Search Documents

By S. Kobayashi, N. Ohara, T. Aoki, S. Sakurai, M. Iwano, M. Shimo, I. Otsuka

"This project is the upgrading of a commuter line of approximately 76 km to improve the railway system in Istanbul metropolitan area. Railway tracks have been connected between Asia and Europe through a tunnel under the Bosphorus Strait. The length of these underground structures sums up 13.6 km. In this paper, the observational construction management based on field measurement performed at large scale underground railway station (Sirkeci station) constructed by means of New Austrian Tunneling Method (NATM) is described and the mechanism for generation of ground surface settlement above this station is discussed.Buildings above Sirkeci station are overcrowded. About 60% of the buildings are made of reinforced-concrete (RC) and others are of brick. Based on the investigation into the predicted settlement and inclination, necessary actions such as structural reinforcement and soil improvement have been conducted for dilapidated buildings.Rock mass around Sirkeci station consists of alternative strata of sandstone and mudstone. It is overall soft rock with an elastic modulus of 150 MPa, partly including fractured zones. Overburden is about 30 to 40 m. The thickness of unconsolidated sand layer distributed on the bedrock is about 10 m. As a result of in-situ permeability tests, the coefficient of permeability of the sand layer is about 1.0x10-3 cm/s. Fill layer of about 10 to 25 m in thickness covers the sand layer at the ground surface. The fill layer contains a lot of artificial waste like splinters of wood, brick chips and mortar chips, etc. in addition to gravel, sand, silt and shells. The coefficient of permeability of fill layer is estimated to be 1.0 x10-2 cm/s, which is one-order greater than that of the sand layer. Fill layer consists of ancient city ruins of ages respectively from the Eastern Roman Empire, the Byzantine Empire and the Ottoman Empire and has a lot of gaps.The underground part of the Sirkeci station was excavated through a ventilation shaft. Ground surface settlement occurred more than predicted. Therefore, back analyses were performed in order to precisely predict the next-step settlement. However, back analyses with elasto-plastic models could not simulate the actual phenomena and hence, an anisotropic-damage-parameter model developed by Sakurai (1999) was adopted for the back analysis. Furthermore, as the excavation of tunnel proceeded, the ground surface settlement exceeded the predicted value again. Based on the monitoring results, it seemed that pore water pressure decreased by the tunnel excavation resulted in the soft rock and soil to be contracted due to the increase in the effective confining pressure. A coupled hydraulic-mechanical analysis was applied to explain the relationship between decreased pore water pressure and ground surface settlement. The settlement due to drainage from tunnel wall was well-estimated in the coupled hydraulic-mechanical analysis.However, further settlement occurred more than predicted again and again. Though it was very difficult to clarify the reason of the large settlement, it was recognized that the unexpected ground surface settlement resulted from the existence of the large gaps in the fill layer that was greatly compressed. The final settlement reached up to 327 mm."

Jan 1, 2015

By William J. Campbell

This Bureau of Mines report describes a study conducted to determine the relationship of mineral habit to particle size and shape characteristics for prismatic, acicular, fibrous, and asbestiform varieties of tremolite. Particle measurements were made with the petrographic microscope at X 1,250 and the scanning electron microscope at magnifications up to X 10,000. All of the varieties of tremolite, upon Wiley milling, produced a significant percentage of particles that meet the Federal regulatory criteria for counting as asbestos fibers. However, only the asbestiform variety gave milled particles that fell into a size range of >10 µm in length and <0.5 µm in width; some medical scientists consider this range significant for production of adverse health effects.

