Search Documents

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Eduardo A. Pérez, Alejandro R. Alonso, Rosa María Luna-Sánchez, Gretchen T. Lapidus

Rare earth elements have been widely used in various sectors, from the aerospace and steel industries, to electronic applications, particularly in displays and batteries for portable devices. The high demand for newer and better equipment, such as cell phones, tablets and lap tops, has increased the consumption of the rare earth elements and at the same time the need for its recovery from electronic wastes. For that reason, the recycling of batteries is important, principally the Ni-HM batteries, due to their elevated content of rare earths elements, in addition to the high concentrations of cobalt and nickel. The current processes are based on dissolution in strong acid solutions (sulfuric acid concentrations from 2 to 4 mol/L), and temperatures from 30 to 90°C. In the present work, electrodes from spent Ni-HM batteries were leached using 1 mol/L H2SO4, in the presence of ozone as the oxidant, where recoveries of 96% for La, Ce and Nd were obtained at room temperature. The separation of Ni and Co from the leach solutions was performed using an electrochemical reactor, after which rare earth elements were precipitated, obtaining a mixture of its hydroxides with impurities below 1%, according to EDS analysis.

Jan 1, 2014

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By M. Vallée

"Geological and technical problems are often considered the most important ones affecting new mining projects. Typical problems and likely causes are reviewed based on current Quality Management and Continuous Improvement (QMCI) perspectives, giving particular attention to the work of W.E. Deming. As the “system approach” is an essential part of these policies, its characteristics are described with particular attention given to cultural- behavioural, organizational and systembased constraints described by J. Gharajedaghi. Given that poor communication and interaction among geologists, mineral processors and mining engineers/operators can seriously affect the adequacy of tests, project planning and execution, and mine profitability, these interrelated processes within the mining systems are analyzed and modelled. The impacts on models and simulations of ignoring typical data, information and knowledge uncertainties are addressed. Adapting W.E. Deming’s Fourteen Points, System of Profound Knowledge and insistence on leadership, and the analysis of mining system constraints, will allow the effective QMCI approach required to reduce geological and technical risks. Whenever we achieve this goal, we will be in a better position to overcome environment-, market-, finance- and community-related problems, achieve higher company and industry profitability as well as more sustained development. RÉSUMÉLes problèmes géologiques et techniques sont souvent considérés les plus importants parmi ceux qui affectent les nouveaux projets miniers. Des problèmes typiques et leur causes sont étudiés dans la perspective de gestion de la qualité et d’amélioration continue (GQAC), en relation avec les travaux de W.E. Deming. Comme l’approche système est au centre de ces méthodes, ses caractéristiques sont décrites en donnant une attention particulière aux contraintes de types culturel-comportemental, organisationnel, et systémique décrites par J. Gharajedaghi. Compte-tenu que les lacunes dans les communications et les interactions entre géologues, minéralurgistes, et ingénieurs/opérateurs miniers peuvent affecter sérieusement la validité des essais, de la planification et de l’exécution des projets ainsi que la rentabilité des exploitations, ces processus connexes font l’objet d’analyse et de modélisation. Les impacts sur les modèles et les simulations de l’incertitude des données, informations et connaissances sont soulignés. En adaptant au système minier les Quatorze Obligations et le Système de connaissance approfondie de W.E. Deming ainsi que l’analyse des trois types de contraintes, nous pourrons développer une approche GQAC permettant de réduire les risques géologiques et techniques des projets miniers et des exploitations. Ceci nous pemettra de mieux faire face aux problèmes reliés à l’environnement, aux marchés, au financement et aux conditions sociales, d’améliorer la rentabilité des exploitations minières et de l’industrie, tout en contribuant de façon accrue au développement durable."

Jan 1, 2003

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

By J Isarua, R Mabiria

The Ok Tedi copper and gold project, located in the Western Province of Papua New Guinea, commenced operations in 1983. The open cut mine has undergone several significant transformations throughout its project life including changes of ownership, mine life extensions and varying production performance profiles. As of today, the Ok Tedi Mine is a 100 per cent PNG owned company (67 per cent State and 33 per cent Western Province and Communities) and has a life-ofmine plan extending out to about 2032.

