Search Documents

By S. Shairp

At the Hudbay zinc pressure leach plant, filtration and washing of the second stage leach slurry takes place on a vacuum belt filter prior to disposal to tailings. Due to periods of poor filterability, laboratory studies were undertaken to investigate the effect of temperature of the filter feed slurry, and to compare filterability to the resulting cake particle size distribution.

Jan 1, 2014

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By Van E. Shaw

Three comparatively simple, efficient, and rapid extraction methods for the dissolution of yttrium and rare-earth elements from a euxenite carbonate residue have been developed, using dilute sulfuric acid as the solvent. Extraction processes have resulted in yields of 98+ percent of the total rare-earth elements and yttrium contained in the residue and have given preliminary separation between the cerium-group and the yttrium-group rare-earth elements. Extraction procedures presented are: Procedure 1. -The recovery of total rare-earth elements and yttrium by a cold dilute sulfuric acid leach at a pH of 2.5. Procedure 2. -The recovery of yttrium and yttrium-group rare-earth elements by leaching with dilute sulfuric acid at 125° F. and a pH of 3.0, with subsequent recovery of the cerium-group rare-earth elements by a cold dilute sulfuric acid leach of the residue at a pH of 2.5. Procedure 3. -The recovery of the total rare-earth elements and yttrium by fractional leaching as in procedure 1, followed by boiling the sulfate solution, which precipitates the cerium-group rare-earth elements and leaves the yttrium-group rare-earth elements in solution.

Jan 1, 1959

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By Smuts. E. M.

This paper describes a methodology used to develop a numerical model for the study of particulate suspension rheology. Initially, Computational Fluid Dynamics (CFD) models of different rheometer geometries were tested with both a Newtonian fluid (water), and a non-Newtonian Herschel-Bulkley slurry. Rheograms were reproduced from these models and compared to experimental values. Once a single-phase model had been validated, a coupled model combining CFD and the Discrete Element Method (DEM) was created. Two open source software packages were chosen. CFD is implemented using Open FOAM®, and DEM using LIGGGHTS. These two different codes were coupled via another program called CFDEM. This coupled model is currently capable of modeling spherical particles in a suspending liquid. DLVO forces have been included in some models to account for inter-particle forces due to the surface charge on the particles. The coupled model is currently being validated. Preliminary results show good qualitative behavior of the model. Keywords: rheology, cfd, dem, suspensions, modeling

Sep 1, 2012

By P J. Willems, B J. Junor

Blackwater Mine is in the central-southern Bowen Basin, immediately south of the township of Blackwater on the Capricorn Highway. The current open cut operation extracts coal from three main seams, designated Top, Middle and Lower, in the Late Permian Rangal Coal Measures cropping out on the eastern flank of the Comet Ridge. Complex geological structures, dominated by E-W normal faults and N-S reverse faults, have significant detrimental effects on coal mining operations. Historical exploration before 2010 involved several types of drilling only to understand structure, coal quality and washability. Hence, although drilling data was combined with limited pit mapping and observation, unknown structures were still often encountered during excavations and led to mining surprises. In 2010 BHP completed 200-line km of closely spaced 2D seismic survey to capture gross and detailed structures followed by fit for purpose structural drilling to confirm major structures in the northern part of the mine. In 2018 a high density 9.2 km2 3D seismic survey was completed in the southern part of the mine. Subsequently, a 17.2 km2 survey was completed in 2020 to cover the northern active mining area. It allowed geoscientists to successfully map previously unknown major faults and seam splits, which could potentially impact the mineability of the area. It is important to note, that faults interpreted using modern high-density 3D data can be interpreted with dramatically higher confidence in the fault dip and azimuth orientation in comparison to the legacy 2D data. Along with targeted drilling, pit mapping and structural interpretation, the outcome adds value to mine planning and operations. This paper outlines recent successful seismic 3D data acquisition and interpretation. In detail, the paper presents case studies on how the data can be incorporated into a structural model to improve geological knowledge, enable geotechnical assessment, and support safe and efficient coal mining in a large and structurally complex mine.

