Search Documents

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972

In late 1987 it was recognised that column flotation might have potential for improving the grade of the zinc concentrate produced at Pasminco's South Mine in Broken Hill. Intermittent test work was carried out during 1988 using a 90 mm diameter by 6 m high perspex column, built and initially operated by staff from CRA Advanced Technical Development. This column was found to have insufficient retention time so, during the first half of 1989, Pasminco constructed and installed a 200 mm diameter unit of the same height. Extensive testwork was carried out using this column during the latter half of 1989 and early 1990. It was clear from the results that a grade improvement of between 1 and 2 per cent (absolute) would be achievable. The effect of column cleaning on overall recovery was not established with the same degree of confidence, so the proposed new circuit is to include one of the existing banks of OK8 cleaner cells as a scavenger on column tailings. The test work provided sufficient data for preliminary design work to begin in May 1990 and commissioning of full scale zinc cleaner columns is planned for mid 1991. This paper summarizes the results and describes some of the experiences with column flotation at the Pasminco South Mine.

Jan 1, 1991

The development of the Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves is a significan step towards informing the financial community and the public about the future profitability and risks of investing in resource companies. The Code is also important from the accountants' point of view because it provides them with a well-defined bash for assigning costs or attributing value to the assets of resource companies and hence improving their financial reports. Although reporting to the public is ultimately the responsibility of management, accountants, like geologists, are frequently required to provide information for inclusion in these reports. Jr the last ten years, there has been a considerable refinement in the reporting of mineral resources which can be attributed mainly tc the progress made towards developing the Code. It seems tha the classification and terminology that the geologists have developed are widely used in the annual reports. However, little progress has been made by accountants in improving the financia information. The purpose of this paper is twofold: (a) to outline briefl) some of the major problems in accounting and reporting fo; mining companies and; (b) to examine the potential contribution of the Code in solving those problems.

Jan 1, 1990

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991

By King RP, Kientzler P

In recent years, ultrasonic comminution technology has been developed at the Utah Comminution Center. An ultrasonic grinding device was assembled and investigated. An ultrasonic transducer system has been significantly improved by using a special type of piezoelectric ceramic and preloading to 4.1 x le kPa to obtain maximum strength. The improved system provides constant and rapid vibratory promotion of fatigue fracture resulting in more effective breakage. The design principles for an ultrasonic mill are developed in this paper. Size reduction was successfully achieved in the ultrasonic nip-roll device for a variety of materials. Ultrasonic comminution has repeatedly demonstrated the capability of producing fine particles from a variety of materials. A comparison between ultrasonic grinding and dry ball milling of limestone showed that the ultrasonic device produced much narrower size distributions than the ball mill. This trend is especially obvious in the coarse size range where few particles remain, and in the fine size range where overgrinding is prevented. This behavior might have some interesting applications in areas other than mineral processing like powder metallurgy or material science where narrow and controlled product sizes are required for the successful elaboration of high-technology ceramics and glasses. Ultrasonic comminution has a significant advantage in the accurate control of the product size.

Jan 1, 1993

By Hampshire MJ

The tailing retreatment project rated at 10 000 t/day commenced operations in October 1982. The operation consists of dredging, feed preparation, cyanide leaching and carbon-in-pulp (CIP) gold recovery followed by Zadra atmospheric stripping and electrowinning. For the first two years the operation was adversely affected by excessive cyanide consumption and low gold extraction. Investigations demonstrated that the very fine, or slime, fraction of the tailing was the dominant consumer of cyanide and dissolved oxygen. The plant flowsheet was subsequently modified by inclusion of 80 - 100 mm dia. cyclones for slimes separation and a 31 m dia. thickener for water recovery. Treatment of deslimed feed in the CIP plant has reduced sodium cyanide consumption from an average 1.85 kg/t to 1.15 kg/t. The reduced oxygen consumption by the CIP plant feed has resulted in higher dissolved oxygen levels, frequently reaching supersaturation after 4 to 5 h contact time. This has allowed much improved gold extraction from the existing CIP plant capacity. Gold extraction from the mixed pyritic siliceous tailing has improved from an average U prior to desliming to a current 57%. Investigations are continuing on the recovery of gold from the discarded slimes.

