Search Documents

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By D. Van Tonder

ABSTRACT The comparative economics of ion exchange and direct precipitation have been analyzed by developing indicative CAPEX/OPEX models for typical alkaline leach uranium circuits. An agitated tank ore leach application is considered, comparing resin-in-pulp and direct precipitation as recovery options. Capital and operating cost estimates are derived from rates and factors used in recent studies and projects. The analysis showed the main economic drivers to be the ore grade and resin loading. The resin loading is impacted by the prevalence of competing ions, especially chloride. At resin-in-pulp solution chloride concentrations below 3 g/L and uranium grade below 640 g/t U3O8, resin-in-pulp is more economical, whereas at chloride concentrations above 3 g/L, direct precipitation is more economical.

Jan 1, 2012

By J Palarski

Over the last 100 years in the Polish mining industry considerable work has been done to assess optimum slurry, develop flexible delivery systems and adjust the fill technology to a wide variety of mining and geological conditions. Sand or industrial mineral waste materials for the backfilling of underground voids are used to control ground movement and surface deformation. This paper discusses various criteria to he considered in the preparation of a fill, including slurry properties, mine infrastructure, mining geometry, placement methods and the purpose of the backfill. This paper presents laboratory and in situ test data on the influence of materials parameters on the slurry flow in a pipeline system, stiffness, permeability, binding time and strength of a backfill, on the distribution of mixture in underground voids or the penetration between roof fall Materials.

Jan 1, 1998

By M. Kashiwada

The zinc leach residues are introduced into waelz kiln to fume volatile metals and before the end of 1967, the waelz-fume containing zinc, lead, cadmium and indium was directly recycled back to the leaching process for the production of electrolytic slab zinc. However, since 1968, we have been recovering with success those valuable metals contained in the fume separately instead of direct leaching. According to the improved process, the waelz-fume, after being mixed with chloridizing agents, is fed into the rotary kiln to be roasted, wherein most of lead and cadmium content is collected as fume and most of zinc remains in the calcine. Zinc calcine thus obtained, containing 70 to 75 per cent zinc and, less than 1.0 per cent lead is sent to zinc plant for further recovery and the fume containing 40 to 50 per cent lead and 3 to 6 per cent cadmium is further processed to recover lead, cadmium and indium. The advantage of this process can be secured to the utmost when it is combined with the following subsequent treatments. (a) Blast furnace smelting of non-magnetic waelz slag to recover copper, silver and gold as matte. (b) Gallium recovering process from magnetic waelz slag. (c) Soda process of lead bearing cake produced after removing cadmium and indium from the said fume. Thus the extractions of zinc, lead and cadmium from leach residues account for 87 per cent, 72 per cent and 85 per cent respectively.

Jan 1, 1970

By B. J. Scheiner

As part of the goal to maximize minerals and metals recovery from primary domestic resources, design factors associated with minimizing current leakage in bipolar cell configurations were studied by the Bureau of Mines as a means of improving the efficiency of bipolar e1ectrooxidation cells. Initial studies that were conducted in a small bipolar cell operating at 140 to 145 volts and 15.4 amp indicated how design factors could be employed to minimize cur-rent leakage around adjacent electrodes during cell operation. Based on these results, a 40-electrode, 108-kva prototype of an industrial-sized cell was constructed and tested for extracting metal values from offgrade molybdenite concentrates. The feasibility of recovering molybdenum and rhenium from the oxidized pulp also was determined. Feed to the process sequence consisted of flotation concentrates containing 16 to 35 pet Mo as molybdenite and 6 to 15 pct Cu. E1ectrooxidation in the prototype cell resulted in 84 to 97 pct Mo and Re extraction with a corresponding energy consumption of 9 to 13 kwhr/1b Mo extracted.