Jan 1, 1979

By H. W. Kasaini, E. Bourricaudy, T. Larochelle

Rare Element Resources Inc., a U.S. based company, has developed a three-stage process for producing a +98% mixed REO powder from hard rock feedstock (-48 mesh, 2.9-4.8% REO) consisting of bastnaesite and ancylite minerals. Firstly, the whole ore is digested in chloride media at low temperature in counter-current flow mode. Secondly, the rare earths (REEs) are selectively precipitated as oxalates directly from an impure pregnant leach solution (PLS). Finally, significant amounts of free acid and water are recovered from the REE-depleted filtrate and subsequently recycled within the process. Excess heat from the oxalate calcination process is captured and reused in the plant. Due to the low leach temperature (45 ºC) and moderate acid dosage (240-297 kg/t, HCl), rare earth oxides (REOs) are preferentially leached out of fine solids leaving most of the base metals (Ba, Fe, and Al ) in the residue. Selective recovery of REEs from the PLS is achieved by mixing dilute oxalic acid (33% H2C2O4) and PLS at elevated temperature (85-95 ºC). The REEs plus thorium are precipitated as oxalates (REE2 (C2O4).xH2O) while the base metals are left behind in the barren filtrate. Multiple batch and pilot test results have confirmed that 50-80% of the oxalic acid can be recovered from the REE-depleted PLS through low-temperature crystallization (10-15 ºC). Typical leach efficiencies of critical rare earths at 45 ºC range from 85-99% (average 93%) while oxalate precipitation at high temperature increases the crystal size of RE oxalates (>450 microns, d80) thereby improving filtration. The economic benefits of this process include elimination of flotation and magnetic separation Capex and driving hydrometallurgical Opex down to $6- 7/kg, REO produced. As part of a comprehensive risk mitigation strategy, Rare Element Resources Inc has operated multiple pilot plants at SGS in Lakefield, Ontario, Canada to optimize counter-current leaching (CCL), REE oxalate precipitation (OXP), and thorium removal circuits. This paper presents pilot testing data from CCL and REE OXP circuits.

Jan 1, 2016

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By Guillermo Turner-Saad

"Best practice in the economic evaluation of mining projects and operations is based on the integration of geological, mining, metallurgical, environmental, marketing, economic and corporate information and strategies. Fundamentally, the economic evaluation takes into account mining, blending, stockpiling, processing, smelting, refining and marketing ore resources with grades estimated by geostatistical methodologies.Nevertheless, a realistic economic evaluation consists of a concurrent and integrated optimization process that maximizes the concentrates or products of liberated and selected ore minerals from mineral deposits. The optimum solution is obtained through a trade-off among mining, blending, stockpiling and processing ore reserves with distinct mineralogy and texture characteristics. The concurrent optimization determines both the practical mining sequence of ore reserves and the dynamic and robust mineral processing flowsheet design over the expected life of mining projects and operations.A combined risk-adverse and concurrent optimization process takes into account the spatial uncertainty of the mineralogy and texture characteristics of ore reserves. Additionally, a variety of mineral processing linear, non-linear, additive and non-additive parameters modeled spatially. The spatial uncertainty of these ore reserves characteristics and parameters has a direct impact in the expected mining sequence, mineral processing flowsheet design, concentrates or products quantity and quality, and economic value of mining projects and operations.Geometallurgical domain constrained stochastic geostatistical methodologies and multivariate mathematical models are applied for spatial uncertainty modeling of ore reserves characteristics and parameters. These mathematical models correlate the mineral processing liberation and selectivity responses of the mineralogy and textures within each geometallurgical domain. These models, in turn, are defined based on results of mineral processing and environmental testwork of unbiased and representative samples chosen for their variability. These samples are selected within mutually exclusive spatial geometallurgical uncertainty domains with similar mineralogical and textural characteristics in mineral deposits.Geometallurgical domains are defined by applying and combining multivariate statistical analysis and implicit modeling methodologies. These involve determining and constraining mineral processing liberation and selectivity properties explicitly contained in the extensive and integrated exploration drillhole database."

Jan 1, 2010

By Harold S. Morgan

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is being developed in southeastern New Mexico by the United States Department of Energy as a research and development (R&D) facility to demonstrate the safe disposal in salt of radioactive wastes resulting from defense activities. As part of the WIPP R&D program, a series of in situ tests will be performed to determine the behavior of drifts and storage rooms in the creeping salt medium (Matalucci, et al. 1982). Data obtained in these tests will be used to evaluate and improve numerical models used to compute the structural response of these drifts and rooms. Stress has been proposed as one of the parameters to be measured in the tests, and borehole inclusion stressmeters have been included in the instrumentation package. Cages of this type provide an indirect measurement of stress change in that they actually monitor borehole displacements which are then related to changes in the in situ stress away from the borehole. The relationship between stress and displacement is highly dependent upon the constitutive behavior of the rock in which the gage is emplaced. This relationship is well understood for rocks with linear stress-strain behavior (Fossum, et al, 1976), but, for creeping rocks like salt, the relationship has yet to be determined. Thus, inclusion gage response in salt must be investigated fully before stress measurements from the WIPP in situ tests can be used for comparisons with computed stresses The calculations presented in this paper were performed as part of an investigation of inclusion stressmeter performance in salt. They focus on the strain gaged stressmeter (SGS) (Cook and Ames, 1979) and on a hypothetical solid cylindrical inclusion with variable stiffness Issues addressed include the effects of creep and the effects of gage stiffness on stressmeter output for various loading conditions. The