Mar 22, 2022

By Alan M. Russell

In recent years, several rare earth intermetallic compounds with the B2-type structure have been reported to exhibit high tensile ductility and high KIC fracture toughness at room temperature. These materials retain considerable ductility even at 77K. These are noteworthy findings because most intermetallics possess poor room temperature ductility and low fracture toughness unless one or more special contrivances are applied (e.g., doping with small additions of interstitial elements, offstoichiometric compositions, testing in ultra-dry atmospheres, etc.). This paper summarizes recent findings on rare earth B2 intermetallics. These include the determination of the active slip systems; the strain rate sensitivities; yield strength maxima at elevated temperatures; the search for possible twinning and stress-induced phase transformations; ab initio calculations of their defect energies and the anisotropy of dislocation line tension. Potential applications of these materials and the possibilities that this study may suggest strategies for increasing ductility in other intermetallic compounds are discussed.

Jan 1, 2008

By Renpei Yoda

An investigation was conducted to develop columbium alloys with e1evated-temperature strengths higher than those exhibited by more common commercial columbium alloys, and attention was given to improving the oxidation resistance and ease of fabrication. Additions of carbon, aluminum, and chromium were made to some columbium-base alloys, and their effects on workability, recrystallization, oxidation resistance, and mechanical properties at elevated temperatures were explored. The additions were made to take advantage of (1) solid solution strengthening, and (2) precipitation hardening. Three alloys displayed good high-temperature properties with relatively good oxidation resistance at 1,000° C, and tensile strengths from 26,000 to 32,200 psi at 1,400° C. When the properties of these alloys were compared with those of commercial alloys, B-66 and FS-85 (1),4 the outcome was favor-able for the alloys studied in this investigation.

Jan 1, 1967

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology to support Industry 4.0 has become the target of academic research in many sectors. This study reviews the trends of open-source technology, its forms, and some industrial applications. As a case study of the use of open-source hardware and software in the mining industry, this study proposed a low-cost environmental monitoring system for nonmetallic underground mines to support mine safety and occupational health. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device, and open-source software, MIT App Inventor, to develop an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a nonmetallic underground mining site to assess the performance of the system in mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors.

By Baokuan Li, Fang Wang, Meilong Shan

"As the advantage of uniform bus loading, the electroslag remelting (ESR) furnaces with three - phase installation by delta or star connection are mainly used to produce the large or super large ingot. The electrical efficiency is significantly improved as the short circuiting through the molten slag. However, little is found about fiindamental research on the electromagnetic field of the ESR system with three -phase installation. A three-dimensional (3D) finite element model was developed to simulate the current density, magnetic field, electromagnetic force and Joule heating for a system of electrode, slag and ingot in the ESR system with three -phase installation.IntroductionThe metallurgical performance of the ingot is the fundament and precondition to obtain the large forging of high quality, which has a critical role in the producing of forging. The electroslag process (ESR) to product the metal materials of high homogenization and clarity become more and more popular[1].The electroslag process is a special smelting technology of producing small ingots, which originate in 1950[2].At present the three, four or six electrode is used in large scale electroslag furnace. It has been found that the deeper molten pool and the wider of the two-phase zone with only one large diameter of electrode to product large ingot effect the solidification microstructure of ingot[3]. However, the molten pool becomes shallow relatively with several electrodes producing the large ingot, which is benefit to the solidification microstructure of ingot. Three electrodes electroslag remelting furnace take the three phase equilibrium power supply to making the load and electric power network balance, avoiding the distortion phenomenon induced by single phase power supply and saving electric power. It also can uniformize the distribution of heat source."

