich lesser developed countries (LDCs) in Africa, South America, and Asia-Pacific have reached a point where they have developed the needed mining infrastructure to not only produce at a high rate, but in many instances, at a lower cost than fully developed countries. Just as importantly, these countries, even if they do not enjoy lower costs, will produce for world export with government subsidies because min¬ing products are key in obtaining badly needed foreign exchange. • These producing countries also have the distance advantage of lower labor, environmental, and other important regulatory costs. If that were not enough, these same countries have minerals with considerably higher grade ore and, in some cases, much lower cost accessibility. • Exporting North American commodities is impaired by a dollar that continues to strengthen against other important currencies around the world. There are other impediments to overcome, but these represent some of the realities our industry faces. Can those obstacles be overcome through improving productivity? In the past, this industry has offset the impact of these events to a sizeable degree through innovations of mining techniques, equipment and processes, and by increasing the size of its individual operations to reduce costs. Will further enhancements along these lines be enough to alter this changing balance in the future? While there is no answer, it is apparent that if we do not mount a full-scale assault in some key areas, our prospects will not be encouraging. Productivity improvements throughout the entire chain of the mining industry most certainly rates as a high priority. Every link in that chain from mine planning, equipment selections, and transportation considerations needs to be examined and reexamined to assure the lowest effective cost is developed. Quality, while oftentimes costing a little more initially, is still the most cost effective purchasing decision to make. Regulations Another area of concern is regulations, be they environmental or those that dictate what must or must not be done in running our business. Certainly, I do not suggest that we not protect our environment. However, there is an acceptable balance that has, over

Jan 11, 1983

"One of the major issues that the Rare Earth Elements Mining Industry has to deal with is the legislation vacuum that exists in many countries around the world. Among these, are countries which have long history and tradition in mining. In many cases the lack of direct legislation for REE mine management as well as for other potentially polluting industries can be a barrier to sustainable development. Moreover, the case of lax legislation in China has led to environmental pollution problems and extended smuggling of rare earth elements. This paper looks into the current regulatory status on the mining of REEs, identifies the loopholes and suggests some elements for a new global legislation framework for sustainable development in the REE mining industry. The setting of this regulatory framework will be in line with the present and future challenges of the rare earths market as well as with the policy strategies that are defined internationally. The aim of such a legislative framework will be to strengthen the global rare earth elements supply chain, appease social concerns and ensure the preservation and conservation of the environment. INTRODUCTION The general public received their first introduction to rare earth elements (REEs) in 2010, when the previously inconspicuous commodities became the subjects of front-page headlines. It was when China created a furore in global high-tech markets after imposing an embargo on Japan following a minor marine dispute (Barakos et al. 2015b). Soon enough the Chinese embargo was extended on REE export restrictions all over the world and thus aroused concerns to many countries over potential supply disruptions. The world had suddenly realized that these wonder materials underpin products that they care about. Governmental and industry executives, policymakers and material scientists voiced concerns and conducted numerous reports stating the situation and the risks of a supply crisis. The price spike of 2011 intensified the crisis and the public turmoil, yet the drama did not last for long as the prices declined significantly in 2012. Nevertheless, the world was nonplussed by the fact that China has the total control of the market with more or less the 90% of the global production. More potential entrants became interested, thus initiating an exploration boom during the recent years that has resulted in a significant increase in known global REE reserves that could have potentials for exploitation."

Jan 1, 2016

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various complex ore deposits and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides and other phases for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay & Gorain, 2014; Chattopadhyay et al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2017

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By F. Baldini, M. S. Borges

"The proposed method emphasizes the optimization of waste management with regard to the exploitation of raw materials incorporated in the remains of industry, as well as the economics of natural resources as an environmental impact assessment. This system [tool] allows: (a) the conversion of an environmental liability into an asset by finding a line of appropriate research for each type of waste and the development of new materials applicable to other industries, (b) the performance of internal control of the waste generated (production, storage, final destination) as well as legal conformity.Objectives:1.1 General objective:To design a collaborative system for socio-environmental management of industrial waste.1.2 Specific objective:Develop evidence of concepts;Evaluate the deployment of the inventory of waste in an industry;Enable the conversion of an environmental liability into an asset by finding a line of research appropriate to the waste: a case study;Evaluate the environmental legislation in the legal mechanisms that influence company decisions.IntroductionThe global economy is undergoing major changes, among these changes; it should be highlighted those related to technological progress and environmental quality.While the industrialized countries and higher levels of economic growth dominate modem technology, developing countries are identified by a different growth pattern, using the annual growth rate of Gross Domestic Product per capita [3, 18].Growth is when the GDP grows, in percent, over the previous year. Development, on the other hand, is when the countries change their technologies and improve their internal structure. Thus, the growth considers the accumulation of wealth, while the development is concerned with the distribution of wealth, improvement of the quality oflife and environmental quality [3, 18].As the UNESCO report shows (1999), the biggest problem is between consumption and development, what is produced and the end that is given to the product. Therefore, product and by-product have equal importance in the quantity produced [29].On one hand there is a positive relationship between indicators of economic growth and technological progress, however, on the other hand, these transformations are a paradox, confirmed by the dramatic use of environmental resources and the lack of technologies for recycling of industrial scrap."

