Search Documents

By Leonard Obert

This report describes an inexpensive triaxial equipment for testing 2-1 / 8- , 4- , and 5-5 / 8 - inch - diameter rock cylinders subjected to loading conditions comparable to those encountered in underground mining . Only minimal specimen preparation is required . The maximum axial load that can be applied is 250,000 lb , which corresponds to an axial stress of 70,000 psi for the 2-1 /8- inch- diameter specimen . The maximum radial pressure that can be applied is the same for each specimen diameter ; namely , 10,000 psi . The mechanical parts in this equipment are relatively easy to machine and fabricate . The cost of all parts , including the 250,000- lb hydraulic press but not including labor costs , was approximately $ 1,000 .

Jan 1, 1963

By O. A. Ogunseitan

The contamination of aquatic ecosystems by mercury wastes is one of the most serious forms of environmental pollution associated with the metal mining and electrochemical industries. The transformation of inorganic mercury to alkylated species is a reversible bacterially-mediated process. The production of methylated mercury is of ?major public health and eco-toxicological concern because these forms of mercury are highly toxic ?and they bioaccumulate in aquatic organisms. We determined the response of the genetic determinants of mei:cury transrormation by Pseudomonas species (that predominate in contaminated soils and sediments), to the concentration and species? or available mercurfiations. By combining selective isolation and gene. ?probe techniques, the intrinsic genetic potential for mercury detoxification in a contaminated environment ?can be estimated. We determined that genetic units required for mericury volatilization (merA ?for mercuric reductase) are naturally amplified in response to mercury. Mercury-resistant bacteria that tolerate up to 100 ug Hg(Il)/ml of medium contain about 10 times more DNA fragments encoding merA than in unadapted bacteria. The exposure of bacteria to methylated.Hg (10 ug/ml lake water) produced increases (up to 10 times) in .genetic units, and higher levels of genetic expression (up to 50 times) per ml of lake water for the mercury reductase system, than on-induced lake water. The findings suggest that in environments where methylated Hg may accumulate as a result of bacterial activity, the reverse reaction which leads to the removal of mercury through volatilization from the system, may be achieved by inducing genetic ?amplification and expression of the mercuric reductase gene system.

Jan 1, 1991

By Nobuyoshi Yabuki

Building Information Modeling is a prevailing methodology in the building industry and half (by length) of the world's shield tunnels are in Japan. Accordingly, for shield tunnels from 2005 to 2007, we developed a product model called IFC-ShieldTunnel, which is based on Industry Foundation Classes (IFC), in order to meet the future demand for such a product model. IFC-ShieldTunnel was developed by adding new elements that are specific to shield tunnels and that are not included in the original IFC. The added elements include shafts, segments (A, B, and K types), waterproofing elements, segment joint elements, and ring joint elements. Furthermore, soil layers and void elements were created. Recently, we updated the product model by re-organizing the entities and correcting errors. We deployed the updated IFCShieldTunnel model in the construction of an actual shield tunnel in Tokyo for about a year from August 2010 in order to check its feasibility. In the verification process, first, segments were modeled using Autodesk Revit Structure 2011 and property data were assigned to each segment element. Next, a mapping between the original attributes of the entities of IFC and properties of IFC-ShieldTunnel segments was developed. Using this mapping and IFC?s IfcBuildingElementProxy function, we were able to convert the IFC data from Revit Structure 2011 to IFC-ShieldTunnel automatically. Segment data were also converted from Revit Structure to Google SketchUp by IFC-ShieldTunnel. Furthermore, the construction scheduling and cost data were converted from Revit Structure to EXCEL for 4D and 5D analyses of construction. We interviewed engineers who used IFC-ShieldTunnel and received positive comments about the utilization of the product model. Overall, our test demonstrated the feasibility of IFC-ShieldTunnel. In future work, we plan to apply IFC-ShieldTunnel to more projects and test its practicality.

Aug 1, 2013

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By S. Kauvosaari, M. Olofsson, O. Haavisto, M. Kosonen, J. Martikainen

The target in grinding circuit operation is usually to maximise the throughput and energy efficiency while keeping the product particle size on an optimal level for downstream operations. Furthermore, feed ore variations in size and hardness need to be compensated in order to stabilise the process. This is a challenging task for any circuit and requires good instrumentation, combined with careful control design. This study investigates the control of a two-stage iron ore grinding circuit with an AG and pebble mill at LKAB Kiruna KA3 concentrator in northern Sweden. A new control approach based on multivariable model predictive control (MPC) is designed, implemented and evaluated for the circuit. Additionally, advanced instrumentation including a volumetric charge measurement for grinding mills is utilised. The MPC control approach starts with step tests that are used to model the effect of manipulated variables (MVs) like feed rate, water addition and primary mill speed on controlled variables (CVs) such as final product particle size, power consumption and volumetric charge of the mills. In the control implementation phase, the models are then utilissed together with current process measurements and known operating limits to predict optimal future changes for the manipulated variables in order to reach the desired process output values. It is shown that the new control approach improves the stability of the circuit and reduces energy consumption. Keywords: Model predictive control, grinding, optimisation

Jan 1, 2020

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015

By W. H. Pomroy

This report describes research by the U.S. Bureau of Mines to design and in-mine test a rapid response pneumatic fire detection system for multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. The Bureau's prototype system is described, with emphasis on design features that counter commonly experienced and/or perceived operating problems with pneumatic detection systems. Finally, the results of a 3-year in-mine performance evaluation of the prototype system are discussed.

