Search Documents

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

To develop a magnetic levitation transport system that can reduce the cost and improve safety in transporting coal from the face of underground coal mines to the surface. Background Many conventional mining operations use conveyor belts to transport coal from an underground face to the surface of the mine. The Mag-Lev Transport System design replaces conveyor belts with magnetically levitated coal haulage containers moving through a dedicated pipe¬line. Cost estimates, based on current design data, show the Mag-Lev Transport System would have operating and capital costs that are less than or equal to those of an equivalent-capacity conveyor belt system. The safety hazards associated with conveyor belt systems include exposure to moving parts and pinch points, potential fire hazards due to mechanical friction, and the exposure of miners to respirable dust. These hazards would be eliminated or significantly reduced by this novel technology. Approach The Mag-Lev Transport System uses magnetic levitation technology that allows noncontact, frictionless conveyance of a levitated body within a dedicated transit corridor. The mag-lev technology utilizes two types of permanent magnets coupled with an electronic position control system to achieve noncontact levitation. Levitation is provided by neodymium-iron boron (NdFeB) magnets mounted in the base of the haulage containers and inexpensive ceramic-5 magnets located in the bed of the transit corridor. An electronic position control system is used to overcome the inherent instability of the repelling permanent magnets. Proximity sensors, a signal processing circuit, electromagnetic actuators, and fixed ferrous side rails are the major components of the positioning system.

Jan 1, 1994

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

By John C. Edwards

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization-and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m-l for smoldering and flaming coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m-l, whereas the optical smoke detectors showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 2010

By H E. S Moorcroft, D Scott

The increasing mining depths of South African gold mine deposits are resulting in ever-increasing heat loads associated with depth and the geothermal gradient. Together with changes in the mining horizons brought about by the depletion of older, shallower, high-grade reserves, this leads to the need for the continuous review and redesign of cooling requirements. Traditionally, cooling requirements were met by using a combination of cooling strategies, including bulk air cooling on surface and underground. If this proved to be insufficient, chilled service water and secondary remote air-cooling systems were introduced. This paper reviews these practices in order to provide a cost-effective means of catering for the introduction of hydropower at the Gold Fields Ltd South African operations. Some of the equipment that has been developed to meet the requirements of both hydropower and refrigeration includes hydropower fans, cooling coils and in-stope venturis. These are individually described and discussed, together with their roles within the greater strategy. The planned change in the cooling strategy and the employment of these technologies have effectively doubled the cooling available, from 10 MW to more than 20 MW, extracted from the hydropower water used to drive the mining equipment. In conclusion, the cooling strategy described allows a total heat load of approximately 52 MW to be successfully ventilated and cooled through the use of combined surface and underground refrigeration installations, and through the use of hydropower-chilled water.

Jan 1, 2005

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By Daguang Lu

The section of sintering and BF (blast furnace) is very important in iron-making process. In practice, the scheduling is so extensive that three faults unfavorable to continuous product will be easier to happen. This paper introduces the integration Petri Net and GA (genetic algorithm) as suitable tools for simulation and optimization of scheduling to section of sintering- BF under a certain hot iron or-der. The situation of the iron plant Chongqing Iron and Steel Company is researched in approach above mentioned. By analysis, the conclusion is drawn that scheduling with optimized values can maintain continuity of key operations , can satisfy order of hot iron in maximal degree and can keep the best stability of key storages.

Jan 1, 2009

By Sidney Katell

The present report, a continuation of the series of Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, is concerned with articles published from January 1958 through December 1958. The periods covered in previous reports are as follows: January 1930 - August 1948 I. C. 7516 September 1948 - June 1952 I. C. 7705 July 1952 - June 1954 1. C. 7751 July 1954 - December 1956 I. C. 7847 January 1957 - December 1957 I. C. The following sources were used to obtain the references to and the abstracts of the published articles included in this report: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Coal Age. 6. Coal Utilization. 7. Cost Engineering. 8. Industrial and Engineering Chemistry. 9. Nucleonics. 10. Oil and Gas Journal. 11. Petroleum Engineering. 12. Petroleum Refiner. 13. World Oil.

