Search Documents

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

By W. K. Ting, A. Hasan

Mine stope is typically backfilled with cemented paste backfill, which provides a regional underground stability and also a reduction of aboveground tailings accumulation. During backfilling, a phenomenon known as arching occurs and affects the stress distribution of the cemented paste backfill. The change in temperature due to uncontrolled heat transfer from the surrounding rock mass and/or generation from hydration process complicates the stress distribution development of cemented paste backfill. This paper presents results of the investigation on the effects of hydration to cemented paste backfill behaviour when backfilled into a narrow wall model using uncemented paste backfill as controlled sample. The parameters considered include backfill type (cemented paste backfill vs uncemented paste backfill), curing temperature (30°C–60°C), and stress evolution during pouring, consolidation, and curing stages. Results show that uncemented paste backfill re-establishes arching effects more readily, with lower peak stresses and greater stress relaxation than cemented paste backfill, of which its behaviour is significantly influenced by hydration under elevated temperatures. The main outcome of this work is that hydration critically controls the stress-temperature response of cemented paste backfill, and the balance between hydration-driven strength gain and stress relaxation can be leveraged to optimise backfill mix design for safer and more efficient stope filling.

Jan 30, 2026

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By Joan Weinberg

Real output expanded at a 3.0% rate worldwide in 1987, a slightly lower pace than the 3.2% rate in 1986. The decline was accounted for largely by slower growth in the U.S.S.R. and the East European countries, as well as in the developing countries (table 1). According to the International Monetary Fund, output of industrial countries output grew 3.1% and rose most strongly in Japan, the United Kingdom, and Canada (table 2). U.S. economic growth remained at 2.9%, the same as in 1986. Consumer and government spending declined in industrial countries, while gross fixed investment: rent increased. This increase in fixed investment expenditures could be attributed partly to lagged results of some 1986 developments: the fall in oil prices, declining interest rates, and exchange rate changes. The U.S. budget deficit, as well as the large external deficits and surpluses among major industrial countries, hindered further growth .2 A report from the Organization for Economic Cooperation and Development (OECD) indicates that the impact of the October stock market crash was short-lived because it hit economies that were growing strongly, anyway.3 The growth of output in the developing countries slowed in 1987; however, output declined in the fuel-exporting developing countries. These countries have been adversely affected by weakness in oil prices and the depreciation of the U.S. dollar. The weighted average of inflation rates in industrial countries--as measured by the [ ] GNP deflator, was 2.9% in 1987, down from 3.4% in 1986. Prices rose 3.0% in the United States, up from 2.6% the previous year. Inflation for 1988 is expected to remain slightly higher in the United States than in Japan and the Federal Republic of Germany because of recent exchange rates changes and the elimination of slack productive capacity and labor in the U.S. economy. Prices in developing countries as a whole rose more than 10 percentage points in 1987. Higher import prices, caused by

Jan 1, 1988

By B. M. Larsen

Jan 1, 1948

By B. M. Larsen

Jan 1, 1948

By A R. Heath, I Arbuthnot

Feed slurries are typically flocculated in a thickenerÆs feedwell to increase the settling rate, underflow density and overflow clarity. High molecular weight polymeric flocculants are normally used, but present a number of challenges in terms of make up, dilution, delivery and mixing with the feed slurry.Various aspects of the flocculant dilution and delivery system have been studied with a combination of flow visualisation and computational fluid dynamics (CFD). An open topped flocculant dilution/mixing box has been developed to replace a conventional flocculant manifold, with improvements to the mixing, fault diagnosis and ease of determining the flow split to the various dosing points. The addition points to the feedwell have also been studied, both in terms of where the flocculant is added, and how. While conventional multi-hole spargers are effective in dispersing flocculant, they are prone to blocking and have been replaced by open-ended pipes. The required dispersion is provided by an efficient mixing element placed in the dilution port. Adding the flocculant into the feedwell dilution stream prior to mixing with the slurry also provides super-dilution of the flocculant that can further improve the flocculation process and reduce flocculant consumption.CITATION:Heath, A R and Arbuthnot, I, 2013. Advances in thickener flocculant delivery, in Proceedings MetPlant 2013 , pp 86-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021

By Peter J. Suardini

Over the last few years, researcher have been working on improving procedures for fine-coal (minus 150 microns) washability analyses. The effort was stimulated by past difficulties in obtaining accurate and reproducible results from the various commercial laboratories providing fined washability services. This paper contains the results from fine-coal washability testing, performed by Process Technology, Inc. (PTI), as part of a U.S. Department of Energy (DOE)-sponsored project. The testing focused on comparing the performance of a number of media options (i.e., aqueous solutions and organic solvents), as well as evaluating the impact of a number of procedural steps on separation performance. The paper summarizes PTI's recommended washability procedures for various size fractions and ranks of coal, and makes recommendations for future studies of certain phenomenon, such as void penetration and particle density changes, which are not well understood.

