Search Documents

Slurry technology developed for the marine transport of mineral commodities has been increasingly applied to on-shore slurry transport systems. Reclaim of mineral concentrates, sand tailings for mine backfill and various industrial minerals from storage tanks or ponds normally require a slurry of high density at constant flow rates to improve process performance and to reduce handling costs. An efficient system must accomplish this at minimum capital costs with maximum reliability. Continuing improvements in equipment design to improve repulping efficiency and their application are discussed.

Jan 1, 1986

By Harrison Souder

MAGNETITE mining and milling in the Eastern States showed continuing improvement during the year. Some of the smaller mines remained idle, but the larger operations responded promptly to the improved situation in the iron and steel industry. The output of ore for 1936 was over twice that for 1935. A number of improvements were made in mine plant and equipment, and operating forces were increased and maintained at near normal. The coming year should see additional mines started up and production increased at the larger properties.

Jan 1, 1937

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

Experience has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. Test MAteriaIs Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It mas found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended On the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as One eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from goo°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal com-position was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical propertties and certain bearing properties of this alloy are described in the present paper Preparation of Compacts Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition~ 25 per cent nickel; 7 silicon; 3 phosphorus 64 copper. This alloy is brittle in the cast condition and can be readily powdered. Sintering Procedure The blended powders were pressed at '5 to 40 tons per sq' in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By F. J. A. van Ruitenbeek, M. Dalm

In the presented study test work was performed with near-infrared hyperspectral imagery (NIR-HI) on 36 ore samples from a South-American epithermal Au-Ag mine. The aim of the test work was to investigate if NIR-HI provides information about the alteration mineralogy of samples that can be used to predict their economic value. Mineral distribution maps were produced from the hyperspectral images by using correlation coefficients between the image pixels and a set of reference spectra. These maps showed that detection of mineralogy with NIR-HI can be used to distinguish; i) ore particles with low Au and Ag grades, ii) ore particles with high carbon contents, iii) ore particles with high sulphur contents.

Jan 1, 2015

By K. Fair

Using an agitated column 203 mm (8") diameter by 1829 mm (72") tall with independent agitation units for the gas dispersion zone and the collection zones, respectively, permitted the independent evaluation of the attachment and the detachment mechanisms for the chalcopyrite/ silica system. Three particle size fractions were used in this study, i.e. coarse (+75 µ m), intermediate (-75 µ m + 10 µ m) and fines (-10 µ m). The optimum selection of the two agitation zones for the three particle size fractions were determined as a function of grade, recovery, residence time and air superficial gas velocity.

Jan 1, 1990

Drilling is a common process in mining and petroleum engineering applications which have different objectives. For example, drilling deep boreholes in tight gas formations and gas shales is becoming more popular in the oil and gas industry. By contrast, drilling deep small sized holes for mineral exploration in hard rocks is performed to obtain samples for grade analysis purposes. In both applications optimising the drilling process includes using the most effective operating parameters such as rotation speed and weight-on-bit in order to maximise the rate of penetration. Obtaining the optimum drilling parameters requires sensitivity analysis over a range of data, which would be costly and time consuming during real field operations. Therefore, conducting several experimental simulations in the lab would be very beneficial before field operations begin. A drilling rig was designed and developed to simulate various drilling scenarios. The rig works in conjunction with an existing true triaxial stress cell (TTSC) which is in use for different petroleum related applications. The rig allows drilling into a cubic rock sample of up to 300 mm size. Three independent stresses can be applied to the sample to simulate real in-situ field stress conditions while the sample may be saturated with fluid. A significant feature of the rig is its ultra-high speed rotation which can rotate up to 8000 rpm: this is to simulate hard rock drilling for mineral exploration applications where large weight-onbit could damage the bit cutters. With the proposed design, a drilling fluid of any type can be circulated in the simulated borehole similar to the real situation, to study its effect on drilling performance. The TTSC drilling lid is equipped with torque and drag measurement systems which are two important drilling parameters to be recorded during drilling operation. It is believed that this new drilling rig will open opportunities for performing major new applied research in the area of more efficient drilling in both oil and gas bearing formations and mineral exploration applications.