Jan 1, 1959

By C. R. Edwards, D. R. G. Watt

"Equity Silver Mines Ltd. a member of the Placer Development group of companies operates Canada's largest silver mine near Houston in north-central British Columbia. Initially, the silver-gold-copper flotation concentrate contained excessive levels of antimony and arsenic, so a leach process was installed to remove undesirable metals and provide improved smelter terms for the leached concentrate. The leach plant which has been fully described elsewhere (1, 2, 3), was forced by deteriorating process economics to shut down in April 1984. Equipment was mothballed and alternate uses sought.The Endako Mines Division of Placer Development Limited, located some 150 kilometres east of the Equity mine site, shut down its molybdenite mining and milling facilities in the spring of 1982. Endako has continued to produce molybdic oxide (molybdenum trioxide or MTO) via intermittent roaster runs, and also a high purity, lubricant grade molybdenum disulfide in the Ultrapure Plant. With the steel industry in the doldrums, molybdenum chemicals present an alternate and growing potential for molybdenum sales. In 1982 Placer Development began testing this market. Molybdenum chemicals were produced in the United States on a toll basis using Endako MTO as process feed. The transfer of this production to Canada was being considered when Equity's leach plant shut down, and it was noted that most of the equipment and skills necessary could be provided by the leach plant. See Figure 1.A careful investigation of process requirements was completed by engineering and production staff at Equity and Endako. A provisional capital and operating cost estimate was made, and it was decided to perform a test run during July 1984. There were strong reasons to proceed with this project. A positive cash flow was expected for both Endako and Equity. Endako would have product to continue to expand in the molybdenum chemicals market with the added selling point that now the complete production process would be under direct control of Placer Development companies. Equity would further benefit since a portion of the leach plant would continue in operation thus maintaining and exercising our hydrometallurgical engineering and operating skills. Finally, Equity would have a base from which to search out other processes adaptable to the idled leach plant equipment."

Jan 1, 1986

By M. J. Sapko

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL's Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal's ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

Jan 1, 2003

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By F Hungerford, T Ren

"Gas management has always been a major concern for the ventilation officer of any gassy mine. With an increase of mining depth and gas content, there is a great demand for the development of in-seam drilling sites where boreholes can be drilled for the pre-drainage of gas prior to longwall operation. The ventilation and gas management in the drilling site therefore becomes a critical component of mine safety. In this study, advanced computational fluid dynamics technology was adopted to investigate the aerodynamics of gas emitting from the drilling site and boreholes during normal drilling and, in the case of a sudden gas inrush, from the borehole. In addition, the impact of different ventilation controls on gas removal in the drilling site was investigated. Modelling results indicate that gas accumulation zones could be formed if the ventilation system fails to deliver sufficient airflow to the drill site, especially when a sudden gas inrush from a borehole occurs. The configurations of brattice, layout of ventilation tubes and the gas emission rate all have a significant effect on the gas distribution. Due to variations in site-specific conditions, it would be desirable to conduct modelling studies to assess the effects and efficiencies of a ventilation design for the varying environment on-site before carrying out drilling practice. CITATION: Ren, T, Hungerford, F and Wang, Z, 2015. Computational modelling studies of ventilation management for underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference, pp 239–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By Yoshinobu Fukumori, Testuya Watanabe, Futoshi Shikata, Hiroyuki Tokumitsu, Hideki Ichikawa, Masahito Miyamoto

Nano-particulate systems have attracted much attention recently in pharmaceutical field as drug carriers and functional components of pharmaceutical dosage forms. This paper describes our approaches in design and preparation of nano-particulate systems, including lipid nano-emulsions, chitosan nanoparticles and thermosensitive acrylic nanoparticles, for certain pharmaceutical applications mentioned below. The lipid nano-emulsions with their particle size smaller than 100 nm were prepared for gadolinium neutron-capture therapy (Gd-NCT) of cancer by a thin-film hydration method with sonication, and intraperitoneally injected into Greene's melanoma (melanotic No. 179)-bearing Syrian hamsters. This provided such a high gadolinium concentraton in tumor as 107 µg/g tumor (wet basis) at 48 h after administration. As an alternative gadolinium nano-carrier for Gd-NCT, biodegradable and highly gadopentetate-loaded chitosan nanoparticles (Gd-nanoCPs, 426 mTI in particle diameter and 9.3% in Gd content) were prepared by a novel emulsion-droplet coalescence technique. A significant tumor-killing effect could be obtained when Gd-nanoCP suspension was injected intratumorally twice 24 and 8 hours before neutron irradiation into B 16Fl O melanoma-bearing mice and subsequently thermalneutron was irradiated toward tumor site with a flux of 2 x 109 n/cm2/sec for 60 min. As one another application of nanoparticles, a novel acrylic composite latex with a hydrophobic core and a thermosenstively swellable shell was designed for fabricating microcapsules showing thermosensitive mode of drug release. The microcapsules with the composite latex-dispersing membranes exhibited an exceptionally rapid on-off response of drug-release in a thermosensitive manner.