Jan 1, 1986

By T. E. Wakefield

Over several decades in Southern Africa the advance rates when sinking vertical shafts have declined significantly. The upside has been a substantial improvement in shaft bottom conditions and a commensurately improved safety performance, with an increasing number of shafts being sunk without fatalities and disabling injuries. This paper briefly reviews historical sinking rates and matches changed sinking productivity to the introduction of new sinking methods that have been adopted to eliminate/mitigate safety risks. Meeting the challenge of returning to historical advance rates whilst progressing in the quest for zero harm by utilizing three dimensional animated computer modelling is described. Making use of commercial modelling software makes it easier to evaluate different methods, sequencing, in shaft barrel ergonomics, and stage and shaft bottom layouts before procuring project plant and equipment. Benefits accrue not only in better communicating methods and configurations for detailed planning and design, but also during crew training. The traditional engineering ?as-built? drawing practice has been extended to the concept of an ?as executed? sinking model which seeks to capture operational experience and learning for future best practice. The paper concludes with some of the organizational culture challenges being overcome as this non traditional approach to shaft sinking optimization is being introduced.

Jan 1, 2009

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By Mark Gilliam

Control of true steel level in the tundish during casting is desired in order to maintain the correct pressure head and thus provide a stable flow to the mold. Also the control of tundish draining prevents slag carryover and can increase yield at each end of cast sequence. At Steel of West Virginia (part of the SDI Group), it was understood that to be able to measure the true steel running level and control the drain level at the end of casting would be a great benefit during production at their three strand billet caster. This paper sets out to show how an evaluation process was started to find the best method to determine steel level in the tundish and to prevent the steel level dropping low enough to allow slag to enter the mold. Also how the decision was taken and a real time molten steel measurement system was installed and by utilizing the resulting data in the process, how slag in the mold was removed as an issue, how lost production was reduced and how consistent steel level has provided constant casting speeds and improved stream integrity, all leading to realized quality improvements. Other areas discussed within the paper will be the training of operational staff, the difficulties to be overcome when first installing new equipment and how these teething problems were cured by close co-operation between the steel plant and the equipment suppliers. In conclusion the paper will discuss the production improvements achieved, production cost savings at the plant and how the generated data was integrated into the plants process control system.

Aug 16, 2017

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By I. Govender

Positron-Emission-Particle-Tracking (PEPT) has enabled the non-invasive observation of charge and slurry transport in model mills under operational conditions. We use high quality PEPT data to infer that the charge motion can be effectively described by a non-Newtonian granular fluid. An improved theory for slurry transport, including inertial effects, is presented.

Jan 1, 2012

By S. J. S. Ferreira

Anglo American Platinum's Khomanani 2 shaft changed over from down-dip mining to breast mining in 2004. The changeover was made to ensure that production targets were met, as it was said that predevelopment for down-dip mining was not fast enough to sustain the required ore reserves; nevertheless, production performance did not increase as expected. In this study a trade-off was performed between down-dip mining and breast mining on the Merensky Reef at Khomanani 2 in order to find the most suitable method for mining the Merensky Reef. Data was gathered by means of a literature survey, underground observations, and interviews with personnel as well as data from various departments on the mine. The two mining methods were studied and then evaluated in terms of the following criteria: safety, mining rate, cost and other factors which were identified as the main drivers of the mine. A scaling system was used to rate the performance of the two mining methods. Analysis of the results shows that down-dip mining and breast mining have the same safety performance ratings. Breast mining has a better mining rate performance than down-dip mining. Breast mining was found to be costly in comparison with down-dip mining, which has a good cost performance rating. The overall ratings of the two mining methods are very similar, with down-dip mining achieving a rating of 76 and breast mining 75.5 out of an optimum 102. Khomanani 2 currently practices breast mining, and with such a slight difference in performance rating between the two methods, it will not be worth changing over to down-dip mining as production is likely to be adversely affected during the changeover. Down-dip mining does, however, have potential for improvement in its performance rating. Further studies focusing on the improvement of the mining rate performance for down-dip mining are needed to see if this potential can be realized. If significant improvement can be made in the performance rating for down-dip mining, a changeover to down-dip mining can be reconsidered.