Jan 1, 1995

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

By Roy A. White

The development of a fire and rot-resistant coating treatment for mine timbers, along with the associated processing technology, is described. Included are a literature search, laboratory studies of polyimide-fungicide coatings, and leaching and fungus growth studies on coated wood blocks. Finally, an economic analysis is performed tor various levels of production.

Jan 1, 1977

By R. W. Diamond

PUBLIC debts, and the policies guiding public finance in Canada today, are in such a state that every intelligent citizen should be familiar with them, and should be concerned about them. None of you have robe reminded that taxes have already risen to a point where they both annoy and hurt you, but they should also alarm you; alarm you, not so much because of the taxation, but because of the mounting expenditures represented by that taxation. I have no hesitation, therefore, in presenting a paper dealing with public finance at a meeting of the Mining Institute, since all present are concerned,. both as individuals and as representatives of the industry. Moreover, it is important that engineers, particularly, should become better acquainted with the interlocking relationships of economics, public finance, government, and technology. While I am neither an economist, a tax expert, nor a chartered accountant, I shall try to tell you, from my viewpoint as an engineer and an interested voter, the story of public finance in Canada today and of certain causes and effects, and I shall venture certain conclusions. In doing so I may merit criticism by experts, but I will risk this in the hope that sufficient interest will be stimulated in the subject to persuade you, as individuals and as groups, to advance, or to institute, your own studies in public finance, and in turn to interest others. I hope that some of the ideas which will be expressed, or which may develop, will bear fruit. I fully realize that several eminently qualified men have spoken on this subject during recent months, and that many authoritative articles have been written. However, I approach it with confidence, because I propose speaking to you not as an authority, bur as one of you, having similar interests and similar engineering knowledge, who only a few months ago became particularly interested in the subject, studied it, and who now sets before you a summary of his findings, with the conviction that the situation is so serious that constructive planning and constructive action by all thinking citizens are imperative.

Jan 1, 1939

By G. Merle, David L. McKay, Elmar Randveer

"THE ENGINEERING AND TECHNICAL SERVICES department is responsible for supplying the following services:1. Administration and co-ordination of the work required for capital projects.2. Engineering, design and drafting services for inplant changes or improvements as requested by the operating• and maintenance departments.3. Rock mechanics.4. Preparation of plans and layouts required for efficient extraction of the ore as mutually agreed with the mine operating departments.5. Mine planning and long-term schedules in co-operation with the mine operating departments.6. Grade control (long term and short term) and the preparation of ore and waste removal schedules to maintain a uniform grade of mill feed. This also includes the calculation of metal reserves and metal production forecasts.7. Surveying, underground and surface.8. Operations research at the mine site.9. Industrial engineering.10. Chemical analyses and assays.11. Instrumentation.12. Environmental control.A staff of approximately 35 supervisors, engineers and scientists, and 80 technicians, supply the foregoing services. Consulting engineering and drafting firms are used to supply specialized services and technical personnel in-house at Timmins to handle overloads on capital projects under the direction of Ecstall engineers.The operating and maintenance departments depend on the engineering department to supply engineering, design and drafting services for any new facilities or for any planned alteration to existing facilities. To do this efficiently requires a high level of communication and co-operation with these departments. This has been a major factor in developing the present organization of the department shown in Figure 63.The organization is predicated on a strong central technical and engineering resource from which personnel can be assigned responsibilities for different projects, and in different areas, as the work load demands. Job satisfaction is very high because of the variety and challenge in the tasks. Additionally, participation in projects with production and maintenance personnel broadens each technical employee's knowledge of operating and maintenance problems."

Jan 1, 1974

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011

By J. E. Schiller, S. E. Khalafalla

Due to its unique surface properties, magnesium oxide (MgO) is an excellent medium to filter asbestos and other suspended solids from water. MgO operates up to twice as long as a sand filter before backwashing is required while flow rate and filtrate clarity are as good or better with MgO.

Jan 1, 1984

By W. J. Campbell

This report by the Federal Bureau of Mines Particulate Mineralogy Unit recommends mineralogical definitions and identification-characterization concepts for selected silicate minerals and their asbestiform varieties. Precise definitions acceptable to mineral analysts, regulatory personnel, and medical scientists are essential because of the present lack of conformity in terminology concerned with measuring and controlling asbestiform particulates and their related health effects. Because of the complexity and variability of crystal morphology in different mineral groups, the descriptive terms are generally explained by illustration rather than by numerical values. Applications and limitations of several analytical techniques for particulate identification and characterization are discussed.

Jan 1, 1977

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023