Search Documents

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By M. Murillo, J. Botín

"Mining has always played a key role in the improvement of the quality of life, but also, it has been a source of environmental and social conflict. Despite the great progress in social responsibility and sustainability experienced in recent decades, the public image of mining remains low and mining projects and operations must face growing difficulties and demands, which results in increasing capital and operating costs. In practice, the objective of a mining company is to create value for its shareholders and therefore, the best approach to Sustainability would be to foster those drivers aligning sustainability and shareholders value, this is, the “Business Case for Sustainability” (BCS). Only under this assumption, convergence of corporate strategy and sustainability may be assured. This paper discusses partial results of a Research Project being carried out at the Catholic University of Chile, aiming to develop a social and economic model for the effective integration of the values of sustainable development in the strategy of mining companies and their stakeholders. INTRODUCTION Mining is fundamental for the wellbeing of our everyday life. But as important as these benefits are for humanity, the mining Industry has had negative environmental and social impacts. For these reasons, a closer relationship between “Sustainable Development and Mining” is more necessary than ever. The Brundtland definition of Sustainable development does not have a clear relationship with mining, but it provides the context. Under a strict interpretation of the Bruntlandt definition, stating that “Sustainable development is development that meets the needs of the present without compromising the ability of future generations to meet their own needs” [10], mining would not be sustainable because the minerals are non-renewable resources. However, this research focuses on how mining can contribute to the sustainable development in the territories where the projects take place. In other words, this research follows the publication titled “Berlin II Guidelines for Mining and Sustainable Development” [9], which stated that “A mining project that is developed, operated and closed in an environmentally and socially acceptable manner could contribute to sustainable development. Critical to this goal is ensuring that benefits of the project are employed to develop the region in a way that will survive long after the mine is closed”. The potential conflicts between mining stakeholders arises from the interpretation of the concept “developing, operating and closing a project in an environmentally and socially acceptable manner”, and the impact on the economic objectives of mining companies. Nevertheless, the ability of mining companies to control new demands and expectations of stakeholders has threatened the implementation and continuity of their projects and operations. To deal with these issues this research analyses the “Business Case for Sustainability” (BCS). It refers to the process leading to a business and social-economic environment whereby shareholders value may only be optimum under a business strategy which fully integrates the values of sustainability. In the model proposed, the Business Case will start when the benefits are higher than the costs. Benefits not only associated with efficient use of resources, also benefits associated with avoiding difficulties to continue with the mining projects such as strikes, heavy penalties, loss of investment, and so on."

Jan 1, 2016

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

By A. B. Parsons

AT the outset, the authors of this paper desire to file a disclaimer and an, explanation. They have no inside information from occult sources; neither of them feigns clairvoyant powers in the slightest degree. It is true that they have indicated on be graphs an approximate trend for the consumption of seven important mineral commodities up to the year 1954. At best this is a risky business; the figures do not pretend to be any- thing more than reasoned conjectures that are predicated on an attempt to evaluate some of the more obvious of the many factors that are likely to have a bearing on the future.

Jan 1, 1937

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By O. M. Johnson

Barite and bentonite are the two principal components of drilling fluid systems used in the petroleum industry for oil and gas well drilling with rotary-type rigs. Approximately 87 percent of the world's annual production of barite is used in drilling applications. Of the worldwide production of bentonite, an estimated 30 percent is used. The drilling fluid, or drilling mud, to which barite and bentonite are added, performs five distinct functions: Lubrication-The liquid phase of the drilling mud lubricates the drill bit, preventing premature failure of the cutting edges and bearings. it also helps to soften the formation being drilled. Cuttings Removal-A mud system must be able to carry rock cuttings broken loose by the bit up to the surface where they can be removed by mechanical or chemical methods. The fluid's ability to perform this function depends upon maintaining a proper balance between the rate of circulation of the fluid and the colloidal properties required to entrain the cuttings in the mud to prevent their settling to the bottom of the hole. Hole Stability-The pressure exerted by the mud against the wall of the bore hole prevents the collapse of the uncased portions of the hole. Downhole Information-The fluid characteristics of the mud should be such that good cuttings samples, cores and electric logs may be obtained to help evaluate a well's productive zones and potential. Control Oil, Gas and Water Flows-It is essential that a drilling fluid offset any pressure from naturally occurring formation fluids in order to prevent a potentially wasteful and dangerous blowout.

Jan 1, 1980

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By A Horeth, E Duggan, B Versiani, A Gooch