Jan 1, 2012

By G. Kleyn

"Sub-standard practices and their adverse impact on safety performance remain a challenge in the South African gold mining industry. The purpose of this study was to investigate the root causes of sub-standard practices and the effect on safety performance in South African gold mines. The focus of the study was on the underground production operations at a gold mine in the Free State. The study consisted of three parts: a personal investigation into the causes of sub-standard practices at the mine, a comparison with the results of a cultural study performed at the West Wits mines, and a behavioural survey.The studies described in this article yielded similar results in terms of the key drivers behind sub-standard practices. It was found that substandard practices had a number of causes, and the origin lies within the habits, attitude, and behaviour of employees. Current methods of addressing sub-standard practices and improving safety performance were found to discourage employees from performing work safely and according to procedure. It was concluded that the lack of critical behavioural habits for the given work environment and job title could possibly be the primary reason for the occurrence of sub-standard practices. IntroductionSince the implementation of the Mine Health and Safety Act, 1996 (Act 29 of 1996) and the Mine Health and Safety Regulations, the South African mining industry has been striving to improve health and safety performance and has placed great emphasis on adherence to mine standards.The Act requires employers in the mining industry to report accidents, incidents, and dangerous situations to the Regional Principal Inspector of Mines in their area. The data provided by employers is captured and analysed by the South African Mines Reportable Accident Statistical System (SAMRASS) and made available for public viewing (Department of Mineral Resources, 2011).A review of the national mine-related accident statistics shows clearly that the South African gold mining industry has improved its safety performance markedly over the past decade, but is still facing major challenges (Figure 1). These include meeting the Mine Health and Safety Milestones (Department of Mineral Resources, 2011)."

Jan 1, 2016

By J. J. Luchessa

HAULAGE was one of the many problems to be solved in the successful handling of the Miami Copper Company's low-grade orebody. The ore extracted had to be increased from 1000 to 18,000 tons per 24 hours over the existing track-age and haulage way. This called for increased speed, longer trains, in¬creased car capacity, and a block signal system so as to maintain a fixed schedule and headway. The motive power in service at the time of this transition consisted of Baldwin-Westinghouse 6-ton trolley locomotives. (See Fig. 3.) These locomotives were purchased to handle twenty inverted-V-bottom side-dump cars of 60 cu. ft. capacity. Dimensions were limited as to height on account of ore chutes, width on account of short radius curves, and length of 12 ft. from bumper to bumper- so that the locomotives could be handled on the man and material hoist which has a cage length of 121/ ft. The limited length made it possible to bring the locomotives to the surface for periodic overhauling and major repairs such as changing wheel tires, gears, and

Jan 1, 1934

By Brian McInnes, Joseph A. Sopko, Behzad Khorshidi

"The Port Mann Main Water Supply Tunnel involves a 1km long tunnel beneath the Fraser River from Surrey to Coquitlam, BC. At depths of up to 60 m below ground, the earth pressure reached 6 bar. The tunnel is constructed using an EPB TBM and gasketed precast concrete segmental liner. The tunnel and two shafts were constructed in a variety of soil conditions ranging from soft to stiff clays and silts, to compact to very dense sands and gravels. After approximately 800m of mining, a very dense and highly variable soil group consisting of cobbles and boulders halted the TBM. Several options were considered to stabilize the TBM face so an intervention could be conducted. Although de-watering was considered, there was risk of settlement to the Port Mann bridge piers, which was within 500m of the tunnel. Hyperbarics were also considered, however, the cost, schedule and uncertainty of the work that needed to be done, made it a risky option. Ground freezing by Liquid Nitrogen was chosen as the best solution, which would provide a frozen block around the face of the TBM. A temporary platform on the river was designed and constructed to enable drilling and installation of the freezing pipes and temperature monitoring equipment. The operation required close coordination among the tunnelling, marine and freezing sectors. Following the intervention, the TBM successfully broke through the reception shaft, and the remaining project was completed. This paper describes the design, construction and operational approaches used for the freezing and serves as a basis for future projects requiring expedited ground freezing."

Jan 1, 2016

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alterative: the fully optimized use of the facility's present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements In the mine or plant necessary to support new technology will be equally effective when implemented for the facility's present operators. Firms who optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 1999

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By Saulo Rossini Meira

A complexidade e o elevado tempo de manutenção para a troca do rolamento da grelha móvel do forno da usina de pelotização IV, localizada no Complexo de Tubarão em Vitória - Espírito Santo, viabilizou estudar, desenvolver e implementar, via PDCA, uma solução tecnológica que reduziu riscos de acidentes, tempo de manutenção, desgaste físico e mental, como também eliminou a utilização de equipamentos móveis e o risco de quebra de componentes periféricos. Conclui-se que com a modificação implementada, foram viabilizados procedimentos de manutenção mais seguros, redução de custos e aumento da disponibilidade do equipamento para o processo produtivo.

Aug 1, 2018

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007