Jan 1, 1984

By John C. Niedzielski

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site?s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The full-scale field test played a significant role in the design of the project?s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

By William O. Vanderburg

The fluorescence of many minerals, when excited by different wave lengths, of ultraviolet radiation, has long been recognized as a spectacular laboratory phenomenon. Since the original display in the British Museum, the phenomenon has been used frequently for educational purposes and public demonstrations. Its practical application for the rapid detection of certain minerals in ores and mill products at the zinc mine at Franklin, N. J., has been described.3 Due to technical improvements in ultraviolet-radiation apparatus, fluorescence has found a new field of application in the tungsten-minim; industry. Although fluorescence of scheelite (calcium tungstate) has been known for a number of years, the practical application of the phenomenon is the outgrowth of a program of cooperative research conducted by Ott F. Heizer, manager of the Nevada-Massachusetts Co., Inc. , Mill City, Nev., and Dr. Paul F. Kerr of Columbia University. Special portable lights for fluorescing scheelite have been developed and utilized in underground geological work. Thanks are due Ott F. Heizer for permission to publish data included in this paper.

Jan 1, 1935

By Gram Curtis

The apparatus described below for the handling of plates upon their delivery from the rolls, embodies features believed to be of interest to those contemplating the building of new plate-mills, and also to such owners of existing mills as may be considering the improvement of their works. The points to which attention is called are the small space required for the finishing-end of the mill, and consequently the very moderate size of the building for the amount of plates handled; the directness and ease of manipulation, and therefore the mall amount of labor required; the distribution of plates; the facilities and time allowed for their cooling. These, together with other features of detail and general arrangement scarcely less important, will become apparent when the descriptions and illustrations herewith given are understood. As these devices deal with the finishing of the plates only, they may be added to any plate-train when the floor-space and the building are large enough to permit their introduction; and it will be obvious that the features of this method, more or less modified, are applicable to any existing mill. Figs. 1 and 2 show a three-high 32-and 19- by 120-inch Lauth mill, with hydraulic lifting-tables, served by four heating-furnaces, with hydraulic cranes for charging and drawing. Upon leaving the rolls, the plate is allowed to rest with its forward edge projecting somewhat beyond the end of the catcher&apos;s table. Here it is seized by the automatic tongs, A, suspended from a buggy travelling in the overhead trough, B, and actuated by the hydraulic cylinder, C. These tongs are operated by a boy, who stands several feet from the heated plate, and controls the long light handle, D, shown in the plan, Fig. I. His duty is merely to advance the tongs by means of .the hydrulic cylinder, C, to raise or

Jan 1, 1892

By O. Guyot, T. Mulpeter

Sadiola Hill mine is located in the sub-Saharan part of Mali. In its first two years of operations, Sadiola Hill mine had already exceeded expectations with respect to profitability, plant capacity, metallurgical recovery, cash costs and social integration into the area. The advanced control system installed by the authors has been a major contributor in the substantial throughput of the mill over the design tonnage with no loss of recovery. The run-of-mine ore at Sadiola consists of soft clays with a varying percentage of grit, producing a high viscosity slurry. The percentage of grit fed to the plant varies on an hourly basis. This combination was expected to have a large impact on the milling circuit and determined that the early installation of an expert mill control system would be advantageous. Svedala Cisa OCS©, was selected as the most suitable support software. The operational rules and control philosophy are housed in the OCS© graphic-oriented fuzzy expert system while a model­based Soft Sensor has the remarkable ability to detect the variations in grit in the feed. Designed during the second half of 1996, commissioning of the system began in March 1997, the OCS was fully on-line by September. With the implementation of the optimising control strategy a throughput of 5.0 million tons relative to the target of 4.4 million tons was achieved for the 1998-operating year. The Sadiola project confirms that advanced process control techniques are among the most cost-and time-effective methods of improving metallurgical plant performance. The recipe that worked at Sadiola is a mix of metallurgical expertise, proper software selection, adequate design of control philosophy, and excellent plant support and follow­up. The early decision, design and installation of the mill control system has resulted in an enhanced Return on Investment.

