Search Documents

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By A. L. Mular

Steady-state material balances calculated from data measured at various locations around process units are useful for many purposes, such as metallurgical accounting, on-line control, and the development of mathematical models. Often it is possible to calculate material balances by several independent procedures when excess measurement information, i.e., redundant data, is available. Clearly, if the data were collected without measurement errors, a theoretical condition never found in practice, all material balances calculated from redundant data would be in agreement. The real situation is that error exists in practical measurements, so that the results of material balances determined from available optional procedures differ. Consequently, best fit computational procedures to improve the material balances by taking measurement errors into account have been formulated. Such procedures can be used also to judge whether measurements are grossly in error due to either faulty observations or defective data sensing devices. A variety of mathematical techniques are available which serve to adjust raw data. The adjusted data permit mass balancing that does not depend on the computational method. To illustrate the need for an adjustment procedure, Table 1 shows a raw data set acquired around the Brenda Mines Ltd. No. 4 grinding circuit shown schematically in Fig. 1. At least seven optional ways to calculate a circulating load ratio may be employed. These are shown in Table 2 where, depending upon the calculation [ ]

Jan 1, 1979

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By Darrell Wilder

The Trenton Water Treatment Facility in Trenton, New Jersey, is expanding to upgrade existing facilities and to meet the increasing demands of the public. The facility sits uncomfortably between the northern bank of the Delaware River and Route 29, a busy traffic corridor. Flooding along this bank of the river occurs frequently and disrupts traffic along Route 29. The expansion plans for the facility call for several large clarifying tanks on a mat foundation covering an area of about 100 x 350 ft. The original design was to remove and replace up to 20 ft of existing fill and soft materials. Due to the close proximity to the existing structures and the Delaware River, it would be necessary to use sheet piles and tiebacks to support the proposed excavation, as well as the existing structures. The solution adopted consisted of the installation of vibro-replacement stone columns to improve the in situ soils and eliminate the need for excavation and replacement. This approach was tremendously successful. It mitigated the significant risk of flooding of the excavation, and provided a cost-effective alternative to mitigate settlement of the proposed tanks on the poor soft subgrade soils. This paper presents the details of the criteria for selection and design of the stone columns, and the process followed for installation of the stone columns and for verification of the level of soil improvement achieved. It also includes a back analysis of the results of a large scale, 10- by 10-foot plate load test performed on a group of stone columns using numerical procedures and recommendations for design and construction.

Jan 1, 2008

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By C. Flores

The most common experimental approach of studying one variable at a time while holding all others constant is extremely inefficient. Use of statistical methods enables engineers and scientists to obtain meaningful information with the fewest experiments, reducing cost and wasted effort. In particular, the Taguchi method can be more efficient than traditional full factorial experiment designs, as it can study more variables with fewer nuts, and it is more robust against process "noise." Taguchi designs are also simple to formulate and the results can be analyzed by simple PC spreadsheets. The role and benefits of using the Taguchi method in experiments to develop and optimize processes is discussed.

Jan 1, 1998

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976

By Donald J. Frendzel

The post-World War II expansion of the Soviet petroleum industry has established the U.S.S.R. as a major oil-producing nation and has led to Russian reentry into the international petroleum trade. The rapid growth of Soviet petroleum production will allow the U.S.S.R. to displace Venezuela as the world's second largest oil-producer in 1960 and to narrow further the gap between Soviet and U.S. crude-oil production. U.S.S.R. crude oil output was only a tenth of U.S. production in 1946, but it will be more than a third at the end of 1960 and more than half in 1965. The Soviet Seven-Year Plan (1959-65) for oil provides for substantial increases in petroleum production, refining, storage, and distribution facilities. Crude oil production and primary distillation capacity are to double, considerable storage capacity is planned, and pipelines for crude oil and petroleum products are to increase threefold. According to the Soviets, the initial phases of this plan (1959 and 1960) have been completed successfully. However, this progress has been achieved with difficulty.

Jan 1, 1961

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

"The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation are just a few of the processes that are largely influenced by the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the importance of surface wettability, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In the present study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.Through the use of an inert adhesive and an inert macroscopic surface as a support, it is illustrated that precise measurements of particle wettability are obtainable under suboptimal or ‘shop floor’ conditions. The measurement of the maximum external meniscus height formed between a test liquid and a particlecoated rod is employed to estimate phenomenological contact angles on particles ranging form a few nanometers to several hundred microns in size."

