Search Documents

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By M E. Karmis

Traditional coal mining planning seldom considers key æsustainability factorsÆ such as: societal impacts in the area; jobs (both created and lost); dislocation of towns and residences; impact on neighbouring communities and individuals; infrastructure concerns; post-mining land use (except when limited by law or other factors); habitat disruption and reconstruction; long-term economic impacts in the community; and net long-term community benefit. This paper presents a systems engineering approach based on the premise that systems can only be optimised if all factors are considered at one time. In theory, coal mine designs can be optimised for return on investment, environmental protection and sustainability. Using this approach, the permitting process may be quicker and less costly, relationships with neighbours, communities, environmental groups may be improved, the mining industry may be seen as a positive for the short-term and long-term and the mining industry may increase profits. This paper discusses geographic information system (GIS) tools that may be used to incorporate ecological and other sustainable development concerns into models of coal mine sustainability performance. Along with coal production cost and value information obtained from past and present coal mining operations, GIS data are used to develop mathematical cost and equation models. By analysis of on-the-ground data, the parameters to be included in these models are identified, the relationships between these parameters quantified and the models developed. The paper also discusses the next phases of the work to be completed once the data is obtained and the models are adjusted and validated. At that time, site-specific information will be input into the models and the approach to mining a particular property evaluated and optimised for financial rate-of-return and other desired outcomes, such as preservation or enhancement of sustainability values. Finally, the paper will examine how this approach can be combined with traditional mining engineering considerations in order to develop an optimised mine plan for a specific mining property.

Jan 1, 2009

By Michaela Böberl

State of the art sinter coolers are working based on the cross flow cooling principle. Thus, only a part of the thermal energy can be used for heat recovery application. The other part of the cooling air is brought unused to the environment. Furthermore, environmental regulation regarding dust emission and intelligent usage of exergy are getting stronger. Therefore, Primetals Technologies developed sinter coolers based on the counter flow principle. The cooling air passes the sinter bed in counter-flow direction enabling a direct heat transfer from the hot sinter to the air. The exhaust gas temperature can be maximized by using the total heat of the hot sinter. Due to the possible usage of the total exhaust gas amount, diffusive dust emission is reduced to zero. Two types of counter flow coolers are in the portfolio of Primetals Technologies. One type is based on a stationary shaft, in which the hot sinter is charged. The flow of the hot sinter is in vertical direction from top to bottom, in counter direction than the cooling air. The second type is a circular hopper cooler. The hot sinter is charged on top of a moving bed. At the bottom of the bed the sinter is discharged. The cooling air flows also from the bottom to the top, following the counter flow principle. Depending on the requirements, one of the two counter flow cooler types can be chosen for optimized and efficient cooling of hot sinter..

Oct 30, 2017

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963

By Arvind Thekdi, Cynthia Belt2

"Waste heat from industrial operations in metals industry represents 20% to 50% of the total energy used in most manufacturing plants. Reduction and recovery of waste heat offers the most attractive and cost effective method of reducing energy intensity for an industrial plant to meet corporate energy saving goals. It is possible to reduce or recover 30% to 60% of the available waste heat by using conventional and readily available technologies. Projects to reduce or recovery waste heat may offer less than 3 years payback to as short as a few months. This paper presents information on most commonly used methods for waste heat reduction and recovery in the metals industry operations. It describes the methods and use of analysis tools that would allow a user to estimate energy savings, CO2 or GHG reduction potential, and economic benefit and includes appropriate case histories.Waste Heat SourcesSources of waste heat abound with the metals industry. While the overall quantity of energy is high, the sources are distributed throughout a plant. The largest source within the metals industry is within furnace exhaust / flue gases. This includes the high temperature gases from burners in process heating such melting, calcining, and sintering operations. It also includes lower temperature gases from heat treat, dryers, and heaters. Lower temperatures are also found after post processed hot gases. This could include heat left after heat exchangers, regenerative systems, thermal oxidizers, and emission control systems. Other hot gases include air used in direct and indirect cooling.While waste heat in form of exhaust gases is readily recognized, waste heat can also be found within liquids and solids. Waste heat within liquids includes things such as cooling water, heated wash water, and blow down water. Solids can be hot product at discharge after processing or reactions are complete. Indeed, not only is energy wasted in the hot metal that slowly air-cools, but additional energy may be used in providing air or water-cooling to increase the speed of cooling. Other waste heat sources are not as apparent and include things like hot surfaces, steam leaks, boiler blow down water, etc. Table 1 and Figure 1 show several major sources along with the temperature range and characteristics of the source."

