Search Documents

By O. R. Wagner, R. O. Leach

Immiscible displacement tests were performed in a consolidated sandstone core over the interfacial tension range from less thdn 0.01 to 5 dynes/cm to better define how interfacial tension (IFTJ reduction can lead to increased oil recovery. Data obtained were displacement efficiency at breakthbrough vs IFT for both drainage and imbibition conditions. These tests simulate water flooding under oil-wet and water-wet conditions, respectively. Results of the study have shown that displacement efficiency under both oil-wet and water-wet conditions can be markedly improved by a sufficient reduction in IFT. In the particular porous media used and for the low pressure gradients employed, the IFT must be reduced to a value less than about 0.07 dynes/cm to achieve increased recovery at the time of breakthrough of the injected phase. Below 0.07 dynes /cm, further small reductions in IFT result in large increases in displacement efficiency. Observed increases in recovery were obtained at pressure gradients which are well below those which can exist in the interwell area of a reservoir under water flood. The effect of pressure gradient on recovery is discussed. INTRODUCTION A residual oil saturation remains in rock which has been water flooded because, under usual reservoir conditions, the driving force which can be generated is inadequate to expel oil trapped by capillary forces. Since these capillary forces can be reduced by reducing the IFT a frequently studied method of increasing oil recovery has been the use of surfactants to reduce the water-oil interfacial tension. Mungan l observed improved recovery in both water-wet and oil-wet systems at 1.1 dyne /cm IFT, finding that the amount of improvement was greater in oil-wet systems. Moore and Blum,2 working with visual flow cell micro-models, con- cluded that recovery cannot be improved in water-wet systems by injecting surfactant solutions. They calculated that, for a pressure gadient of 1 psi/ft in their model, the IFT must be reduced to 0.03 dynes/cm to release oil trapped under water-wet conditions. Berkeley et al.3 indicated that, at representative field flooding rates, the IFT must be reduced to 0.001 dyne/cm to improve recovery, Thus, there is a wide variation of opinion about the IFT levels needed to improve recovery under field conditions. These previous investigators all have used as their experimental method the addition of surfactants to the injected water. The use of surfactant solutions to reduce IFT creates two experimental problems: (1) the loss of surfactant through adsorption on reservoir rock can obscure the true IFT value which exists at the displacement front, and (2) at very low values of IFT emulsifica-tion of oil and water commonly occurs. It is difficult, therefore, to determine whether the increased recovery is caused by IFT reduction as such, or is instead caused by emulsification. Also the properties of the available surfactants limit the IFT range which can be studied. In the present study the purpose is to better define how interfacial tension reduction can lead to increased oil recovery. A matter of great interest is the amount of recovery improvement potentially achievable in this way. The study was made using very low pressure gradients which was well within the range achievable by water flooding in the interwell region of petroleum reservoirs. A unique experimental approach was chosen to avoid adsorption and emulsification problems, and to allow convenient control of IFT. The fluid phases used were the equilibrium vapor and liquid phases of the methane-n-pentane system. The interfacial tension level was varied by changing the equilibrium pressure of the methane-pentane system over the range from 1,200 psia to near the critical pressure (2,420 psia). All tests were performed at a controlled temperature of 100F. The IFT-vs-pressure relationship for the methane-pentane system was based on the data of Stegemeier and Hough,6 and on new data obtained in this study. With this experimental approach it has been possible to study displacement at lower values of IFT than have been previously investigated.

Jan 1, 1967

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By Jinrong (Patrick) Mang

Three of the most challenging problems in phosphate beneficiation are discussed: flotation efficiency, resource conservation and environmental impact. Some new flotation machines offer the opportunity of reducing power and reagent consumption significantly, while increasing specific capacity many fold. Efficiency might also be improved dramatically by replacing the "double float" process with a single-collector scheme. Model based software control is a powerful tool for improving overall plant efficiency. Recovery of phosphate values from the phosphatic clays could extend phosphorus reserve life significantly. phosphate recovery from the slimes might be achieved by sizing-flotation, selective flocculation and bioleaching. Reducing the volume of phosphatic clays produced is another key stop to minimizing phoephate logs. Such a reduction may be realized by floating at finer cut size. Although an ideal' dolomite separation process is yet to be developed, a cationic flotation process may prove to 'be economically feasible. Loss of phosphate in the desliming stage is the major problem with most of the flotation schemes for removing dolomite.