Jan 1, 2012

By K. Najim, D. Hodouin

"The raw ores which are processed in mineral processing plants exhibit very strong variations of their physical and chemical properties. As a consequence, the performances of the comminution and separation processes vary greatly from time to time. Model-based control strategies improve the performance of the plant; however, they require some form of adaptation to cope with the variations of the are properties.This paper deals with the use of adaptive techniques for the control of mineral processes. It begins with a survey on adaptive control algorithms including parameters estimation aspects. Then several examples dealing with crushing, rod, ball, autogenous and semi-autogenous grinding, flotation , drying and calcination processes are reviewed.IntroductionThe operation of the various processes of mineral processing plants (crushing, grinding, flotation, dewatering, etc.) is generally controlled using empirically tuned regulators of constant structure, such as PID controllers. To improve the operation performance, mineral processors try to implement specifically designed controllers, i.e. controllers based on plant dynamic models. Most of the time, these techniques improve the control of the mineral processing installations. However, modelling is a complex procedure because of the problems of measurement and data management, specific to this industry, and because of the variations of the model parameters. In this context model-based control strategies do not always bring the expected improvements or are sometimes discarded and replaced by more conventional techniques .The sources of variation of the dynamic behaviour of mineral processing systems can be classified into three categories: (I) the inherent changes of the raw ore properties (composition, grindability, mineralogical texture, etc.); (2) the process tuning modifications (grinding media loads, number of hydrocyclones, slurry level in flotation cells, agitation speeds, etc.); (3) the feedrate variation of the ore, water, chemical reagents, etc. All these factors change the fundamental properties of the process dynamics such as the grinding or flotation rates and the residence time in the equipment. The simplified linear models which are used to describe the process dynamics are not able to track the complex behaviour of the mineral processing systems when the amplitude of the sources of variation are too large. The mismatch between the model and the plant behaviour is then frequently a cause of model-based controller failures."

Jan 1, 1992

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013

By Scott Ellenbecker

The formation in Newmont Mining?s Phoenix Mine near Battle Mountain, NV contains high levels of abrasive quartzite as well as gold, copper and silver. Newmont started mining operations at Phoenix (formerly Battle Mountain Gold) three years ago and the planners knew they were working with a challenging geological formation. But as it turned out, it was more challenging than anticipated. Mine manager Mark Evatz said, ?Anything that touches Phoenix rock wears fast. The rock fights back here.? To contend with the hard conditions, Newmont uses Atlas Copco?s Pit Viper 271 (PV-271) blasthole drill. Because of the hardness of the rock, drilling at Phoenix requires hammer drilling and the mine uses Atlas Copco TD65 hammers with 171 mm (6.75 in.) bits. The mine?s PV-271?s are outfitted with a single 41 m3/min (1450 cfm), 2.4 MPa (350 psi), oil-flooded air compressor. Phoenix has six Atlas Copco PV-271 drill rigs plus an Atlas Copco DML and a DM45 midrange blasthole rig. The mine?s goal is to keep 3.6 Mt (4 million st) of muck in inventory to stay ahead of the shovels and support needed operational flexibility (ore control related). Drilling efficiency has been a continuous point of improvement since operations began at the mine. The single-pass depth capability of 16.5 m (55 ft) on the PV-271 helped with that. Originally, the plans called for 6-m (20-ft) bench heights, supported by 7-m (23-ft) drill depths, and time spent moving from hole to hole was eating up productivity. Drilling on that plan resulted in drilling an average of 14 m/h (47 ft/hour). When depths were changed to 13-m (44-ft) drill depth, supporting blasting of 12-m (40-ft) benches, they were able to use the single pass capacity of the PV-271. Performance increased to more than 18 m/h (60-ft/hour) an hour. Although the drill depth change largely supported the improvement, other aspects of continuous improvement associated with improved knowledge of the Pit Viper drills helped as well.

Jan 1, 2009

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Sun Ying, Zhang Jing, Li Qiuju

A new process of enrichment Cu in molten copper slag under electric field is presented in this article. The experiments were carried out in the laboratory on a kilogram scale. The mobility of copper slag was improved by the technique of carbon reduction. The effects of temperature, electric field strength and intermittent feeding speed were investigated on Cu migration. The results showed that the best experimental conditions were the temperature at 1523K, electric field strength was 1.5V•cm-1 and feeding rates was 15 g•(10min)-1. The copper content of the slag decreased below 0.6wt%. The process was compared to the traditional electric furnace process of slag cleaning, there was reduced the energy consumption and heat loss, and also harmful gas emissions such as SO2 and CO2, accompanied by improved the efficiency of slag cleaning.

Jan 1, 2016

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005