Aug 1, 2013

By A J. Cornah

"The mine geologist’s role in classifying ore from waste during grade control represents a critical link in the mining value chain. Any improvement in the ore/waste selection success rate (thus reduction in misclassification) which can be delivered by the mine geologist represents a value proposition. Improvement achieved without additional operating cost (for example extra drilling and sampling) will directly and immediately add value to the mining operation and therefore clearly must be pursued. Such improvement may be leveraged from existing resource drilling data which are typically less numerous but better quality than the grade control data. They are usually excluded from grade control estimates (termed the ‘base case’ approach here) because of the differences in quality.Various specialised geostatistical tools are available to account for differences in precision and accuracy between data sources during spatial estimation. This paper uses a conditional simulation (CS) case study to assess the benefit of integrating resource data into grade control estimates through ordinary kriging (OK) of pooled data sets, cokriging (CK), and ordinary kriging with variance of measurement error (OKVME) when the grade control data are:unbiased but increasingly imprecisebiased and increasingly imprecise. The premise assumed is that the resource data are unbiased and precise.The paper demonstrates that, if appropriately handled, resource data may be used to improve grade control estimates and thus improve ore/waste selection success without additional operating cost. Where grade control data are imprecise but unbiased it is recommended to integrate resource data using OKVME. This re-appropriates kriging weights from less precise to more precise data locations and improves the grade control estimation precision compared to the base case; it consequently provides an improvement in the grade control selection success rate. If grade control data are associated with significant bias, integration through CK is recommended as the biased data are zero sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case and consequently improvement in the ore/waste selection success rate.CITATION:Cornah, A J, 2014. Incremental improvement of grade control models using resource data, in Proceedings Ninth International Mining Geology Conference 2014 , pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By R Bose, M Bovell, G Cheong

Grinding media is a major consumable in mineral processing and therefore decreasing costs associated with its consumption is regularly considered a key goal for the minerals processing industry. Grinding media manufacturers have historically developed steels with improved wear life for their products as a way of delivering incremental media quality improvement. This has included increasing carbon levels from low-to-medium carbon steels up to the eutectoid carbon composition of 0.77% where the relationship between higher carbon and better wear performance is well understood. Producers today will regularly use grades in excess of 0.8% to further improve wear performance particularly for rolled grinding media.This paper first introduces the demonstrated relationship between this increased carbon content and improved wear resistance along with metallurgical rationale behind the high carbon production process and limitations. To test the performance improvement associated with the higher carbon steel grade, a series of Marked Ball Wear Tests (MBWT) were carried out. This paper also explores the relationship between ball properties, test methodology and wear performance and concludes by correlating increased carbon grade with a reduced consumption rate of between 3.1% and 6.1% in the tests conducted.CITATION:Bovell, M, Bose, R and Cheong, G, 2018. Improved forged grinding media performance with carbon content greater than 1.0%, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 559–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

A comparison of gold, platinum and sulfide ion selective electrodes was made in this investigation for determination of Eh in solutions containing sulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. In addition, the sensitivity of each electrode towards changes in sulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration of sulfide ions. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion, HS-, concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion, S-, activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of sulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1990

By Z. Zhang, M. S. Gonzalez, M. de P. Bueno, P. Holopainen, S. Luukkanen

"Despite being a field of study that requires practical knowledge and experience, mining engineering education follows the same pattern in most mining universities around the world, consisting of theoretical courses and laboratory-based practical modules (Mischo, 2015). The possibility of having practical training in real mining conditions on actual mine sites or processing plants is limited, while the only contact that undergraduate students have with mining operations during their time of study is usually through shorttime internships or visits in the context of educational trips. Real integration between universities and the mining industry may be scarce, which does not help students to observe the actual processes and thus understand the whole picture of mining operations.Indirect practical training is now possible since that technology is shifting from mechanical to digital, and the use of virtual reality — in the context of Mining 4.0 — can provide additional experience to the learning process. However, virtual reality is limited to the visual impression and is also limited in actions (Binder et al., 2018). In any case, when there is not a proper pragmatic view of how the different disciplines link to each other, especially if there is a lack of communication, unfortunately the results could be seen at a later stage in the mines as a poor performance of professionals and workers.Another major challenge for educating specialists in the mining sector is that experimental mines suitable for practical education, where the skills and knowhow could be developed and/or enhanced, are rare worldwide. Such research and educational (R&E) facilities are practically former metal ore mines that have been transformed into experimental sites. Besides being limited in number, not all facilities of this kind serve both a research and educational purpose.An early example of asolely experimental mines is the Luossavaara-Kiirunavaara Mine site operated by LKAB in Sweden, where systematic research on rock mechanics and mining engineering was successfully carried out in the 1980s. As a result, the developed underground mining technology was applied in LKAB’s mines at a later stage. There have also been research mines within collieries such as the former Lake Macquarie Mine at New South Wales in Australia and the Zeche Tremonia Mine in Germany), but these are no longer in operation (Mischo, 2015)."

Oct 1, 2019

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By Ruixuan Zhang, Yan Li, Shusen Cheng

The measurement of raceway temperature in the blast furnace is a critical issue, which is very significant for judgment of, prediction and diagnosis of the racewa yburning state. This paper deals with mathematical models by Monte Carlo method to approximately simulate the radiation heat transfer in the race-way and establish matrix equations using CCD cameras, which are solved to obtain the three-dimensional temperature field. Due to the existence of fluctuation error, CCD camera measurement error and others,this is analyzed and random error is added in the measurement data to demonstrate the effectiveness and stability of the reconstructed temperature field. The results show that the reconstructed three-dimensional temperature field of the raceway is very close to the exact temperature.

Mar 1, 2017

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;' these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.' Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958