Jan 1, 2011

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don't assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it's straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it's very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By Y. Mitsuda, Y. Kayanuma, T. H. Okabe, M. Miyake

A new process to recover platinum group metals (PGMs) from automotive catalyst scrap using metal vapor was developed. To improve the efficiency of the acid dissolution process of PGMs, metal vapor of reactive elements such as magnesium or calcium were contacted with spent automotive catalyst. It was expected that metal vapor would react with metal selectively and form intermetallic compounds. The specimen of the spent catalyst was treated at 1173 K for 3 h, and it was then dissolved in aqua regia for 1 h to recover PGMs. After the reactive metal treatment, 88% of Pt, 81% of Pd, and 72% of Rh in the catalyst scrap was dissolved, while only 77% of Pt, 69% of Pd, and 38% of Rh was dissolved from untreated scraps.

Jan 1, 2004

By W. C. Joughin

A risk evaluation model has been developed that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment, which is described in Part I (Joughin et al., 2011b). Part II presents the validation of the risk evaluation model. Underground mapping of joints and rockfalls was carried out to provide data for field calibration of the model. This survey was limited to small rockfalls, due to the relatively short period of mapping. Therefore the model was also correlated with rockfall and rockfall injury data collected by mine personnel. The analyses showed that the model provides a reasonable estimate of the expected frequency and size of rockfalls and the frequency of rockfall injuries, but further work is required to enhance the model. Three case studies are presented, which show the benefits of improved support systems from both economic and safety perspectives. This work has demonstrated that the risk evaluation model and the software developed are immediately useful, but further work is required to develop and improve the tools.

Jan 1, 2012

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War I1 has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

By D van der Spuy, T Kewe, K Keet, N Moffatt, A P. Paine

The Blue Cube Mineral Quantifier Inline (MQi) instrument uses reflective light spectroscopy and advanced chemometrics to measure mineral or elemental grade in a slurry line. The instrument takes scans continuously and sends data to the DCS or PLC control system.Controlling the concentrate grades on a flotation circuit using low-frequency measurements can be difficult or impossible, especially on a circuit that has fast process dynamics. The ability to rapidly measure changes in grade makes it possible to continuously manipulate the flotation circuit operating parameters such as level, airflow and reagent addition set points to optimise plant performance throughout changing conditions.At Barrick’s Porgera mine in Papua New Guinea the flotation circuit feeds sulfide concentrate slurry to a pressure oxidation circuit. In order to maximise gold recovery in the flotation plant and increase performance in the pressure oxidation process, there is a stringent requirement to maintain a stable and optimum sulfur grade. The gold recovery is directly affected by the sulfur grade as most of the gold at Porgera is submicroscopic and associated with the sulfides (disseminated?pyrite).Porgera considered various points in the flotation circuit for installing Blue Cube analysers. This was part of a plant upgrade to improve process control. Due to budget constraints it was decided to initially only install one Blue Cube analyser on the final concentrate stream of the flotation circuit measuring sulfur, sulfides, gold and particle size. The accuracy of the calibration results were very good for all these properties. The sulfur measurement was used in an advanced control system to optimise and stabilise the grade. The paper presents comparisons between mineral grades determined using analytical laboratory analyses and the online Blue Cube data measurements, as well as benefits achieved by measuring grade online. An analysis of the plant data before and after installation of the Blue Cube and the advanced process control upgrade indicate that the flotation recovery increased by 1.98 per cent.CITATION:Kewe, T, Moffatt, N, Strobos, P, van der Spuy, D, Paine, A P and Keet, K, 2014. Evaluation of the Blue Cube MQi slurry analyser for application in an advanced control system for the optimisation of a gold sulfide flotation circuit, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 357–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M. R. Khalesi, S. Arfania