Jan 1, 2000

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

By M Wagner, H Assimi, F Neumann, C Garcia, B Koch

Run-of-Mine (ROM) stockpiles are the inventory of valuable materials extracted from the mine. Depending on the customer requests, a selective addition of ore from stockyards should be selected at the required tonnage. In the stockyard, stackers and reclaimers are the machines which load and unload ore, respectively. Currently, humans determine the reclaiming/stacking planning sequence in the stockyard by rules of thumb. However, this is a complex task subject to multiple operational constraints, such as where undesirable mineral properties should not exceed certain limits in a request. Human planning can lead to limited decision support and lower ability to consider the upcoming blends and requests. This kind of decision making can cause perturbations in the assumed profit and unexpected loss in practice. Therefore, an intelligent decision-maker and sequence planner would be highly valuable to automate stacking and reclaiming operations in practice. The benefits are reducing variability in decision-making and operation costs. This paper considers a stockyard with available mineral information in the stockpiles using load and dump locations from GPS data feeds. We present an optimisation problem to find a solution which results in reclaiming more ore in a shorter time. To solve the problem, we develop an automatic search strategy based on the greedy search algorithm independent of the type of machine used in reclaiming. The proposed method plans a sequence for stockyard recovery blend optimisation to meet multiple customer demands in a timeframe. Blend optimisation is subject to various constraints such as the elemental composition of the valuable materials and penalty elements. We present three case studies using EKA’s simulator, to fulfil two to four requests from four stockpiles. We compare the obtained results with a pilgrim step reclaiming heuristic and we show how our proposed search strategy outperforms the current strategy used in practice.

Nov 10, 2020

By E. A. C. Chamberlain

New techniques for the continuous sampling and analysis of mine air are expected to replace traditional methods used for the early detection of spontaneous combustion. It has been established that the rate of evolution of carbon monoxide is the earliest indicator of incipient spontaneous combustion. Two methods of continuous monitoring of this gas are available and are now in use in the UK collieries. The first is the UNOR infra-red gas analyser, which is flameproof and may be used underground; the second is a system of tube bundles, which permits air to be drawn from any critical point in a colliery and analysed on the surface. Each system has its advantages and disadvantages but both provide the colliery manager with far more information on the condition of his pit than could previously be obtained by spot sampling and laboratory analysis. This paper describes the two systems presently in use and assesses likely future developments.

May 23, 1905

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By Niloy K. Nath

Two layer sintering by charging green sinter mix with normal coke rate in the upper layer and reduced coke rate in the lower layer, can substantially reduce the coke rate and also improve the sinter quality by producing more uniform thermal profile through out the bed height. The two-layer sintering process have been analyzed by numerical simulation of the process by a detailed CFD based model, considering all the important phenomena like gas-solid reaction, melting and solidification, flow through porous bed, heat and mass transfer etc. Optimization techniques like genetic algorithm, differential evolution is then applied to evaluate the optimum coke rate in the two layers of the bed to produce the ideal thermal profile and melting fraction in the sinter bed for optimum sinter quality. Through this optimization method both high quality sinter with minimum return fines can be achieved along with reduced coke rate. Application of a genetic algorithm for this type of process optimization has several advantages over the traditional optimization techniques since it can identify global optimum condition and perform multi-objective optimization much easily for complex industrial process like iron ore sintering. Keywords: Two-layer Sintering, Iron Ore Sinter Quality, Ergun's Equation, Gas-solid reaction, Melting Fraction, Multi Objective Optimization, Pareto Set, Genetic Algorithm

Jan 1, 2003

By L. R. Hougen

The Falconbridge Matte Leach Process yields high-purity nickel chloride by selectively dissolving nickel from copper-nickel converter matte with hydrochloric acid , purifying the solution by solvent extraction and crystallizing NiCl2 4H2O by further acidifying the purified leach liquor. In the Kristiansand Matte Leach Plant, a granular oxide is produced by high-temperature hydrolysis of the nickel chloride for subsequent reduction to a high-purity granular metal product, designated NICKEL 98. This paper describes the investigation of on alternate route to processing nickel chloride in which high-quality cathode nickel is produced by electrowinning from all- chloride electrolyte. The investigation was made in a pilot circuit containing two production-size electrowinning tanks operated in conjunction with the commercial-scale leach plant.

Jan 1, 1977