Search Documents

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By Daniel G. DiCanio

Investigation of the costs of industrial accidents dates back to the 1920s. The Bureau of Mines was one of the pioneers in accident cost investigation with numerous studies published between 1928 and 1933. The bulk of these early investigations dealt only with costs which appeared as payouts on company books; that is, the direct cost of insurance premiums and the costs of medical expenses which resulted from industrial accidents. These early investigations, especially the Bureau's study of accident costs in Pennsylvania and Indiana coal mines provided the first real evidence that promotion of industrial safety pays back in dollars as well as in human life and wellbeing. In the 30s and 40s, investigations began to accumulate evidence that industrial accidents impacted more than just the direct operating expenses of a company (i.e., higher insurance premiums). The work of Heinrich pioneered these investigations, and produced strong evidence that the un¬insured costs of accidents far outweighed those costs covered by insurance. Heinrich developed and published a ratio of insured to uninsured costs of 1.4. Despite his cautionary statements about blanket application of this ratio it is used even today to estimate total costs of accidents. Simonds, in the late 40s and early 50s, extended the definitions of uninsured or indirect accident costs and developed what is now regarded as the principal method for estimating the total economic impact of industrial accidents. Simonds' method served as the basis for development of the logic of the Accident Cost Indicator Model (ACIM). However, several departures from Simonds' method were made to satisfy certain requirements imposed by the Bureau of Mines, and because information gathered during the course of our investigation justified a departure. These departures are noted in the discussion which follows.

Jan 1, 1977

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Thiago Pinto Silva, Leandro Rocha Lemos, Luiz Fernando Andrade de Castro

This paper shows an evaluation about effect of dispersant sodium silicate along to limestone, in the form of pulp, on the cold agglomeration process for iron ore sintering. Before that, it was verified the effect of pH, solids content and amount of dispersant on the stability of the system (limestone, water and sodium silicate). It was found that the lower the solids content, the more alkaline pH and the amount of sodium silicate equal to 20 l for each 1t of limestone, was the level of dispersion of the system. The influence of the limestone pulp with dispersant depended on the granulometry of the ore mixture and the type of technological route. For the thinner type (42,8% <0.15mm), the limestone pulp with dispersant reduced the resistance of the adherent layer of the cold agglomerates, regardless of the technological route. However, for the coarser type (24,7% <0.15mm), the limestone pulp with dispersant increased the average size of the aggregates, preserving the resistance of the adherent layer when manufacturing with two intensive mixers in series.

Oct 1, 2019

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By S. A. Ghoreishi-Madiseh, F. P. Hassani, H. Rafezi, H. R. Manouchehri, A. Shadic, A. P. Sasmito

Weakening rocks by taking advantage of microwave-induced microcracks is a promising solution for comminution processes. This paper investigates the effects of microwave treatment of the rock/or samples in single and multi-mode cavities. Based on the experimental results of using a 2.45 GHz microwave generator, the performance of different cavity setups and their impact on the energy effectiveness of the microwave irradiation was examined. Physical interpretations were drawn from multiple experiments with a relatively wide range of power rates and exposure times. Both basalt and kimberlite samples were used in experiments, and their results were systematically compared. For single-mode cavity tests, a microwave applicator waveguide antenna was placed at different distances from the samples to evaluate the effects of sample positioning on microwave heating, both numerically and experimentally. Eventually, cavity performance was assessed by using calorimetric test results, and strength decay was documented based on the spallation of the samples. It was found that the singlemode cavity setup has unique properties that can significantly improve the electromagnetic heating and therefore, strength degradation process. Keywords: Microwave, fragmentation, energy effectiveness, calorimetry, mine-to-mill

Jan 1, 2020

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

In a world where declining ore grades are increasingly common, it has become necessary to process low-grade feedstock. Carbothermic reduction in the presence of alkali (Na2CO3) has been adapted to beneficiate waste that contains titaniferous minerals (TiO2 ca. 12 wt%), in order to recover valuable constituents such as TiO2, Fe and V2O5. The waste from vanadium metal processing has environmental legacy as it leaves nearly 1 wt% V2O5 process waste, which is environmentally problematic due to V5+ ions in contact with water and soil. This investigation focuses on the kinetics and mechanism for alkali reduction of mineral waste bearing 10–12 wt% TiO2, which we studied in the 1073–1323 K range. The thermogravimetric analysis (TGA) technique was used to record weight loss data. Two distinct regimes demonstrated mixed-control kinetics: (1) at low temperatures the activation energy was found to be 199 kJ mol−1, which corresponds to the outward diffusion of O2− ions; and (2) at high temperatures the calculated value was 130 kJ mol−1, which is consistent with the activation energy for the outward diffusion of Fe2+ ions. The metallic iron, sodium titanate and sodium aluminosilicate phases that formed were characterised using X-ray powder diffraction (XPRD) and scanning electron microscopy (SEM) techniques, and their significance for metal recovery is explained.