Jan 1, 1979

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By U. A. Peuker

"Steam Pressure Filtration (SPF) is a modified cake filtration process and is characterized by both washing and excellent de-watering of the filter cake. Compared to conventional gas differential pressure filtration, the filter cake is treated with saturated or superheated steam replacing pressurized air. Invented in the early last century, Steam Pressure Filtration has reached technical maturity in the 1990ies for inorganic particle systems, fine chemicals and coal. Especially the de-watering performance for fine particles systems below 50 µm make Steam Pressure Filtration an excellent option for the processing of fine tailings streams, to produce a stable material, which can be described by the methods of solids mechanics instead of paste rheology. The washing, which is due to the condensing steam, is able to reduce the ion load of the solid. This additional effect is able to generate a dry tailings material, which shows a reduced leaching potential of mobile ions, which originally derive from the process water. INTRODUCTION Steam Pressure Filtration is a process concept especially of hyperbaric filtration, which started its market entry in the 1990ies (Bott 1996, Bott 2002). Even though there have been many attempts to apply steam on filters before, the success story began with the combination of hyperbaric filtration and steam application and the technical solution to limit the steam treatment to a defined zone on the filter. This resulted from the scientific findings that steam mainly enhances the de-watering during the mechanical filtration (Gerl 1999). There are no or minor positive effects of steam application to a filtration process during cake filtration and after the steam breakthrough has occurred. Furthermore that time a sufficient control technology to regulate the steam consumption as well as suitable filter cloths became available. There is a growing need for de-watering technology in the mining industry, not only for the concentrate but also for the tailings streams. Several reasons argue against the established solution of damping the tails as suspension or paste into tailings ponds. There are ecological, political, societal and economic reasons, which question the tailings ponds more and more. Due to the increasing costs in the building and monitoring of tailings dams, which contain the tailing ponds, the concept of dry stocking using filtration technology comes into the game (Jansson 2016). Dry stocking converts the tailings stream form the suspension or paste state, into a material, which can be stockpiled. The latter typically is a moist flowable disperse particle system. The conversion involves a de-watering step, in which different types of filter equipment can be used, e.g. filter presses, membrane filter presses, automatic press filters or hyperbaric filters. For coarse products also vacuum filter can be applied. Due to its excellent de-watering performance and the easy scale-up properties Steam Pressure Filtration is further option for dry tailings stacking."

Jan 1, 2018

By Ralph W. M. Lai

The liquid membrane separation process was first patented in 1968 for separating hydrocarbons.(1-4) This stimulated many researchers to join in the area of separating organic compounds. l Since then, its applications have been extended to the removal of contaminants from waste water,(12-33) encapsulation of enzymes and/or microorganisms for reaction and/or separation, (24-28) oxygenation of blood (artificial lung),(19) removal of toxins from blood (artificial kidney)(26,20) and metal extraction.(31-63) This paper discusses the possible process schemes for using liquid membranes to separate and concentrate copper ion from its acidic leaching solution.

Jan 1, 1982

By Hans Lundberg, Basil T. Wilson, H. Steuart Scott

FOR the benefit of those readers who may not be in close touch with present practices in the geophysical prospecting for ore, brief reference will fiat be made to the advantages and shortcomings of the methods to be discussed. Magnetic and electric methods are generally accepted as the most useful for ore prospecting. By magnetic methods, magnetic intensities that are not normal may be recorded and outlined. From these can he located concentrations of such highly magnetic minerals as magnetite or pyrrhotite, which sometimes occur in such large masses that they are of economic value in themselves. More often. however, these magnetic min¬erals are associated with others, such as copper, zinc, lead, gold, and silver, which, if existing in sufficient concentration and quantity, may constitute valuable ore bodies. It is therefore only when pyrrhotite and magnetite are present in these bodies that the magnetic method can be used to indicate their presence.

Jan 1, 1945

By Abigail A. Myers, Michael A. Milczarek

Mining impacts to groundwater are being comprehensively regulated for the first time in Arizona with the implementation of the Aquifer Protection Permit Program. This far reaching program is one of the nation's strongest groundwater quality protection programs. Aquifer Protection Pennits (APPs) are required for almost all mining operations and will compel mining companies to pay increased attention to the potential groundwater quality impacts from their activities. All regulated mining operations will have to employ discharge control technologies and monitoring will be heavily emphasized. Technical requirements and relevant permit conditions are discussed.

Jan 1, 1991

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By Clement K. Chase

Since the dam of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extractions. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946