Jan 1, 1995

By J J. Cilliers, K Hadler

The potential of air rate profiling to significantly improve the flotation performance of a bank of cells has been shown by numerous studies. To date many profiles have been evaluated; balanced, increasing, decreasing and combinations of these. An increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, has been typically found to yield improved flotation performance compared to other profiles. Air rate profiling has two distinct components; determining the correct total air rate for the bank, and determining the correct distribution of that air. This can be done simultaneously by finding the optimal air rate to each cell in the bank in turn through air recovery optimisation. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement of optimal performance for the operating conditions in the cell, and sets the PAR air rate. In this study, plant trials of different air rate profiles and profiling based on PAR, were evaluated. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The highest cumulative mineral recovery was achieved by operating at the PAR air rates for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this work the upgrade ratio is defined as the ratio of the concentrate grade to the feed grade. The increase in cumulative mineral recovery, at the same upgrade ratio, in this study was greater than 33 per cent. Air recovery based optimisation of air rates to banks of cells significantly improves flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By Clarence E. Killebrew

The key to the successful use of any tool, more than anything else, depends upon proper application assignment. To achieve this, the individual having such machine responsibility must maintain fresh knowledge of technical improvements that broaden machine uses. 8.3-1. Tractor Shovel. This type machine is available in a wide range of sizes mounted either on crawler tracks or rubber-tired wheels, with both two-wheel and four-wheel drive. The original concept in both crawler and rubber mounting was that of an attachment to be added to a tractor already in existence. This served as an important expedient for the introduction of the tool, but the basic tractor proved to be inadequately designed for the additional loads. In spite of these structural inadequencies, customer acceptance generated sufficient revenue that further development could be financed for product improvement. The evolution of the product is continuing in many ways-including engines, drive line components, tires, hydraulic pumps, hydraulic valves, structural steel, etc. With each improvement, the operating capability of the machine is extended. This is resulting in the rubber-tired, four-wheel-drive concept making an invasion of the job applications that were formerly considered suitable only for crawler-track mounted machines. Both rubber- and crawler-mounted tractor shovels have invaded the market of small excavator shovels. Larger tractor shovels are challenging the larger size excavators. It is important that each job application be carefully considered so that the proper machine is put in operation. The performance varies widely in operating cost, production efficiency, and job flexibility. Factors to be considered in equipment selection are: 1. Nature of material to be moved 3. Distance material must be moved 2. Surface over which material must be moved 4. Quantity to be moved 5. Secondary or alternate use capability

Jan 1, 1968

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

By André de Cabral Oliveira

With the onset of the global economic crisis in 2008, and more precisely from 2009, production routes in iron making as blast furnace, sinter and coke oven, indicated a significant increase in frequency as well as intensity of undesirable incidents. The cost impact of such deteriorations of the production chain cause significant losses ranging up to several hundred million dollars annually. On the other hand, opportunities for processes improvement are contributing to enhance process efficiency and results, and also reduce or even avoid losses from unexpected incidents. The use of specialized services for processes has gained projection along the plants and emerged as an attractive alternative to increase results by increasing the performance and reducing costs and expenses. Process Services are formatted to achieve cooperative and customized solution during planned or urgent interventions, conducting feasibility studies, process improvement, training, among others, providing knowledge, information and crucial actions to preserve and optimize processes and plant facilities.