Jan 1, 2011

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifications, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and viability of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 1, 1984

By V. A. Chanturiya, T. N. Matveeva, N. K. Gromova, T. A. Ivanova

"The research is aimed at solving the problem of increasing the extraction of gold from refractory ores, which are the main source of growth in gold production in the next decades. The purpose of the research is the development and scientific substantiation of the reagent modes for flotation extracting of gold from refractory ores using eco-friendly low-cost herbal modifiers (HM), providing increase in gold recovery and quality of gold concentrates. In the course of research laboratory techniques for the preparation of experimental samples of HM were developed, which included the sequence of operations of grinding Heraclium leaves and stems grinding, 2-stages extraction at a temperature of 50-60 °C, short-term ultrasonic treatment, filtration and subsequent unification of extracts. According to the developed method, the experimental samples of HM and conducted research were tested to analyze their sorption and flotation activity related to the extraction of gold from refractory gold ores.New data on adsorption and flotation properties of Heraclium stems and leaves extracts (HSE) in selective flotation of Au-sulfide minerals were obtained using UV-spectroscopy, scanning electronic and laser microscopy and atomic force microscopy. The dimensions and shapes of adsorbed hydrophilic films of herbal reagents were identified and mechanism of formation of stable insoluble compounds on the surface of minerals in flotation was explained.Research flotation tests carried out on samples of refractory gold ore of one of Russia deposits showed the possibility of effective use of herbal modifiers to improve qualitative and quantitative indicators of enrichment compared with the standard reagent regime. New reagent modes, using herbal modifiers in an amount of 5 to 10 ml of the extract (300 - 600 g / t, respectively) improves the quality of the concentrate: gold content attains 14.7 g / t, 1.34 times higher than in the baseline experiment and provides a gain of 3.13% extraction.The developed reagent regime with herbal modifiers is the author's original design, patented (patent of the Russian Federation) and have no analogues in the world of mineral processing. (Application number 2015116125 from 04.28.2015, ""The method of flotation separation of sulfide minerals using herbal modifier"", Russia). Actual application of new plant extracts as modifiers in flotation of sulfide minerals is the possibility of replacing of highly toxic chemical compounds by environmentally safe substances of plant origin. Implementation of the developed methods of extracting gold from refractory minerals with herbal modifiers will help to improve gold recovery at 3-5% and the quality concentrate of not less than 1.2 times, leading to higher productivity and a reduction of the negative man-made effects on the environment ."

Jan 1, 2016

By Anil Kumar

In underground mine production units that employ discrete-vehicle face haulage, feeders are used in the belt network so that vehicles can unload rapidly without transmitting to the conveyor network the high material flow rates that result from rapid unloading. They prevent production bottlenecks at the face, while reducing capacity requirements for downstream materials handling equipment. Similarly, surge bins may be installed at intermediate locations in the network to smooth flows from a number of upstream sources, thereby reducing downstream belt capacity requirements. This paper introduces new stochastic process models to temporally describe loading patterns from unit operations and techniques for computing the probability of various fill levels for the feeder or surge bin. These results may be used to analyze the effect of alternative bin or feeder capacities and discharge rates on the performance and costs of the materials handling system.

Jan 1, 1994

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By J Jardine

An improved ground support method for development intersections, wide spans and stope brows was implemented at Kanmantoo mine. The method uses a jumbo to simultaneously drill and install self-drilling anchors (SDAs) to depths from 4.5 m to 7.0 m. Resin is subsequently pumped into each SDA using a specially designed integrated tool carrier basket, with plating occurring within 10 mins due to rapid resin cure. This methodology means that SDAs can be installed rapidly due to reduced process steps and wait times with reduced hazards to personnel. Cablebolts are used extensively in underground mines to reinforce the ground in wide spans, such as at intersections and stope brows. The flexible cablebolt tendon allows for a long, continuous and high-capacity reinforcing element to be inserted into the rock. A common cablebolt installation practice at Australian underground mines that do not utilise a mechanised cable bolter, is for cablebolt holes to be drilled by a jumbo or longhole rig, hand installation and grouting by a service crew, then plate tensioning following a grout curing wait time of typically 12 to 24 hours. This process involves multiple separate labour-intensive work processes and results in reduced availability of priority headings. This paper discusses the development history of vertical SDA use in wide spans at Kanmantoo mine. The installation process is fully described, including aspects such as reliable in-hole coupling of SDAs, resin selection and pumping aspects. A cost benefit assessment, and a case for ground stability are presented to compare cablebolt use to SDAs in development intersections.