May 5, 2022

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus' sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By T. E. Wakefield

"Final Galloway (stage) designs for vertical drill and blast shaft sinking projects evolve from complex thought patterns which integrate operational processes, systems and methods of communication, power supply, drilling, blasting, ventilating, mucking, supporting, surveying, dewatering, sealing, concrete lining and shaft furnishing. Attention to ergonomic design detail at the shaftsman / structure interface is at the heart of safe and successful multi-deck working platforms. For economy the end product must have a low mass to reduce suspension rope end loads to be able to use smaller suspension hoists and have lighter headframe structures, be robust to withstand concussion damage, be easily constructible on site, be maintainable in the shaft barrel, and comply with safety and legislated standards. This paper’s ambition is to describe a systematic design framework and sequenced thought process that delivers a product that is engineered with excellence, illustrated by making use of two designs that evolved during recent Galloway projects, one destined for a large diameter man/material shaft, the other for a ventilation shaft. The stage engineering iterative process starts with mapping permanent and sinking hoisting layouts, followed by laying out horizontal deck plans, mostly constrained by the permanent shaft purpose and configuration, whilst maximizing openings to enable muck to be removed rapidly for the best sinking cycles. Concurrently the designer needs to understand the chosen sinking methodologies in conjunction with crewing to determine the number of decks and fix their spacing. Insufficient access to move and line up formwork, set reinforcing rods and pour concrete in the confined spaces of the stage is an inherent major risk to be mitigated. An iterative and integrative process follows for the primary configuration which delves into increasing design detail, accommodating all other methodology influences, resulting in 3D layouts for further risk assessment, review and fine tuning by seasoned shaftsmen. INTRODUCTION Documented colliery shaft sinking practice from the late 1800’s makes reference to purpose built walling (bricked lining) cribs with floors suspended in sinking shafts, thereby allowing shaft lining to proceed concurrently with the excavation. Improvements were made by Sir William Galloway who introduced two decks supported at the corners by angle irons. The sinking stage, or Galloway, has developed substantially over time to be the in-barrel heart of the sinking operation, with overwhelming complexity for those who have to design one for the first time."

Jan 1, 2019

By T. Gerritsen, R. MacRosty, R. Pula

For several years Hatch has been installing fibre optic temperature sensors on the copper cooling elements of smelting furnaces to improve monitoring capabilities in critical locations. The metal/matte tapblock is a key area to monitor in the furnace as it undergoes severe wear from the molten material repeatedly drained through it. The high wear rate around the tapblock means downtime is necessary to perform refractory repairs. A good understanding of the tapblock condition allows the operation to maximize safety and production; consequently the metal/matte tapblocks have been the focus of this study. Fibre optic technology allows the installation of numerous sensors in locations that are very sensitive to refractory thickness, thereby providing information previously unavailable with traditional measurements. The transient nature of the thermal response to tapping and the three-dimensional geometry of the tapblock confound the interpretation of refractory thickness from temperature measurements. This paper focuses on the analysis of both plant data and thermal modelling simulations and details the progress made in relating the temperature measurements to the refractory thickness in front of the copper tapblock.

Jan 1, 2014

By M. Scaggs, L. R. Mendoza

"On January 9, 2014, a large chemical spill occurred on the bank of the Elk River near Charleston, WV. Within hours, the potable water supply for more than 300,000 people was contaminated, and the incident captured national headlines for weeks. Although the primary chemical, crude 4-methylcyclohexanemethanol, or MCHM, is deemed nonhazardous, the impacts of the spill are significant – with all stakeholders, including the public, members of industry, and relevant government agencies experiencing losses. This case highlights the need for a more proactive approach to environmental management, shifting from crisis control and remediation to crisis prevention and risk management. INTRODUCTION On the morning of January 9, 2014, approximately 10,000 gallons of crude 4-methylcyclohexanemethanol (MCHM) leaked from a 48,000-gallon storage tank sitting on the bank of the Elk River near Charleston, West Virginia (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal, and is deemed nonhazardous in terms of transportation and storage regulations and also toxicity (CDC, 2014a). Freedom Industries, Inc., a producer and vendor of specialty chemical products, had acquired the storage facility where the spill occurred from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein & McWhirter, 2014). The spill site was located just over a mile upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a “Do Not Use” order was issued for all customers (WVAW, 2014a). With little information readily available regarding the potential human health effects of MCHM, the US Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the “Do Not Use” order remained in effect for a total of eight days, until January 17, when the WVAW distribution water was confirmed to have MCHM concentrations below this level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at concentrations as low as 0.55 ppb by individuals experienced in odor identification (Rosen et al., 2014); and even individuals with no such training can detect pure MCHM at just 7 ppb (WVTAP, 2014). The fact that this chemical can be sensed at such low levels – indeed far below those considered safe – undoubtedly added to growing public concern. In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until February 25 when MCHM levels were measured below 2 ppb (WVAWb, 2014), and eventually replaced the affected filter media (WVAWc, 2014)."