Mar 1, 2017

By L Bartsch, M Kelahan, E Wingate, J-S David

The use of column flotation cells for recovery of phosphate is becoming more common practice in certain parts of the world (Brazil, Russia) where igneous phosphate ores are processed. Igneous phosphates are generally finer grained (&lt; 200µm) than some of the traditional sedimentary phosphates (&lt;400µm). Australian phosphate from the Georgina basin is sedimentary, but has a much finer grain size (typically &lt; 106µm) than similar deposits in North Africa and the USA.In 2013, Arianne Phosphate completed a bankable feasibility study for the development of their igneous phosphate deposit at the Lac a Paul site in Quebec. Initially, lab test work and bench scale piloting indicated that using traditional mechanical flotation would be able to produce adequate concentrate grade and an economic level of recovery, but would necessitate the installation of a complex and operationally challenging flotation circuit. Later pilot plant testing using column cells resulted in a significant reduction in process complexity and facilitated the processing of the -20µm ore fraction which resulted in a 10% increase in P2O5 recovery and a 5% increase in concentrate grade %P2O5.Flotation column testing achieved a concentrate grade of 38.6% P2O5 at a P2O5 recovery of 90%. Using a mechanical flotation cell circuit, the concentrate grade was 36.4% P2O5 with a P2O5 recovery of only 78.8%. A noticeable feature of the testing was the simplicity of the column flotation circuit configuration (Rougher + 2 stages of cleaning + Cleaner Scavenger) compared to the mechanical flotation cell circuit (Rougher + Scavenger + 3 stages of cleaning).The financial benefit for this case study was estimated using a sales price of US$ 195/t FOB for a 38.6% P2O5 product, and an assumed cost of production of US$ 95/t, the netback price is calculated at US$100/t. For a daily milling rate of 55,000t/d, the improved flotation performance provides additional concentrate production of 1,203t/d. Using the netback price calculated above, this calculates to additional gross profit of US$ 120,260/d.Annualised, this equals US$ 40.7 million in additional revenue for a similar or reduced CAPEX.The use of column flotation on fine grained phosphate ore types often requires fine grinding and desliming to liberate the phosphate value, such as the Australian sedimentary phosphate ores. This may enable the development of deposits previously regarded as uneconomic.This paper discusses the potential benefits available to operators, and developers of new projects, for the use of column flotation cells in their metallurgical circuits as assessed by an engineering company.CITATION:Wingate, E, Kelahan, M, David, J-S and Bartsch, L, 2015. Does it make cent$ to use flotation columns for phosphate beneficiation?, in Proceedings MetPlant 2015, pp 353–365 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By T. P. Meloy

Current coal cleaning technology uses heavy media (HM) for the recovery of coal in particles larger than 1/16 of an inch. Through the use of float sink measurements of the feed and products to commercial HM unit operations, a selection function, sometimes called Tromp curve in the coal industry, can be computed. Since the selection function is a plot f the probability of a particle appearing in the float versus the particle density, the slope of the curve will be sharper at the point where the particle has a 50% chance f appearing in the float. Thus, the separation will be better. Fine-tuning a unit operation or a circuit of unit operations requires that the selection function be accurately known. By current practice, it is difficult to obtain an accurate measure of the slope because, when the selection function is plotted versus density, the data forms an S-shaped curve which lacks data points near the 505 point of the curve. This lack of sensitivity in measuring the slope means that small recovery improvements cannot be detected; thus, only large improvements are measurable. Since most engineering improvements are small when individually considered, but large when aggregated ever many small improvements, this lack of measurement sensitivity rules out the slew march toward improved efficiency. This paper presents a method of analyzing heavy media selection functions resulting in a far more effective measure of the selective function slope. Furthermore, this improved method is applied to a number of industrial coal cleaning plants for both heavy media and heavy media cyclones. Using the work of Hudy (1968), and Deurbrouck and Hudy (1972), selection functions for individual unit operations in each plant are calculated as a function f particle size as well as density.