Mar 29, 2023

By Enrui Dai, Weibing Chen, Bin Yang, Wenhui Ma, Haisheng Fang, Hui Wang

LiMn0.8Fe0.2PO4/C composite was prepared by an improved solid-state method and the effect of calcination temperature on properties of the obtained materials was investigated. The results showed that increasing calcination temperature from 600 to 700 oC improved the performance of the LiMn0.8Fe0.2PO4/C due to enhanced crystallinity and increased conductivity, but further increase in calcination temperature to 800 oC led to degraded performance due to particle growth and decrease in porosity. Therefore, the LiMn0.8Fe0.2PO4/C composite prepared at 700 oC exhibited the best electrochemical performance, and could deliver a high capacity of 152 mAh g−1 at 0.1 C, 147 mAh g−1 at 1 C and 114 mAh g−1 at 10 C. In addition, the performance of the LiMn0.8Fe0.2PO4/C and LiMn0.8Fe0.19Mg0.01PO4/C was compared when they were obtained at the optimum calcination temperature.

Jan 1, 2015

By V. A. Temeng, M. Owusu-Tweneboah, K. Awuah-Offei

The mining industry has long recognized the value of dispatch systems in open pit mines as they reduce load and haul costs. Over the years, researchers have proposed many dispatch systems with various limitations and advantages. The simplest dispatch algorithms are the so called 1-truck-for-N-shovels dispatch strategy. These algorithms are limited by the fact that their objective functions do not consider all the objectives of a mine and cannot be applied to all possible truck-shovel configurations. They are also myopic in nature. However, they are simple and computationally efficient and do not require occasional updates of the upper stage problem as required in multi-stage dispatch algorithms. In this work, an agent-based truck dispatch algorithm that conceptualizes trucks as intelligent agents that make autonomous dispatching decisions to maximize their utility is proposed. The advantages of this algorithm includes utility functions that encapsulate all of management’s objectives and agent’s with broad situational awareness. They are also more suitable for autonomous trucks. We evaluate the new algorithm against a simple 1-truck-for-N-shovels dispatch strategies using discrete event simulation. The simulation results show that the new utility function has significant advantages over 1-truck-for-N-shovels inspired utility functions. Future work will incorporate adaptive behavior into the model via reinforcement learning algorithm. INTRODUCTION In an attempt to optimize truck shovel operations in open pit mines in order to reduce the cost of haulage operation, which according to (Alarie and Gamache, 2002) is estimated to be about 50-60% of the total cost of mining, several effective and efficient strategies have been developed. Optimizing truck haulage systems in an open pit mine is one of the greatest challenges of mining engineering and has been the subject of many research projects. It is important that haulage systems are designed to be efficient, in order to minimise haulage cost, improve profitability and increase the total mine value. Although optimizing the number of trucks required in the operation of open pit mines can help reduce the cost, an effective and efficient truck dispatching system add value by ensuring that the available trucks are used efficiently. With truck dispatching systems, the trucks are normally dispatched between the crusher and dumping station (e.g. waste dumps and stockpiles), and the shovels in order to maximize the total output, obtain grades targets, reduce fuel consumptions and other objectives. Truck dispatching, which can have one or more objectives, is typically subjected to certain operational constraints such as truck and shovel capacities, empty and loaded trucks speed, among others. The problems associated with truck dispatching was first mentioned by Dantzig and Ramser (1959) after they made an attempt to determine the optimum routes of a fleet of delivery trucks between bulk terminals and a service stations. The problem occurs in several industrial systems besides mining (Alarie and Gamache, 2002; Gendreau et al., 2006; Rego and Roucariol, 1995). The dispatching problem, also referred in literature as the vehicle routing problem, has seen a number of modifications and extensions with Bertsimas and Ryzin (1991) presenting a dynamic and stochastic vehicle routing problem, and Ralphs et al. (2003) also adding to the original concept, the concept of vehicle capacity routing.

Jan 1, 2019

By E. A. Thiers

The causes of structural changes in the markets for high technology alloying metals are discussed in terms of technological, economic, and financial trends. Recent market imbalances have affected producers in developed and developing countries differently. Possible response strategies for suppliers in the two types of countries are examined that may alleviate future market imbalances.

Jan 1, 1988