Jan 1, 1990

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By Greg Andrews, David Dreisinger

The Foxtrot deposit of Search Minerals contains a range of rare earth element containing minerals including allanite, fergusonite and bastnasite. The Search Minerals Direct Extraction Process for treating these minerals involves coarse crushing of the ore to -6 mesh (3.45 mm), acid treatment at 200 °C in a novel reactor configuration, water leaching, various purification steps to reject iron, aluminum and uranium/thorium (present in small amounts) and finally precipitation of rare earths as an oxalate and calcination to form a mixed rare earth oxide product for refining. The economics of the process are presented.

Mar 1, 2017

By R. C. Dunne, W. A. Gilbert, I. J. Corrans, K. S. Liddell

After bench-scale and pilot-plant tests in which it was shown that wet high-intensity magnetic separation (WHIMS) can achieve good recoveries of gold and uranium from Witwatersrand residues, a production size machine was installed at a gold mine. The mechanical and metallurgical performance of this machine have been satisfactory, and the economics of the process are attractive. WHIMS can be combined with other unit operations like flotation for the optimization of overall gold and uranium recoveries. This concept is shown to be relevant, not only to operations for the retreatment of tailings, but to processes for the treatment of coarser material. In the latter, there is a saving in energy consumption compared with the energy required for the fine grinding of the total feed, and a material suitable for underground backfill can be produced. Improved. more cost-effective WHIMS machines currently under development are also described.

Jan 1, 1983

By Jürgen Antrekowitsch, Thomas Griessacher

"Heavy metal containing residues are typically hazardous wastes because on the one hand, a deposition gets more and more complicated and on the other hand, the large amounts of metals like Zn, Cu, Fe and Pb represent a significant value. Thus, a post-treatment of these materials with the recovery/recycling of the metals and stabilization of the waste is not only ecological but often also economical. The therefore typically applied recycling processes utilize pyrometallurgical steps, where carbon or carbon monoxide from fossil coal and coke is used as a reducing agent, which results in large amounts of CO2 emissions. An alternative option is the application of a hydrogen-rich gas emitted in biomass utilization processes as a carbon-neutral reducing agent. Investigations in a retort process which were done at different temperatures and times showed excellent results concerning the achievable reduction rates and final contents of the heavy metals for various residues.IntroductionNowadays heavy metal containing residues like electric arc furnace dust (EAFD), dust from cupola furnaces, waelz slag, etc. are declared as hazardous wastes in a growing number of countries due to the leachability of the heavy metals in these residues. For that reason it is no longer possible to landfill these materials or use them for road construction or disposal works. Some land filling activities, carried out until now, have only been realizable because of some process modifications or cost intensive post-treatment steps of these residues. But the disposal capacities for such materials are decreasing, therefore increasing the prices. The second point for the growing disposal limitations is the stringent environmental legislations and regulations, which restrict the number and amounts of materials which can be dumped [1 – 5].From the other point of view these heavy metal containing residues usually have high contents of zinc, lead, iron, etc., which represent a significant value and therefore a big potential to recover these metals. This is why in recent years the number of recycling processes and the amount of recycled heavy metal containing residues have continuously increased. These recycling processes have the target to recover the valuable metals from the residual materials in the form of a saleable product as well as the stabilization of the slag produced in these processes [5, 6]."

Jan 1, 2011

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By Rajesh Sonkar, Sanjeev Kumar

The deployment of Dragline machines in opencast coal projects involves huge capital expenditure as well as operating costs. The mine operators always endeavor to ensure smooth excavation of material by the Dragline machines while meeting the major objectives of safety, minimal disturbance to environment and optimal operating costs. Optimization of fragmentation through well designed blasts is fundamental in meeting part of the objectives is good fragmentation of rock or mineral proposed to be lifted by the Dragline machine. If the overburden lying over mineral is not properly fragmented, it may result in formation of ‘Toe’ the removal of which is the most arduous task in opencast coal mines. The mine operators always endeavor to achieve best possible results in blasting to ensure smooth operation of the high cost Dragline Machine. However, despite continuous efforts by the blasting engineers involved in bench blasting for the machine, the formation of ‘Toe’ is an ever nagging problem faced in large opencast coal projects eventually reducing the overall operational efficiency of mining.

Jan 1, 2011

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Joseph Sabatini

This report, covering the period January through December 1975, contains abstracts of articles concerning all phases of cost engineering and economics for chemicals processing, raining, and other mineral industries. The abstracts are collected from the following sources: 1. Chemical Engineering 2. Chemical Engineering Progress 3. Chemtech 4. Coal Arse 5. Coal Mining and Processing 6. Combustion 7. Drilling 8. Electrical World 9. Engineering and Mining Journal

Jan 1, 1976

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

By J. S. Moretzsohn, D. F. Graham

"Airborne Synthetic Aperture Radar (SAR)was acquired over the Carajás Mineral Province, within the rainforests of the Amazon, which hosts the world’s largest Fe-ore deposit(Santos, 1986). Significant chemical weathering exists in this humid environment. PrevalentAu mineralization is thought to be generally associated with deformation zones in Archean schists.Radar data have proven to be very useful as an aid to geological mapping in the tropical rainforests of the Amazon Basin in Brazil. In these densely vegetated areas, a sense of regional structural trends is obtained as a con-sequence of the sensor/terrain geometry. The top forest canopy is the main terrain reflector of X-band radar energy, and consequently is the main terrain surface feature expressed in processed radar imagery. Radar is important for extending t,he continuity of mapped structural lineaments. Differential weathering is related to variations in radar image texture which is used to infer gross lithologic variations and relative age relationships of major rock units. Specifically, quartzites and banded iron formation are highlighted in the radar imagery due to their unique tonal and textural appearance, in contrast to schists, gneisses and metavolcanic rocks. As tropical areas are typically enveloped in cloud or mist, radar data are invaluable in providing information for logistical planning of field mapping activities."

Jan 1, 1997