"Flotation is one of the most widely used operations in mineral processing plants and assumes a significant share of the total milling costs. The purpose of this paper is to introduce a new set of capital and operating cost models for major flotation machines based on the application of single (SRA) and multiple regression analysis (MRA). Thirty-seven major flotation machines were analysed for this purpose. Depending on the machinery type, different technical variables such as diameter, required air flow rate, required floor space, cell volume, required air pressure, and power were considered as predictor variables, individually (in SRA) or simultaneously (in MRA). Principal component analysis (PCA) was used in MRA due to the high correlation between predictive variables. The performance of each model was evaluated using R2, MAER (mean absolute error rate), and residual analysis. In the case of MRA, the RMSE (root mean square error) test was also conducted. Maximum obtained MAER of 13.5% and minimum R2 of 0.86 indicated that these models could be applied as credible tools in estimation of capital and operating costs of flotation machines for design and feasibility studies.IntroductionMineral processing is a vital part of mining projects and mainly involves comminution, sizing, concentration, extractive metallurgical processes, and dewatering. Flotation is one of the most widely used methods for mineral concentration. Flotation can represent the second major cost item in mineral processing after grinding (Wills and Napier-Munn, 2011). Accordingly, it is a main concern of mining project managers to select and optimize flotation circuits in order to decrease costs and increase productivity. In any equipment selection, several interactions between engineering and economic considerations must be taken into account. Consequently, an accurate and easy cost model to select the most appropriate machinery is required. Moreover, cost models could be used in flow sheet simulations applied in design and optimization. Models of unit operations built into the simulators could be improved by linking the equipment cost models (Khalesi et al., 2015)."

Jan 1, 2017

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

It?s a pleasure to be with you in Vancouver today to reinforce the good work you and your companies do to develop and operationalize new technology as a lever to improve operational performance and reduce our impact on the environment in absolute terms. Although I will use the work we do at Shell to reinforce this perspective, the principles apply to all of us in this industry regardless of whether you are a producer or supplier. I?d like to help demystify the future of Canada?s oil sands based on Shell?s view of global energy developments, including forecasted demand. One of the incontrovertible truths of this era of global energy defines change as an unchangeable law of progress. Another tells us that the art of progress is to preserve order amid change and to preserve change amid order. These axioms help frame the increasingly public debate about the future of Canada?s oil sands. I hope to illustrate how Shell?s commitment and investments create positive progress that embraces change amid order in the oil sands. I?m going to spend a little time today to focus the spotlight on the future of the oil sands to help demystify Canada?s hydrocarbon energy future. To do that, I?ll identify the features of our future energy security, including three hard truths about global energy that drive Shell?s business imperatives. Then, it?s instructive to examine Canadians? current consciousness about oil sands sustainability.

Oct 1, 2009

By T. P. Oxford, G. Y. Onoda, E. D. Whitney

Disposal of phosphatic clay waste slurry has been a problem since the advent of hydraulic processing of phosphate rock in Florida. Alternatives to the present practice of storing slimes behind earthen dikes have been earnestly sought for more than a quarter of a century. Seepage dewatering is a promising technique intended to increase waste clay solids content to a level sufficiently high to permit clay disposal in mine cuts, in lieu of above-grade impoundment. An experimental array of vertical seepage columns containing mine tailings sand was constructed. Significant improvement in waste clay dewatering relative to that occurring in a control test was observed when approximately 1800 m3 of waste clay was disposed of in the presence of the seepage aids.

Jan 1, 1983

By Worotnicki G, Tillmann V. H

Past experience with fully bonded cable dowels placed as a means of reinforcement in highly stressed crop pillars at the New Broken Hill Consolidated Limited (NBHC) mine indicated such support was not fully effective. Typically overbreak of the crown occurred leaving long lengths of cables hanging from the back stripped of grout and rock with the potential load carrying capacity of the cables not having been fully utilised. This mode of behaviour had been observed in the cable dowelled crowns of three longhole open stopes (EROS) mined to the No. 12 level at NBHC. A system of support with improved mechanism of load transfer from rock to cable and capable of full utilisation of cable strength was proposed for the crown pillars of future Stopes.

Jan 1, 1983

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012