Jan 1, 2000

By Will H. Coghill

Recent work on beneficiation of the .Alabama red iron ores and ferruginous sandstones has brought out interesting new facts on particle-size reduction that axe a valuable supplement to what is already known.4/ The work was done by the Southern Experiment Station of the Bureau of Mines in cooperation with the University of Alabama, University, Ala., on two samples from the Birmingham district. One was an oolitic red iron ore containing about 35 percent iron; the other was a ferruginous sandstone containing about 25 percent iron, particularly attractive because of its low phosphorus content. In both samples rounded quartz (sand) grains were embedded in an oolitie, "onion skin" matrix of hematite. The hematite carries varying amounts of clay,-which limits the grade of concentrate that can be made. The clayey hematite is soft, so that the rock crumbles readily under pressure. The sand grains shell out like corn,, and without much exaggeration the mill used for differential grinding might be called a "sheller,"

Jan 1, 1940

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By A. H. Mokken, G. K. I. Blendulf, G. J. C. Young

A study of the arrangements for pulp discharge on pebble mills, and their influence on mill performance by A. H. MOKKEN, B.Sc. (Eng.) (Rand) (Fellow), G. K. I. BLENDULF, M.Sc. (Stockholm) (Member), and G. J. C. YOUNG, B.Sc. (London) (Member) Although used for many years in the gold-mining industry, the conventional pan lifter at the discharge end of a pebble mill has hindered attempts at optimization of speed of rotation and pulp flow. A theoretical approach to flow patterns in pan lifters has pointed to limitations in the capacity of these lifters, with capacity decreasing as speed of rotation is increased. Complete elimination of the pan lifter by the adoption of peripheral or end discharge has resulted in a marked increase in pulp flow and an improvement in power utilization. Assays of the gold content of pulp discharged after a mill stoppage from mills fitted with pan lifters show values well in excess of the current milled grade, which indicates an accumulation of gold particles in the mill and, therefore, a longer retention period. The same could apply to other heavy minerals and metals present in the ore feed or worn off mill linings and metallic grinding media. Examples are osmiridium, fine iron and iron alloys, and copper and sulphide minerals. This phenomenon is attributed to the higher specific gravities of these metals and minerals, causing them to migrate towards the mill shell, from which position they are not readily removed by the lifters at the discharge end of the mill. The close association of gold particles with iron and sulphide minerals in the crevices of mill liners might be conducive to the formation of coatings on the gold. Assays of samples of milled pulp taken from a mill designed for end discharge show a lower accumulation of gold. The accumulation and nature of these gold particles are being studied at present. With increasing diameters of pebble (or autogenous) mills, peripheral or end discharge appears to be the preferred method of pulp removal.

Jan 5, 1975

Heap leaching with thiosulfate is only used in one location for the treatment of a refractory preg-robbing gold ore initially pre-treated with bio-oxidation. The chemistry of thiosulfate leaching is complex. Further work is required to develop a better control of the system. A mild refractory gold ore containing pyrite and chalcopyrite was used in this study to investigate the use of thiosulfate as an alternative heap leaching technology. Preliminary bottle rolls tests indicated that similar gold extraction was obtained with cyanide and thiosulfate. In the column leach test, effects of thiosulfate, copper and ammonia concentrations, and their ratio on both gold extraction and reagent consumption, were assessed. The range of reagent concentration were: 0.1 - 1.0M (NH4)2S2O3, 0.03 - 0.10M CuSO4*5H2O, 1.0 - 6.0M NH4OH. The solid-liquid ratio was in the range of 0.83:1 to 5: 1. Best results showed that 72% of gold was extracted in 50 days with 0.3M (NH4)2S2O3, 0.05M CuSO4*5H2O and 6M NH4OH or a combination of 1.0M (NH4)2S2O3, 0.03M CuSO4*5H2O and 3M NH4OH. The reagent consumption at solid/liquid ratio of 3:1 was 37 - 48.6 kg/t (NH4)2S2O3 and 0 - 0.62 kg/t CuSO4*5H2O. The results of thiosulfate leaching were also compared with cyanide leaching.