Aug 2, 2018

By J. Duncan Wilkins

Introduction In difficult times such as these, there is a strong reaction to the current way of doing things. Typical reactions that we have all heard are "There has to be a better way," "We're pricing ourselves out of business," "We have to improve our productivity," and "We have to have more cooperation," between union and management and employees and management. All of these comments have at their roots one common factor - getting the maximum amount for your dollar. The other factor inherent in these statements is productivity. I have not yet met a person in our industry who has not expressed the opinion that we should, and that we can, improve our productivity. Reducing Labor Costs In light of these factors I suspect we have all spent a fair amount of time examining our labor costs. For some of us, labor costs are a high proportion of our total cost of doing business. To alleviate the impact of these costs, we have generally done four things. We have reduced our number of employees, shut down operations for appropriate periods, sought concessions from union employees, and placed freezes on wages, salaries, and other benefits on nonunion employees. These approaches have been made to improve current shortfalls in our cash positions - to tide us over, as it were - or to provide us with a chance for survival. These are short-term measures that help to bring immediate relief, but can pose significant problems (or challenges), for the longer term. For instance, what do we do when times improve? How much do things have to improve before we do anything? By seeking concessions from unions in bad times, what do we do when unions come to us in good times? It is a rather sad and critical fact that we have grown too fat during the good times and too thin during the bad. In the first case, we have failed to optimize our earnings. In the second, we have cut ourselves too far. Consequently, when good or better times have arrived, we have had to bulk up our requirements to meet production commitments. In mining, for example, when times become tough, we tend to reduce our development plans so that when times improve we have to really "sock it to 'em," so that we can maintain productive capacities. We should plan ahead a little more to reduce the amplitude of our cyclical wavelength, so that in good times profits are optimized and in bad time we are better able to take the strain. Of course, forecasting cycles is not a refined art, but if we properly control our work force levels and costs at all times, and therefore optimize our productivity, we would be more able to withstand the problems we face today. Unfortunately, it appears that it takes bad times to bring us to a realistic appraisal of our way of managing our businesses. Labor Practices Not all of the problems now faced are due to low metal prices. Inflation has played a major role in bringing costs to a frightening level. Trade unions alone can not be blamed for high inflation levels over the past several years, popular though that notion is. Contract negotiations, after all, require two parties. Indeed, our current levels of labor cost are due to two factors: • We have felt obliged to keep our employees whole, relative to the cost of living. • We have felt obliged to maintain our competitive position relative to our peers, in order to maintain our ability to attract and retain a skilled, efficient work force. In the first case, our felt obligation has been applied without due recognition of the factor of performance, either in individuals or groups. Average, even mediocre performers, have been amply rewarded for their average work and mediocrity, while the good performers, no doubt receiving more for their good work and effort, have not perhaps appreciated the slight premium for their effectiveness. The rather predictable result of this practice has been that the average and mediocre stay that way (why change?), while some (certainly not all) of the good performers have said "It's not worth it," and slipped into the warm, cosy pool of the average and mediocre. In the second case, that of maintaining competitiveness with other companies' employees, we have compounded an already serious problem of lack of skilled tradesmen by paying higher and higher prices for the existing pool to maintain comparability without improving the flow of more skilled people through sound and sufficient training programs. We have the rather dubious pleasure of paying more and more for the same problems. Compensation is either mutually agreed, as with unions, or it is unilaterally applied, as with nonunion employees. Generally, there is more flexibility available to the employer when dealing with nonunionized groups than there is with unionized groups. Sometimes that flexibility has not been used well, most often be-

Jan 11, 1983

By J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

"Ni-based superalloys have been replaced in the last low pressure stage of jet turbines for aircraft by titanium aluminides. In order to improve the properties of these Ti-Al alloys and extend their usage deeper into aircraft engines grain refinement by inoculation has been investigated. Borides are the most common inoculants for Ti-Al alloys, however they form brittle particles which are detrimental to the final properties of the alloy. Inoculants manufactured from a Ti-Al alloy with refractory metal additions were proposed to alleviate the issues arising from inoculation with brittle particles. An alloy was chosen which had less than 10% lattice mismatch with the alloy of interest (Ti-46Al) to maximize efficiency. Initial experimentation showed a decrease in as-cast grain size by a factor of 2 between the inoculated and non-inoculated samples along with an absence of the brittle particles found with boron inoculations. Investigations into the interaction between the inoculants and the melt were also carried out to better understand the inoculant size distribution and efficiency upon solidification.INTRODUCTIONTitanium aluminum alloys are an interesting material for aerospace applications. Their high temperature oxidation resistance and high specific strength make them particularly promising (Kim & Dimiduk, 1991). Recently, titanium aluminides have replaced nickel based superalloys in the last low pressure stage of the GEnx turbine engine. In order to increase their usefulness in turbines their properties must be improved for high temperature (>800oC) applications. Grain refinement is one method to improve the properties of a material, however current methods of grain refinement of Ti-Al alloys by inoculation have significant drawbacks. A new method of inoculating Ti-Al alloys by using Ti-Al alloys with small refractory metal additions (Nb, Ta) has been developed to avoid the drawbacks of current methods while still being effective grain refiners."

Jan 1, 2016

By Eduardo Rojas, Pedro Landeros

El Teniente Mine expansion plans are currently under development and construction stages through an integrated project strategy that will allow the continuity of future mining. The deepest sector corresponds to Andes Norte Project that faced rockburst risks during tunneling in a completely different manner, implementing different actions for the mitigation of seismic hazard and seismic risk management, based on the following main aspects: rock mass preconditioning techniques such as destress blasting and hydraulic fracturing, improvement of rock support design with the inclusion of elements with higher energy dissipation capacities, use of mechanized equipment for the most critical activities in addition to re-entry protocols and improvements in geological, geomechanical and seismic data collection procedures to reduce the uncertainty of rock mass behavior. The current seismic risk management strategy integrates all of these elements and is the basis of construction methodologies in use, supporting the technical feasibility of tunneling in high-stress environments.