Jan 1, 2015

By K. Prashant Sarswat

Isotopes are critical to a variety of applications including physical science analyses, biology, medicine, pharmaceuticals, and national security. In most cases isotopes must be relatively pure or highly enriched before they become useful. Current isotope separation technologies are relatively inefficient, capital and labor intensive, and often produced by a limited number of suppliers. In the category of isotopes, lithium is among other important candidates. Lithium is found naturally in two isotopes, 6Li which accounts for 7.5% of all lithium, and 7Li which makes up the balance of 92.5%. Each of these isotopes is important to the nuclear industry. 7Li is often used in the form of lithium hydroxide which is used to control pH in pressurized water reactors. The current supply of 7Li is based mostly outside of the United States, and its long-term supply is uncertain. Apart from supply issues, the use of mercury for 7Li separation is also a concern in commercial processing using the most common and efficient approach [1–3]. Hence, a reliable, environmentally friendly, and efficient technique is needed to produce 7Li. In this line of investigations, the authors used a two-compartment system and significant separation was achieved. In this piece of research, some preliminary results are presented including cell design and actual isotope ratio after enrichment. Applying an electro-potential across two electrodes can be used to drive electromigration of Li isotopes. The electromigration is in addition to normal diffusion. Note that 6Li diffuses faster and hence there will be a lowering of the 6Li concentration near the positively charged electrode and an enhancement in 6Li near the negative electrode during the separation process. Similarly, 7Li will be more prevalent near the positive electrode and less prevalent near the negative electrode during the initial separation stage [1].

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By K. S. Liddell

The Kell Process has been developed for the extraction of platinum group metals (PGMs) and base metals from sulphide flotation concentrates. The process has been successfully tested on several different sulphide flotation concentrates, including those from the UG2 chromitite horizon and the Platreef mafic/ultramafic layer. It has been shown to provide high (>95 per cent) and selective extraction efficiencies for the key valuable metals, i.e. Pt, Pd, Rh, Au, Ni, Co, and Cu. The Kell Process consists of several commercially proven unit operations. S, Ni, Co, and Cu are first selectively removed by use of a pressure oxidation step during which the dissolution of PGMs is minimized. The residue from pressure oxidation is subjected to a thermal treatment to ensure efficient PGM recovery by subsequent chlorination. All the core steps are very similar to well-proven conventional unit operations in common use, as are the subsequent metal recovery steps to provide marketable end products. Typical metallurgical responses of flotation concentrates from UG2 and Platreef to the Kell Process are provided, and key outcomes of an energy comparison study with smelting are summarized in this paper. Kell presents a potentially substantial improvement in PGM concentrate processing technology, in terms of economics via much-reduced power costs, ease of processing, and various environmental benefits. It allows for the treatment of high-chromium low-grade 'dirty' concentrates, such as secondary concentrates from the platinum industry's 'mill-float-mill-float' (MF2) flotation circuits and concentrates from retreatment of tailings. It allows greater concentrate mass pulls, has higher tolerance to gangue intergrowths in concentrates, and its use can provide substantial increases in overall PGM recovery. Its adoption would be a step change in the platinum industry, and given the commercially proven unit operations embodied in the Kell Process, at much-reduced risk compared with other more experimental technologies. Since the initial process development work, significant improvements and refinements have been introduced as a result of further compre¬hensive testing and process modelling. Pilot-scale testing and engineering study work is in progress for several selected sites.

Jan 1, 2012

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By D. R. Willmer, E. J. Haas

As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to sitespecific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council’s Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization’s site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

Jan 1, 2016

By B Hiebl, J Martens, L Petzold

A research team at the Iron and Steelmaking department at Primetals Technologies has established new upgrading measures for improving the efficiency of the beneficiation process in ironmaking plants, relying largely on pre-existing equipment. After the upgrade, the iron content in the final iron ore concentrate was shown to be significantly higher. Remarkably, the costs for employing the respective measures are surprisingly low.This case study is based on a Kazakh iron and steel producer, whose beneficiation process is currently generating a magnetite concentrate with a final iron content of 65.65 per cent. The study shows that the implementation of Primetals Technologies’ intelligent modification measures to the current beneficiation process, the realisation of more effective dewatering, and the utilisation of an innovative binder lead to an increased iron content in the resulting pellets, reaching a concentration of 69.17 per cent (iron ore concentrate) and 66.5 per cent (pellets).The current operation consists of three closed circuit grinding stages, four stages of low intensity magnetic separation, vacuum disc filters and straight-grate pelletising. By dividing the slurry after the second stage of grinding and the third stage of low intensity magnetic separation, it is possible to divert the more iron-rich fines before they would enter the third grinding stage and the fourth stage of magnetic separation. This then reduces the load on the existing third stage ball mill. Afterwards, the ground material is treated in an additional low intensity magnetic separator and mixed with the previously diverted fraction of the fines. An improved filtration procedure, combined with the application of a highly sophisticated binder, further reduces the amount of additives needed, so that a genuine direct reduced (DR)-grade iron concentrate is produced as a result.All laboratory, pilot and pelletising test work was executed at Primetals Technologies’ laboratories in Austria.CITATION:Martens, J, Petzold, L and Hiebl, B, 2017. Enabling iron ore concentrate for the production of direct reduced iron with pre-existing beneficiation lines, in Proceedings Iron Ore 2017, pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017