Jan 1, 1999

Palabora Mining Company is operating a copper block cave mine in the Limpopo Province of South Africa. The mine was developed in the late nineties with a target ore reserve of 220 million tonnes of carbonatite at 0.69% copper. At 30,000 tonnes per day the operation had an estimated life of mine of approximately 23 years. Cave induced open pit side wall failure occurred in late 2004 with 130 million tonnes of waste reporting to the bottom of the open pit. This failure resulted in potential sterilization and dilution of the ore reserve and subsequent reduction in life of mine. Physical and numerical modelling indicated potential losses of up to 30% of the original ore reserves. Cave Management tools based on throughput principles are utilized to manage the failed waste ingress and ensure an optimum life of mine. Extracting the maximum rate possible, as soon as draw points are commissioned, with the view of achieving the highest production in the short term, is any mining operation?s goal as more money is required sooner. This approach, of course, improves the cash flow but presents a risk in the cave propagation profile as overall draw control is compromised. At Palabora it is evident from a Mineral Resource Throughput Management (MRTM) point of view that maximum production in the short term is not the solution. If high production rates are achieved and the profile of the cave is not manage correctly, this results in failed waste reporting to draw points earlier with adverse effects on grade. This would effectively and significantly shorten Palabora?s Life of Mine. The applications of good MRTM principles are required to assist the value chain for sustained profitability. The process commenced with change management paving the way for a better understanding and a holistic view for all role players.

Jan 1, 2007

By D. Limpitlaw, A. Alsum, D. Neale

"Ecological footprint analysis (EFA) was first described in 1996 as a measure of carrying capacity appropriated by human activities. EFA is a resource and emissions accounting tool designed to track the demand on the biosphere’s regenerative capacity. Ecological footprints are increasingly used as indicators of organizational and corporate environmental performance and product sustainability. There is a compelling argument to develop an EFA tool for mining companies.To determine the size of a mine’s ecological footprint, land requirements for all categories of consumption and waste discharge must be summed. This land is only made up of the ecologically productive land and water in various classes (cropland, pasture, forests etc.) required on an ongoing basis to provide all energy and material resources consumed and absorb wastes.A challenge in conducting an EFA for a mine is the shortage of accessible data. Undertaking an EFA for a corporation or individual site entails compiling consumption and emissions data (which can be used for other reporting applications). The footprint results themselves highlight the most critical aspects of an organization’s impact on the environment and provide a platform for focusing actions and for educating the workforce to improve their contribution to best-practice operations. This paper discusses the benefits and challenges of undertaking an EFA for a mining company, and provides examples of the various components of ecological footprints associated with mines, as well as showing how an EFA can be used to understand and communicate some of the impacts associated with mining activities.IntroductionFundamental biophysical and economic limits are now being experienced in many countries around the world. Herman Daly, a former World Bank economist, described this scenario as ‘uneconomic growth’, where the costs of growth exceed the benefits (Daly, 2005). This occurs when the economy’s expansion encroaches excessively on the surrounding ecosystem, sacrificing natural capital. Under such conditions the sacrificed natural capital is more valuable that the resulting economic growth. Consequently, the world faces largescale threats to sustainability and especially to the viability and continued existence of the ecosystems that support human settlements (El Zein et al., 2014). In recognition of this sustainability imperative, mining companies are increasingly concerned with their ecological footprint (EF)."

Jan 1, 2017

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

Does coal mining get enough out of its people?. In a number of cases, Yes. Several companies have rethought their management systems and accordingly are improving their utilisation of people to improve productivity. For some, capital and technology are the panacea for improved productivity and lower costs. Computerised mine planning, improved beneficiation processes, heftier longwall equipment, bigger trucks and shovels and upgraded coal clearance systems are expected to provide the answers.Whilst these factors are important they only contribute to part of the productive potential of a mining operation. Production flexibility provided by recent Industry award changes has brought about increases in total output. However, these improvements have not been matched by corresponding decreases in the unit cost of production.

Jan 1, 1991

By C. E. Abbey, M. S. Moats

It is well known that the addition of cobalt to copper sulfate — sulfuric acid electrolytes decreases the overpotential for oxygen evolution and decreases the rate of corrosion of Pb–Ca–Sn anodes. This effect, however, has not been ade- quately quanti fied in the presence of iron and manganese in this type of electrolyte. This work provides quanti fiable data on the effect of cobalt concentration in the range of 0 –0.6 g/L in synthetic electrowinning electrolytes with and without the presence of iron. The effect of cobalt on anode potential was determined using 2 and 24 h chronopotentiometry experiments. As expected, Pb–Ca–Sn potentials increased with decreasing cobalt concentration over the range of 0–0.6 g/L Co with and without the presence of Fe. Two regression models were developed to allow plant operations the ability to predict anode potentials as a function of cobalt concentration with or without iron in the electrolyte.

Mar 1, 2017