Search Documents

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By Abdelmalek Bouazza, Aamir Mahawish, Will P. Gates

Bio-grouting by means of microbial induced calcite (calcium carbonate) precipitation (MICP) to improve mechanical properties of granular soils has gained much attention in recent years. The biogrouting process offers an alternative and environmentally friendly approach to conventional soil improvement techniques, such as cement. Bio-grouting by urea hydrolysis has been extensively applied to tackle various geotechnical problems. However, it has yet to be applied to improve engineering properties (compressive strength) of a coarse cohesionless material with the aim using it as sand/stone columns within soft and very soft soils. This paper investigates the effect of using light, moderate and heavy biochemical treatments on the unconfined compressive strength (UCS) of coarse sand columns. In addition, the microstructure of the bio-cemented coarse material has been analysed by X-ray computed tomography (XRCT). The experimental results revealed that the UCS could reach up to 200kPa, 1000kPa and 5500kPa for light, moderate and heavy bio-cemented coarse sand columns, respectively. The microstructure investigations showed that the deposited calcium carbonate can be identified using XRCT imaging and can be associated with the gain in UCS values. Various microstructure properties, such as void ratio, dry density and porosity were also identified and compared with the laboratory data.

Jan 1, 1900

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By Edward Martinez

Due to its unique properties, chrysotile asbestos is used in many diversified applications. In recent years, a better understanding of the structure and properties of chrysotile has evolved due to the research efforts of many investigators. A summary of the results of some of these investigations is given. An attempt is made to show the relationships between the properties of chrysotile and its crystal structure. Examples taken from the literature are cited in which methods have been developed for modifying the properties to improve the performance of asbestos in some applications. These include the effect of pH on the positive zeta potential and the addition of sodium silicate to improve filtration characteristics. The dehydroxylation and formation of forsterite when chrysotile is heated are also discussed.

Jan 1, 1966

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By Brad Grothen

What is the most economical way of tunneling in mixed ground that may experience high pressures? Non-continuously pressurized, mixed ground Tunnel Boring Machines (TBMs) are being utilized to deal with a wide range of geology. Continuous improvements in these mixed ground machines allow for ever-increasing efficiency and reduction of project risk due to unexpected conditions. We will explore the performance of recent mixed ground machines throughout the world and then look at how new improvements to mixed ground machines will enable excavation of an expanded range of ground conditions. These conditions include mixed ground with low fines, mixed face rock, and fracture/fault zones with high pressures where in the past a Slurry TBM may have been utilized.

Dec 1, 2022

By L. E. Young

THE progress of mineral industry education will be limited to the period prior to World War II and will be considered as primarily a division of engineering education. Its relation to progress in the mineral industry and to the activities of the American Institute of Mining and Metallurgical Engineers will be emphasized. The history of mineral industry education has been recorded most completely and authoritatively by Dr. T. T. Read in his recent volume in the Seeley W. Mudd Series of American Institute of Mining and Metallurgical Engineers publications, entitled, The Development of Mineral Industry Education in the United States. Therefore, most of the historical details will be omitted from the discussion and an effort will be made to point out significant developments and to analyze trends. INTRODUCTORY STATEMENT AND SIGNIFICANT POINTS IN PROGRESS Among the significant points in the development of mineral industry education in the United States since 1871, the following deserve particular mention: I. The number of institutions offering undergraduate instruction has increased, particularly during the years 1890 to 1925; the number of students enrolled in undergraduate study has increased greatly, largely on account of the development of courses in petroleum engineering and increasing interest in metallurgy. 2. The selection of students to be admitted to undergraduate courses has been improved through the advisement, counseling, and guidance programs sponsored by the Engineers' Council for Professional Development. 3. Improved instruction methods and the training of the teaching staff have been promoted by the educational institutions themselves, but with the most effective stimulus and guidance of the American Society for Engineering Education and the Engineers' Council for Professional Development. 4. The accrediting of undergraduate curricula through the Engineers' Council for Professional Development, considering both qualitative and quantitative criteria, has done much to improve standards of instruction in engineering education for the mineral industry. 5. Undergraduate curricula and courses are revised currently to meet the needs of the American mineral industry. New curricula are developed currently to permit specialization in technical fields, particularly in the fourth year of undergraduate work. 6. There has been a strengthening of the fundamental courses in mathematics, physics, mechanics, and chemistry, and at the same time these courses are being adapted to the most recent developments in the industry, including metallurgy, geophysics, petroleum engineering, petroleum technology, ceramics and so forth. 7. There has been continuing improvement in plant and laboratory facilities of the educational institutions.