Jan 1, 2003

By Dinesh Goyal

Industrial fly ash from (electro static precipitator) was mixed with soil at different levels on v/v basis for raising of pulpwood tree species. In field trials conducted on degraded soils increase in the plant growth of Eucalyptus tereticornis, Acacia auriculiformis and Casuarina equisetifolia by 10 %, was observed during the initial six months after plantation at 18-24% (v/v) fly ash concentration which was at par with chemical fertilizer treatment. Level of As, Se and Mo in flyash was 6.2, 3.6 and 4.0 ppm respectively. The radioactivity analyses 40K, soil and 28 fly ash showed that the activity levels of gamma emitting radionuclides K, Ra, Ac were within the permissible limits and mixing of fly ash with soil at tested concentration would have no deleterious effects. Available Co, Cr, Ni and Cd in rhizospheric soils were below detection limit. Fly ash at 10-20 % level (v/v) was also found to be a good potting mix material in forestry nurseries in terms of improving biomass production by 20 %, when tested in nursery seedlings of Eucalyptus tereticornis. Nursery addition of fly ash in soil decreased soil dehydrogenase activity and the soil bacterial population was negatively affected. These results indicate that use of fly ash in forestry sector involving nursery and plantations as a soil amendment agent upto 10-20 % v/v is a gainful utilisation of fly ash.

Jan 1, 2002

By Philip W. Holland

The U.S. Bureau of Mines has developed an improved method for determining dissolved helium in water in the concentration range of 4.0 x 10-8 to 270 X 10-8 cm3 He (STP)/cm3 H2O. The method is a modification of a previously reported method that was developed for analrzing surface and subsurface waters in geochemical survey work. Water samples are collected in SOD-cm stainless steel cylinders, and the dissolved gases in a sample are extracted into an evacuated cylinder of equal volume. After addition of 30 psig of nitrogen containing less than 2 ppb helium to the extracted gases, the resulting mixture is analyzed for helium using a helium-tuned mass spectrometer. The helium content of the water sample is determined from an empirical calibration that is established by analyzing standard solutions of helium in water. The accuracy of the method is ±7 pct for helium-in-water concentrations above 10 x 10-8 cm3 He (STP)/cm3 H2O.

Jan 1, 1989

By H. R. Babitzke, H. Kato, M. D. Carver

A number of columbium and tantalum alloys were investigated to determine their suitability for use at elevated temperatures . Columbium-vanadium , tantalum-vanadium , and tantalum-hafnium alloys , and also columbium- 10 wt pct titanium alloys modified with additions of 0.1 to 2 mole pct ZrO2 , TiO2 , ZrB₂ , TiB , ZrC, or TiC were prepared and examined . Workability , tensile properties , and oxidation resistance were tested . Of the columbium alloys studied , the columbium- 12 at . pct vanadium exhibited the best properties ; it compared closely with the columbium- 10 at . pct vanadium alloy studied in a previous investigation.

Jan 1, 1964

By A. Vasebi, É. Poulin, A. Desbiens, D. Hodouin

Maximizing benefits generated by separation plants in the mineral processing industry is of prime importance. To achieve this goal, observers and controllers are both key tools playing a crucial role for economic optimization. Although these methods have been widely discussed in the literature and that numerous applications have been reported, coupling the different algorithms raises practical challenges. The economic function definition, the selection of the real-time optimization structure, the elaboration of observer and controller models, the controller development, and the tuning of stochastic and deterministic parameters strongly influence economic performances. The objective of the paper is to discuss the major difficulties related to the implementation of a real-time optimization system and highlight the benefits of linking data reconciliation and model predictive control for a simulated flotation plant. A systematic topdown approach is used to go through the main design phases and to comment on the different options available for the development of the optimization structure. An internal model predictive controller coupled with a stationary observer is applied for the direct optimization of a three-stage flotation plant simulator based on a phenomenological model. The results show performance improvements in terms of increased revenues brought by reduced grade variability and collector consumption. The discussion also proposes alternative avenues that could be taken to achieve comparable improvements. Finally, since the limited simulated case-study cannot provide a complete understanding of the benefits brought by a data reconciliation observer, recommendations for industrial applications, which are more complex, are provided to promote effective implementations.