Iron ore screening plant productivity is strongly affected by the performance of the shuttle operation, with the control system robustness and associated strategies having a direct impact on utilisation and throughput rates. A number of aspects intrinsic to the methods and technologies traditionally applied on the motion control of shuttles are often observed to decrease the efficiency of the ore distribution process across multiple screening modules, which ultimately impacts the plant’s production. Those include the number of operational scenarios that are unmanaged by conventional discrete control logics which may intermittently lead to undesired events, such as ‘high level alarms’ and ‘low level interlocks’ in the screening bins. This outcome usually demands excessive manual intervention by Control Room Operators. A Reinforcement Learning (RL) Artificial Intelligence (AI) solution was deployed to control the motion operation of the scalping and products screening shuttles in an iron ore handling plant. The RL algorithm was trained in advance to handle multiple operational scenarios and generate optimised outputs. In nominal operation, the shuttles are moved in a modulating and highly predictive fashion over the whole range of safely reachable bins. When the need occurs, the AI control agent deviates from that modulation behaviour, limiting its travel range or moving to other groups or clusters of available bins by employing ‘bin jumping’ or ‘ore break’ strategies. The RL platform capabilities include the ability to learn in real time to account for and auto-adapt to new operational patterns and process changes whilst applying improved strategies for shuttle dwelling times, target setting and speed control. The deployed Reinforcement Learning AI solution has better managed the existing challenges associated with the shuttle operation and control, and resulted in a more efficient ore delivery process, superior operations stability and increased production rates.

Nov 8, 2021

By Technische Universität Braunschweig, K. Saksl, J. Furste, P. Eschenbacher, F. Brunke, D. Wolter, M. Kohnke, C. Siemers, J. Kiese, M. Schlemminger

"In general, titanium alloys combine outstanding mechanical properties with corrosion resistance and biocompatibility and are, therefore, used in many challenging applications. Nevertheless, for special products, well-tailored properties are required which might not be achievable by a specific design so that new or modified alloys are needed. In this overview paper, alloy development strategies performed at the Institute for Materials of the Technische Universitat Braunschweig are discussed at different examples, namely, (1) oxidation-resistant, microstructural-stabilized and cold-workable alloys for exhaust applications, (2) aluminum- and vanadium-free, medium-strength and cold-workable alloys for implants and osteosynthesis applications and (3) free-machining alloys by the addition of particles with low melting points for non-safety critical light-weight constructions to replace heavier steels, e.g. in automotive applications. A special focus is set on the alloy development techniques and the analyses carried out to achieve well-balanced properties by the optimization of the alloy compositions. INTRODUCTIONTitanium belongs to the allotropic metals and can therefore exist in two different equilibrium lattice modifications. Pure titanium crystallizes at 1668°C in a body centered cubic (bcc) structure called ?- titanium which at 882°C transforms to a hexagonal close packed structure (hcp), the a-titanium. A martensitic ?-to-a-transformation is possible at large cooling rates. This thermally induced hexagonal martensite is called the a'-phase. The transformation temperature named ?-transus-temperature (T ?) can be influenced by alloying elements (Peters & Leyens, 2002).For titanium alloy production typical alloying elements are aluminum (Al) and oxygen (O), both a-stabilizers shifting the ?-transus temperature to higher temperatures, whereas tin (Sn) and zirconium (Zr) only show a limited influence on the ?-transus temperature. The ?-stabilizing elements are subdivided into two groups: Niobium (Nb), molybdenum (Mo) and vanadium (V) stabilize the ?-phase between the melting point and room temperature and are therefore called isomorphous -stabilizers. Elements like copper (Cu), iron (Fe) or silicon (Si) also stabilize the ?-phase to lower temperatures but undergo a eutectoid reaction during cooling. ?-titanium then dissociates to a-titanium and an intermetallic compound. Consequently, these elements are called eutectoid ?-stabilizers (Boyer, Welsh & Collings, 1994)."

Jan 1, 2016

By N. El-Kaddah, J. W. McKelliget

"A mathematical model for the analysis and design of hybrid plasma reactors for advanced materials synthesis is presented. The model is based upon a solution of the electromagnetic vector potential equation and is capable of predicting the two-dimensional velocity, temperature, and electromagnetic fields as well as the reaction kinetics inside the reactor for any axi-symmetric coil configuration. The model is used as a computer aided design tool for the design of hybrid plasma reactors consisting of a conventional DC torch augmented by an RF induction coil and it is demonstrated that the hybrid system possesses superior characteristics for materials synthesis over conventional DC or RF systems. The coupling between the RF and DC components is found to affect both the temperature field and the flow field and to have a significant effect on the reaction kinetics and on materials recovery. The model is used to study the thermal decomposition of silicon tetrachloride as a function of reactor design and operating parameters and it is demonstrated that through a CAD approach it is possible to significantly improve the operation of materials synthesis systems.IntroductionIn recent years there has been growing interest in the use of the inductively coupled plasma for chemical synthesis as a way of meeting the increasing demand for high quality, high performance materials for use in critical applications/l/. Although the basic feasibility of this approach has been demonstrated in the laboratory/2,3/ there still exists a number of operational problems that adversely affect system performance for some applications. In particular, the recirculation and back flow effects that arise from the electromagnetic forces in the plasma can result in the repulsion of the reactants from the hot plasma core and their subsequent deposition on the walls of the reactor. Another operational problem arises from the fact that the energy dissipated in the plasma has to compensate for the heat losses to the environment by conduction, convection, and radiation in order to maintain the ionization of the plasma and, hence, the stability of the plasma may be affected by the presence of the reactants and their products."