Jan 1, 1947

By L. E. Young

The progress of mineral industry education will be limited to the period prior to World War II and will be considered as primarily a division of engineering education. Its relation to progress in the mineral industry and to the activities of the American Institute of Mining and Metallurgical Engineers will be emphasized. The history of mineral industry education has been recorded most completely and authoritatively by Dr. T. T. Read in his recent volume in the Seeley W. Mudd Series of American Institute of Mining and Metallurgical Engineers publications, entitled, The Development of Mineral Industry Education in the United States. Therefore, most of the historical details will be omitted from the discussion and an effort will be made to point out significant developments and to analyze trends. Introductory Statement and Significant Points in Progress Among the significant points in the development of mineral industry education in the United States since 1871, the following deserve particular mention: 1. The number of institutions offering undergraduate instruction has increased, particularly during the years 1890 to 1925; the number of students enrolled in undergraduate study has increased greatly, largely on account of the development of courses in petroleum engineering and increasing interest in metallurgy. 2. The selection of students to be admitted to undergraduate courses has been improved through the advisement, counseling, and guidance programs sponsored by the Engineers' Council for Professional Development. 3. Improved instruction methods all the training of the teaching staff have been promoted by the educational institutions themselves, but with the most effective stimulus and guidance of the American Society for Engineering Education and the Engineers' Council for Professional Development. 4. The accrediting of undergraduate curricula through the Engineers' Council for Professional Development, consitlering both qualitative and quantitative criteria, has done much to improve standards of instruction in engineering education for thc mineral industry. 5. Undergraduate curricula and courses are revised currently to meet the needs of the American mineral industry. New curricula are developed currently to permit specialization in technical fields, particularly in the fourth year of undergraduate work. 6. There has been a strengthening of the fundamental courses in mathematics, physics, mechanics, and chemistry, and at the same time these courses are being adapted to the most recent developments in the industry, including metallurgy, geophysics. petroleum engineering, petroleum technology, ceramics and SO forth. 7' There has been continuing improvement in plant and laboratory facilities of the educational institutions.

Jan 1, 1949

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

Tracey Khanna, Assistant Editor of UK?s Mining Magazine discusses some of the new and important environmental challenges, physical and social, that are facing mining companies. The tide of public opinion has turned strongly against those companies which are unable to show that they are practising responsible environmental stewardship. This is, no doubt, in part due to the recent focus of the international media on environmental issues and constantly improving means of communications, which has brought the whole subject of mining and the environment to those who, in the past, had only a limited awareness of the industry. Mining companies today face new and important challenges with regard to the environment, both physical and social. New technology and a greater understanding of waste management techniques has helped to bring about improved handling and disposal of mines wastes, so reducing some of the impacts. However, improved technology has also brought about the economic viability of exploiting increasingly lower-grade ore from open pits, resulting in a greater visual impact.

Jan 1, 2000

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By Timothy D. Dreger

In the spring of 2009, Suncor Energy Inc. technical personnel saw an opportunity to improve planning 0and mining of overburden material in order to address aggressive construction goals and increased mining complexity. By tying together current and historical equipment performance, geological model information, and material observation in the field new operating elevations for the shovels were developed. At the same time, methodology of recording and reporting overburden movement through the Modular Mining DISPATCH system was changed. The result of this first stage of improvements was an increase in construction-grade material available at the face. The personnel involved realized that other opportunities were available to build on the initial successes and establish processes that would stand up to attrition and experience levels. A cross-functional technical team was assembled to identify ways of further improving workflows around overburden mining. Some of the opportunities realized include greater alignment between planning, reporting and operations as well as development of reporting tools that help steward Mine Operations to the plan. All of which have resulted in Suncor meeting or beating its forecast overburden targets. The cross-functional technical team continues to seek out new and better ways of doing business so Suncor can continue to deliver on its commitment of outstanding performance and results.

May 1, 2011

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

The Australasian Institute of Mining and Metallurgy brings together, voluntarily, people with a professional interest in the disciplines and skills which are employed in the mineral indus- try, and in relation to that industry. We come together because we have a mutual interest in improv- ing what is done by the mineral industry, in all its aspects. It is this sense of continuing improvement, of doing better, of doing as well as we can, as our knowledge and skills improve, that unites us in creating and fostering a professional association of like- minded people. We know from our professional training and experience that enormous progress has been made, at an ever-increasing rate, in the mineral industry, particularly in this Century. We know that the mineral industry has played a very major role in providing the means by which so many more people survive to live longer, healthier and more interesting lives, than ever before. Indeed together with the oil and gas industry, which is an integral part of the mineral industry but has achieved its own commercial dis- tinction, it is fair to claim that the mineral industry has played the major role in providing the means for the advancement of the human quality of life.

Jan 1, 1988

By J. R. Finlay

THE other day, I fell into conversation with two gentlemen who desired to improve the condition of the people; so that the talk was semi-political. They seemed to agree that I was inclined to be "con-servative," "reactionary," perhaps an "evolutionist," looking upon "reform" with suspicion. Finally I rejoined somewhat in this manner: "You attach to me phrases that I have heard all my life but which convey no meaning to me. It is quite true that I do not make a fetish of terms like reform, liberty, democracy and so forth; neither do I worship the idea that `things are good enough as they are,' `leave well enough. alone' and so forth. There is more satisfaction in building something up than in tearing something down, or in just maintaining something that is already built. Progress is a popular word; but what is progress? In my opinion it is comprised, so far as public welfare is concerned, of two elements: Improvements in production of goods and knowledge; improvements in keeping order." This substitute for politics, economics, reform, pro-gress, conservatism, radicalism, democracy, socialism, monarchism and all the phrases of public welfare may seem over-simple; perhaps it is, but at least it defines something. It seems to me to be at least worth attention.

Jan 4, 1922