Search Documents

By T. T. Lin, N. H. Madsen, K. Groom, B. A. Chin

"The objective of this research is to investigate the feasibility of using infrared sensors to monitor the welding process. Data were gathered using an infrared camera which was trained on the molten metal pool during the welding operation. Several types of process perturbations which result in weld defects were then intentionally induced and the resulting thermal images monitored. Gas tungsten arc using AC and DC currents and gas metal arc welding processes were investigated using steel, aluminum and stainless steel plate materials. The thermal images obtained in the three materials and different welding processes revealed nearly identical patterns for the same induced process perturbation. Based upon these results, infrared thermography is a method which may be very applicable to automation of the welding process.IntroductionAutomatic welding is commonplace in industry today. However, most, if not all, involves preprogramming for performance of a repetitive task. These systems are incapable of correcting for perturbations which arise during the welding process. Control of the welding process requires the identification and monitoring of perturbations in a wide variety of parameters. The varied nature of these parameters and the large number of variables involved have thwarted previous attempts at closed loop control of the welding process. The sensor(s) employed by a control system need to meet rather strenuous requirements. First and foremost of these is that such a sensor must be able to identify and discriminate between perturbations that might affect the quality of the weld, including such geometrical perturbations as a change of direction in the seam between the parts being welded, gaps in the seam or a misalignment of the parts being welded. The sensor should also be able to locate and identify contaminants and impurities in the weld puddle and ahead of it while monitoring the extent of the heat-affected zone and the cooling rate of the metal. The sensor(s) should, additionally, be able to perform these tasks in a time frame that is consistent with automatic control of the welding process. This paper presents results that could aid in the assembly of such a controlled welding system."

Jan 1, 1986

By David Baker

IN a paper presented to the American Institute of Mining Engineers, September, 1904, entitled ? Improvements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low-thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace gases, unequal reduction, slips, scaffolds, irregular cutting of the. inwall, " off " iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from successively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very simple form of rotary distributor, which may be applied to any form of double-bell charger, retaining the perfect gas-seal, which is so admirably obtained by that construction. In seeking protection for this invention, I found no similar distributor on record in the patent offices of the various countries where application was made; but an application show-

Jul 1, 1906

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By Essie Esterhuizen, John Ellenberger, Dennis Dolinar

"Underground stone mines in the United States use the room-and- pillar method of mining. The stability of the roof between pillars determines the mining dimensions and size of equipment that can be used. The findings of a survey of roof span stability issues and design practices are presented, and the observed factors contributing to roof instability are discussed. Identified stability issues are evaluated, such as maximum roof span, horizontal stress, and roof beam stability. The results of field observations, roof monitoring, and numerical analyses are used in the evaluation. The importance of the first roof beam thickness and its impact on roof stability and support requirements is presented. An evaluation of the current experience with stone mine roof spans relative to international experience is presented. A step-by-step design procedure is suggested which emphazises the need to collect adequate geotechnical data, understand the immediate roof stability, select a mining direction, and meet support requirements.INTRODUCTIONIn room-and-pillar mines, the roof between the pillars is required to remain stable during mining operations for haulage as well as access to the working areas. Roof and rib falls account for about 15% of all reportable injuries in underground stone mines (Mine Safety and Health Administration, 2009). Therefore, the stability of the roof is an important safety consideration. The size of the rooms in underground stone mines is largely dictated by the size of the mining equipment. Large mining equipment is used, requiring openings that are on average 13.5 m (44 ft) wide by approximately 7.5 m (25 ft) high to operate effectively (Esterhuizen et al., 2007). The dimensions of the roof spans are largely predetermined by the equipment requirements, and design is focused on optimizing stability under the prevailing rock conditions. If the rock mass conditions are such that the desired stable spans cannot be achieved cost effectively, it is unlikely that underground mining will proceed. In addition, large roof falls can extend across the full width of a room and may extend more than 5 m (16 ft) above the roof line. These large falls are a safety hazard and can have a significant impact on mine access and production. The National Institute for Occupational Safety and Health (NIOSH) research into stone mine roof stability has focused on identifying both the causes of roof instability and techniques to optimize stability through design."

Jan 1, 2010

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By M. J. King, D. A. Van den berg, R. Fukuzawa

"Mercury bearing ore bodies are often treated for the production of copper, lead, zinc, gold, and silver. The mercury deports either to tailings or is collected during various stages of the extraction process. This paper reviews the relationship between various mercury collection processes and the subsequent management of the mercury by-product or waste. It focuses on mercury removal sequestration including cementation, sulphide precipitation, bulk neutralization, and carbon adsorption. Long term mercury management strategies including third-party stabilization, stabilized mercury co-disposal, secure storage, and mercury recycle are also evaluated. INTRODUCTIONMercury is produced in North America as a by-product of non-ferrous metals processing and from recycling of products such as dental amalgam, fluorescent lamps, and thermometers. Its toxicity is recognized to have significant negative impacts on the environment and human health. As a result, many countries are adopting regulations limiting mercury use and its uncontrolled release.The European Union banned mercury exports in 2011 and the United States will do so in 2013. The export bans aim to prevent mercury use in developing countries for activities such as artisanal small scale gold mining. However, by-product mercury production from the non-ferrous metals industries continues.These factors contribute to an oversupply of mercury and the need to find suitable treatment methods for the long term management and storage of mercury and mercury bearing materials."