Jan 1, 2016

By P. E. Cavanagh

THE Ontario Research Foundation has developed a family of dry magnetic concentrators which, when used in conjunction with a dry grinding mill such as an Aero-fall mill, will allow the production of a completely dry magnetite concentrate. Previous experience with extrusion of iron ore and with pelletizing of fine iron concentrates suggested that it might be possible to develop a method particularly suited to the agglomeration of completely dry concentrates which might have some practical advantages over other methods of agglomeration. Pelletizing is the preferred method of agglomerating very fine iron ore concentrates. Magnetite concentrate is fod to the pelletizing equipment in the form of a moist filter cake. Binders and plasticizers may be added if necessary, and the moisture content must be increased or adjusted to the percentage necessary to give good balling action and satisfactory green strength in the resulting moist pellets. The moist ore with a closely controlled water content of about 7 to 12 per cent moisture may be rolled into pellets by a snow-balling action in a pelletizing drum, a Lurgi pan, or a Mac-Dowell disc pelletizer. The resulting green pellets are fired by one of several alternative processes to produce a hard pellet which has sufficient strength to withstand handling and shipping.

Jan 1, 1957

By Fumito Tanaka

The Mitsubishi Process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates. Continuous converting originates from the application of the proven technology of a lime-ferrite slag (CaO-FeOX-Cu2O) on the Converting Furnace (C-furnace). Recent improvements on the C-furnace operation have included increasing the processing of recycled materials and the investigation of alternative fluxing agents. However, some minor oxides adversely affect C-furnace operation, with respect to magnetite behavior of the slag, with the most significant impact having been observed with the silica content of the slag. This paper will quantify the impact of silica on the lime-based slag, and discusses the controls that have been identified to sustain continuous converting operation.

Jan 1, 2005

By J. Jung, W. Keller, N. Rohn

In hydrometallurgical minerals processing slurries are often processed at very small grind sizes and high solids concentrations. This normally results in flow anomalies of such slurries. Due to flow limits or yield stress the slurry tends to stagnate close to the vessel bottom, the walls and at any internals. The main mixing task therefore generally is not suspending of the solids but the homogeneous blending of the entire vessel volume. If not considered during the agitator design only a fraction of the vessel contents will be mixed. Therefore the knowledge of the slurry rheology as well as the variations in process parameters is vital to design e.g. storage or surge tanks. The integral mixing solution considers the motor power, the choice of the impeller type and number, the impeller diameter as well as the design of the baffles and feed and discharge positions.

Jan 1, 2014

By P Dean, M Elmouttie, Y Duan, X Luo

Slope instability is one of the major concerns in open pit mining operations. A significant collapse of the pit wall can result in injuries, damage to machinery and interruptions to production. A broadband microseismic monitoring technique has been developed for diagnosing the healthy condition of a target slope area. This technique has been successfully applied to an open pit mine in Chile. Our research has found that this microseismic monitoring technique can be used in open pits for tracking and locating a falling rock that is rolling on a slope, if a dedicated seismic sensor network has been established. In collaboration with other monitoring techniques (radar, laser scan, aerial photography), more accurate determination of rock rolling trajectories can be obtained. In this paper, an example of using the CSIRO microseismic monitoring technique at an open pit mine is presented. Results from an experiment where we used the microseismic technique for determination of the trajectory of a rockfalling on a slope are also presented.

Nov 8, 2021

By Artur Skoczylas, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

In many underground mines the excavated ore is produced during the blasting process. Drilling machines that are used to drill the blastholes, where later the explosives will be mounted, are crucial for this task. In order to optimize the currently used techniques, great emphasis is placed on increasing the efficiency and safety of blasthole drilling operations. The natural consequence is the development of monitoring systems and algorithms for processing operational and historical data. In this article, we present the result of the analysis of drilling data carried out as part of the IlluMINEation project. The paper proposes an algorithm for work cycle detection for drilling machines, together with the estimation of general operating parameters and diagnosing the drilling process on the basis of long-term data. Based on the available data, selected components of the drilling cycles have been indicated. Several approaches based on the parameters of the defined cycles are proposed. These approaches can be used in the future to create a full-fledged system for examining the effectiveness and safety of mining drilling rigs.

Jun 25, 2023

By Milton Blander

A review of concepts and theories for predicting thermodynamic solution properties of multi- component high temperature liquid solutions is reviewed. During the last 50 years the ability to predict :such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.

Jan 1, 1996