Apr 26, 2022

By G. A. Davidson, P. G. Williams

"New developments in centrifugal slurry pump technology are discussed in relation to their importance for improving pump operation and reliability.Experimental data obtained by measuring the velocity of liquid flows in a slurry pump casing using Laser Doppler Velocimetry are presented. This demonstrates the importance of selecting pumps with the proper hydraulic design to provide optimum efficiency, maximum part life and minimum operating cost.The paper also discusses the use of new wear resistant materials, such as ceramic/metal composites, which can significantly improve the life of parts exposed to abrasive media. The results of laboratory attrition tests are presented. IntroductionCentrifugal slurry pumps are of primary importance for the hydro transport of abrasive and corrosive media in the mineral processing industry. As for all process equipment, slurry pumps must be carefully selected and operated to provide optimal performance. To achieve this, it is necessary to select equipment which will provide efficient and reliable operation for the specific service conditions and incorporates the best materials available to obtain maximum parts life.Abrasive wear of liquid end components is the most important aspect that distinguishes the design and application of slurry pumps from other types of pumps. It is therefore necessary to have a fundamental understanding of the mechanical interaction between pump components and the media being handled, as this will impact significantly on hydraulic design, mechanical reliability and selection of wear resistant materials. Recent advances in computational approaches'» have greatly improved the prediction of wear rates in pump casings by facilitating the solution of complex equations which describe the wear mechanisms mathematically. In conjunction with this, new experimental techniques allow researchers to measure flow fields in pump casings using non-invasive devices such as Laser Doppler velocimeters."

Jan 1, 1992

By D. Janney

Kennecott's Utah Smelter commenced operations in June 1995 utilizing Outokumpu Flash Smelting (FSF) and Kennecott-Outokumpu Flash Converting (FCF) technology. After some initial teething and equipment problems the smelter achieved its design capacity in mid-1997 and now processes over 1.0 million tonnes of copper concentrate per year with exceptional environmental performance. The smelting furnace has operated for 11 years and the converting furnace for 5 years without major shutdowns. The first major smelter shutdown commenced in September 2006 after extensive planning. The FSF was completely re-bricked and the latest above and below bath containment systems installed. The FCF was inspected and re-bricked with some improvements made to the above bath containment system. The FCF life is now anticipated to be the same as the FSF. Numerous improvements and modifications were made to the rest of smelter facility including extensive upgrades to the dry electrostatic precipitators. Production ramp-up was smooth with the smelter now frequently operating at acid plant capacity.

Jan 1, 2007

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By C McHugh, F Oppolzer, B Rogers, A Stokes

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation has more to do with improving the accuracy and consistency of mining processes and less to do with cost savings through labour reduction.A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation, ore loss and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio TintoÆs surface mines.This paper describes Rio TintoÆs multi-drill automation project, which has developed a robust system for automating most of the functions on several Caterpillar SKSS16 drill rigs. Automated drilling is currently being trialled in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the automated multi-drill system is given together with an overview of how automated drilling is performed remotely from the operating bench.A review of the performance and benefits of the automated multi-drill system is given together with future plans to extend the functionality of automated drills.CITATION:McHugh, C, Stokes, A, Oppolzer, F and Rogers, B, 2012. Automated multi-drills in Rio Tinto, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 83-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Paul E. Rosten

This paper describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Company to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Company operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and Western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes .each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously. (1) (2)(3) Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and furnished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate-kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1977

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By R. Jacob Cefalo, Miguel Valenzuela

The modern drill and blast engineer operates in an environment often rich with data from drilling data and blast designs vs. actuals to fragmentation distributions and vibration records. Despite this abundance, much of the information generated remains underutilized, often collected as a matter of routine rather than for a means to an end. This paper explores how artificial intelligence (AI) can bridge that gap, transforming raw operational information into actionable insights that lead to more consistent and optimized blasting outcomes. Through AI-driven analysis of drilling logs, burden and spacing measurements in design vs. actual, fragmentation distributions, and vibration records, we can identify hidden patterns and correlations that traditional analytics overlook or that we may not be aware of. These insights enable engineers to proactively adjust designs and loading strategies, ultimately improving performance aspects such as improving fragmentation, minimizing ground vibration, and lowering overall operational costs. The paper examines the industry's reliance on lagging indicators, such as post-blast fragmentation surveys or actual powder factors, and suggests the need to shift toward leading indicators like real-time drill data monitoring and predictive fragmentation modeling. Utilizing AI to forecast outcomes before a blast is carried out allows engineers to take corrective actions early in the process, thereby creating a feedback loop that continuously improves performance. This integration of AI into drilling and blasting practices marks a pivotal opportunity for the explosives engineering field to evolve from reactive to predictive methodologies unlocking a new level of operational intelligence and value creation.

Jan 26, 2026

By Paul E. Rosten

Introduction This papers describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Co. to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Co. operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously (Lindroos and Koski, 1966; Villar and Dawe, 1975; Koski, 1977). Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and fur¬nished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate¬kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to: (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1981