Jan 1, 2012

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By Lewis Reeve

As. part of a program of investigation of the properties of electric arc welds carried out in the laboratories of the A. 0. Smith Corporation, considerable work has been done on the determination of the oxygen, nitrogen and hydrogen content of different types of weld metal, employing for this purpose the so-called "vacuum fusion method." It is the purpose of this paper to describe certain improvements that have been introduced in this method of determining the gas content of metals, with particular references to the steel specimens examined in this investigation. The method and apparatus used at the beginning of the investigation were essentially those of the Bureau of Standards as described by Vacher and Jordan.1 Later a number of changes were introduced which resulted in. more rapid evacuation of the graphite crucibles employed and which enabled larger volumes of gas to be dealt with than could be handled conveniently in the Bureau of Standards equipment. In addition, the analyzing of the gases evolved from a melt in the same apparatus as collected was abandoned in favor of analysis outside the equipment using standard methods of gas analysis. The time required for gas analysis in the apparatus itself, as described by the Bureau of Standards, was found to be considerable, and during this time the rest of the equip-ment was tied up, preventing its use for the analysis of further steel sam-ples. As a result of the modifications introduced, the time required for the analysis of a steel sample for gas content was reduced from about 8 hours to less than 3 hours. Subsequently, the whole procedure of melting the sample and collect-ing the gases evolved was modified so as to enable a distinction to be drawn between the easily reducible oxides such as iron oxide and the more stable oxides such as silica and alumina. At the same time evidence was obtained indicating the probable existence in the steels of other nitrides than those of iron alone and making possible their quantitative determination.

Jan 1, 1933

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer's machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Jean Wehbe, Daniel C. Brahana

"The new Mercedes-Benz Stadium (MBS), home of the Atlanta Falcons, is part of a new era of stadium construction in the U.S. These new-age stadiums are larger and have more amenities than their predecessors. Many of the MBS’s features, including its innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are supported by drilled piers. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 ft (1.8 m and 1.9 m). Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings were used to support the more lightly loaded portions of the structure.The focus of this article is the construction aspects of the drilled pier foundations. Initially, a fairly extensive drilled pier load test program was performed. Load testing included a Statnamic compression test, two Osterberg Cell tests and two lateral tests. Production pier installation included over 3,800 linear ft (1,158.2 m) of earth excavation and over 1,350 linear ft (411.4 m) of hard rock excavation. The piers contain more than 6,600 cu yd (4,587.3 cu m) of concrete and 1,100 tons (998 tonnes) of reinforcing steel. Drilled pier installation took about 4.5 months. ABE Enterprises was the specialty foundation subcontractor and Bauer-Pileco was the equipment provider.Site and Subsurface ConditionsThe project site is in downtown Atlanta and was originally occupied by residential buildings. A portion of the site was later developed as a rail yard, and other areas contained light manufacturing, warehouses and other relatively light structures. For the past 15 to 20 years the site had been used for surface parking.Beneath a surficial layer of manmade fill, soil test borings at the site generally encountered residual soil, partially weathered rock and the parent bedrock. The bedrock at the site is highly variable, both in elevation and in hardness/quality. The depth to rock is reasonably uniform within the western two-thirds of the site at about 20 to 50 ft (6 to 15.2 m), with a few exceptions. In the eastern third of the site, the rock drops off dramatically to the north and east. In one mega column cap, there was almost 80 ft (24.3 m) in elevation difference. In two borings in the cap that were 20 ft (6.1 m) apart, the top of rock varied in elevation by 34 ft (10.3 m)"

Jan 1, 2016

By M. E. Rossi, C. Badenhorst

Conditional bias occurs when the expected value of the true grade conditional on the estimated grade is not equal to the estimated grade. It is a quantification of how the average of estimates differs from the true value. Conditional bias is present in all resource estimates due to the unavoidable properties of kriging, and indeed all linear estimation (regression) methods. In a mining resource estimation context, the degree of conditional bias is dependent on the spacing of the conditioning data; more data leads to the expectation of less conditional bias This paper discusses conditional bias from two perspectives: 1. 2. Estimates seeking to eliminate, as much as possible, conditional bias; and Estimates that accept a larger amount of conditional bias in resource models, in order to achieve a specific outcome. The problem of conditional bias in estimation can only be fully appreciated if the objective or purpose of a resource model is understood. There are instances where conditional bias should be avoided because it is not reasonable to make decisions using estimates that are known to be wrong in expected value; for example, when making a final decision in grade control with respect to the destination of the material. In most instances in the mining resource estimation context, however, the estimated values will not be “final estimates”, but “interim estimates”, meaning that in the future more data will be obtained, and the ”interim estimate” will then be updated. In this context, the most useful resource model is an interim model that is able to predict the final model estimates, despite not having all the data available that will be collected in the future. This is the objective, for example, of a recoverable “long-term” model developed prior to operating a mine, for example at the feasibility stage. It attempts to predict the ore that a processing plant will receive, well into the future. In such cases, it can be unequivocally demonstrated that conditional bias is not only unavoidable, it is a necessity.

Sep 1, 2021

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By Keith Eldridge, Robert Kelly

"Quality management has a/ways played an important role at the Iron Ore Company of Canada; particularly since the early eighties when the iron ore markets favoured buyers as opposed to sellers.Since thot time, IOC's quality system has evolved from basic quality control to the Deming philosophy and its 14 points, and on through various other phases to the ISO 9000 series.ISO 9002 Registration was' first requested by IDC's customers and development plans were prepared in 1988. At this time, Quality System Registration was unheard of in the mining sector and TDC found itself struggling with the concept. The 1U!Xt three years saw the company develop a Quality System to meet ISO 9002 in a two phased approach, setting new standards for the mining industry when registration was achieved in December 1991.The company now sees ISO Registration as the cornerstone of its future quality efforts. IOC's quality system has been integrated with several other initiatives such as loss control and functional training, both of which focus on training and management the workforce to do the job safely, the right way.This paper addresses the steps required to develop a quality system for the mining industry within the guidelines of the ISO 9000 Series and the subsequent integration of other quality related initiatives."

Jan 1, 1994