Jan 1, 1988

By AIME AIME

READERS of a technical paper, or the audience if the paper is presented orally, judge the paper on several counts. The September 1940 issue of MINING AND METALLURGY contained an excellent short article by S. Marion Tucker en- titled "Are You Going to Present a Paper," which considered the general subject of presentation. In it Dr. Tucker referred to the large number of poorly prepared and badly delivered papers that are presented annually before the large number of technical and other societies that meet regularly, and he stressed the point that good delivery, length of paper, content, and composition are of great importance. All of Dr. Tucker's points were well taken; however, good illustrations are equally important in explaining certain phases of some papers.

Jan 1, 1941

By G. I. Voiloshnikov, V. E. Dementyev

"One of the most important advances in the world gold metallurgy is the introduction of adsorption technologies for processing of ores and concentrates. «Adsorbent-In-Pulp» process allows to eliminate pulp filtration that is especially important during processing of clay and slime bearing ores. “Adsorbent-In-Leach” process is one of the ways for processing of preg-robbing (carbonaceous) products. High efficiency, increased metals recovery, decrease in capital and operational costs, possibility of easy control and adjustment are the advantages of adsorption processes. Anion-exchange resins and activated carbons are used as adsorbents. This paper presents Irgiredmet experience on gold adsorption technology using both adsorbents (RIP, RIL, CIP, CIL processes). It includes results of long-term studies of different theoretical and practical issues of adsorption processes. Irgiredmet started development of ion exchange technology (RIP, RIL) in 1964. Laboratory and pilot plant tests were conducted to develop process design criteria for 15 RIP plants of the former USSR. During this test work a great number of newly synthesized resins including strong- and medium-base resins was studied, different types of adsorption feed (ores and concentrates) were tested; some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption for silver gold ore, improved flowsheet for gold elution and resin regeneration, designs of technological equipment for adsorption, elution, electrowinning processes including pulsation columns, electrowinning cells etc. were developed. Irgiredmet took part in commissioning of practically all RIP plants in the former USSR. Due to its efforts RIP process became to be the standard technology. Last Irgiredmet RIP projects include the development of adsorption technology using medium-base resin for the three mines owned by GC Petropavlovsk (Amur region, Russia). The complex of the testworks on activated carbon gold adsorption technology including the search of prospective activated carbons; study on gold adsorption mechanism; development, testing and introduction of process flowsheets and the equipment for their realization was conducted. The original gold elution process was developed. The developed CIP technology was firstly introduced at Lebedinsky gold plant (Yakutia). Now carbon adsorption technology is widely used at Russian gold mines as CIP, CIL, CIC processes. The most relevant example of CIP introduction is Svetlinsky gold plant (Ural, Russia) with capacity 8 Mt of ore/ year."

Jan 1, 2018

By A G. L Pratt

Inclined troughed belt conveyors are more frequently being selected from a range of alternatives, which include shafts and trucks for ore haulage in underground mass mining projects. Belt conveyor haulage systems are being operated with lifts exceeding those normally associated with truck haulage systems and approaching the limits of shaft haulage systems. A belt conveyor haulage system, in this context, incorporates subsystems for: crushing,tramp detection and removal, andhaulage. This paper presents details of recent inclined troughed belt conveyor systems for underground mining operations, and explores the application of inclined troughed belt conveyors for the increasing demands of future underground mass mining projects.

Jan 1, 2008

By H. Kinilakodi

The authors previously developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the safe performance index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the health and safety risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency or the U.S. Mine Safety and Health Administration (MSHA) in recognizing and addressing emerging problems with actions that may have been able to predict high-risk conditions, the fatality and/or other serious injuries. The approach would have given extra scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By H. Matsuda, T. Iwashita, H. Awata, H. Liwei, D. Hirabayashi, Y. Saito, S. Ozawa, Y. Goto

"The present study is concerned with investigating the effect of chemical treatment on enhancing the HCl absorption capacities of coal burnt ash and slag. It was found that the HCl absorption capacity of coal burnt ash discharged from fluidized bed combustor was improved by hydration with water and 5% polyethylene glycol solution. This phenomenon was based on an increase of the specific surface area of treated coal burnt ash. The HCl absorption capacity of hydrated ash with polyethylene glycol solution was almost equivalent to that of standard CaO and Ca(OH)2. In particular, the specific surface area of hydrated ash with polyethylene glycol solution was found to be 19 m2/g, which was more than over eight times larger than that of raw sample. Hydrated slag treated with lON sodium hydroxide solution also showed high HCl absorption capacity, with highly improved surface area. It was found that the absorption capacity of slag for HCl depended on the treatment time, showing the maximum absorption capacity for 12 hours of hydration treatment.IntroductionA large amount of coal burnt ash, slag and dust are discharged from such industrial processes as coal combustion and metal refinery etc., and it becomes an serious problem to recover and diminish these solid wastes because of the shortage of dump sites and subsequent metal elution to the environment. Figure 1 shows the present situation of reutilization of coal burnt ash and slag in Japan [1,2]. It is shown in this figure that these solid wastes are recycled as materials in the fields of earthwork, agriculture and forestry etc. A part of these solid wastes, however, is still dumped to landfill. To decrease this dumped amount, the development of environmentally friendly reutilization technique for these solid wastes is of great importance."

Jan 1, 2000