Jan 1, 1982

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.&apos;s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By A. Bouchard

"Based on laboratory testwork, a two-stage cleaner / re-cleaner circuit with feed regrind was proposed to replace an existing single-stage middling circuit treating a scavenger concentrate at Inco’s Clarabelle mill. In order to effectively transfer the technology and implement the new flowsheet in the plant, an extensive on-site pilot plant campaign was conducted. After demonstrating the improved metallurgy, the two-stage middlings circuit was successfully implemented at the operation.The present paper describes the on-site pilot plant testwork and the plant metallurgical improvement after implementation of the new middlings circuit. The addition of TETA / Na2S03 greatly enhanced the pentlandite selectivity against pyrrhotite and the two-stage cleaning considerably improved the pentlandite selectivity against rock minerals. The improvement was immediate after the installation of the new middlings circuit. Size by size recovery analysis indicated that a finer regrind would further improve the metallurgy of the new two-stage cleanerhe-cleaner circuit and those modifications are in progress at the mill.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill has been described elsewhere (Kerr and Kipkie, 1985; Agar, 1991). While maximizing the recoveries of chalcopyrite (Cp) and pentlandite (Pn), continuous effort has been directed toward improving pyrrhotite (Po) and rock minerals (Rk) rejection. Inco discovered diethylene triamine (DETA) and triethylene triamine (TETA) (Marticorena, et al., 1994) for pyrrhotite rejection. Falconbridge further improved pyrrhotite rejection using DETA and SO2 (Kelebek, et al., 1995). No special technologies are used in the rejection of rock minerals."

Jan 1, 2001

By B. A. Slaker, T. Miller, M. M. Murphy

An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in.) was measured by the extensometers, photogrammetric reconstructions and laser scanner over a six-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls were significantly lessened.

Jan 1, 2018

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By J Andrina, D Richar, R Smart, A Neale

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. From 2003 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A major focus of the investigations is developing strategies to maximise the beneficial use of the limestone that will be mined. Laboratory columns and field test pad investigations have been ongoing for six years examining limestone blends. Trial dumps utilising truck placement and conveyor/stacker placement and blending of limestone and acid generating rock have recently been constructed. In addition, based on initial results, investigations aimed at further evaluating the performance of limestone covers in this high rainfall environment have commenced. A significant finding has been the identification of strong armouring layers on sulfide surfaces within well-blended material and under limestone covers. These layers effectively isolate sulfides and thus progressively slow the oxidation rate to a level where the alkalinity load from the limestone exceeds the rate of acid generating. ARD is controlled and neutral low metal drainage results. The results have demonstrated that although limestone blending is effective, it is necessary to ensure that all size fractions within the blend receive adequate acid neutralising capacity to buffer the potential acidity. Because the sulfur content generally increases and the acid neutralising capacity decreases with decreasing particle size in limestone blends, the amount of limestone required greatly exceeds the stoichiometric requirement. This paper describes the development of limestone blending specifications for potentially acid forming overburden and presents the results of the ongoing limestone cover trials at the Grasberg mine.

Jan 1, 2003

By Myles E. Altimus

One responsibility of a manager is to improve his human organization. Some executives believe a manager should be measured and compensated accordingly on the basis of his ability to improve the quality of his human organization. Officials in the coal mining industry have had a tough road to travel in this regard due to fluctuating coal production demands, contractual obligations, and improved mining equipment and methods. The time may have finally arrived when we are able to recruit, select, and develop men from the labor market to fill vacancies, This is particularly true of our maintenance organizations. Because of the importance of this responsible function and the types of skills required, we must develop an extensive improvement pro- gram. Anyone in the industry who fails to undertake a manpower audit and who accepts a philosophy which will not permit collective planning, organizing and con- trolling the improvement of the human element throughout his maintenance organization may certainly cause deterioration within his company.

Jan 1, 1966

By Robb. V. M., F. Walraven, L. J. Robb

"Abstract -The old Albert Silver Mine is a polymetallic deposit comprising concentrations of Cu­ Pb-Zn-Ag-U-F within a set of sub-parallel quartz-hematite veins which occur within the fine-grained apical phase of the 2050 Ma old A-type Bushveld granites. Mineralization occurs as an early pyrite­ chalcopyrite-arsenopyrite-galena-sphalerite-(argentiferous) tetrahedrite paragenesis followed by a later, more oxidized assemblage comprising chlorite-hematite-fluorite-pitchblende. Accumulation of metals appears to have taken place at the interface between a coarse-grained porphyritic granite and an overlying fine-grained phase: veins occur in the latter and represent leakage of magmatic fluids from the differentiated, water-saturated, subjacent granite.Mineralization processes in the Bushveld granites are believed to be related to long-lived circulation of dominantly magmatic fluids stimulated by the high heat productive capacity of the host rocks. Endo- and exogranitic tin-tungsten and base metal mineralization formed during an evolving hydrothermal system that lasted for several hundred million years, forming innumerable small- to medium­ scale polymetallic deposits. At the Albert Silver Mine, unroofing of the cover sequences at circa 1600 Mato 1700 Ma resulted in the incursion of lower-temperature, high-f02 meteoric fluids which remobilized the earlier sulfides and introduced the paragenetically late U-F mineralization ."

Jan 1, 1994