Search Documents

Room-and-pillar mining at White Pine started in 1953 from a sub-outcropping orebody that gently dips to 1000 m depths in a distance of about 6 km. High horizontal stresses were recognized in the mid-1960s which had obvious stability impacts when viewed in combination with the increased overburden stresses. Modifications in conventional room-and-pillar design were introduced through the years on a trial-and-error basis to help overcome stability and resource recovery problems. These modifications were based on pressure arch concepts using pillar yielding and/or pillar recovery, and on mine layout orientation to minimize stress impacts. While some of these modifications were successfully applied in some areas, they failed in others. Through the years, visual observations played a major role in panel design with contributions from stress measurements and analyses. However, the down slide in the copper economy during the 1970s and early 1980s resulted in a loss of interest in the application of these concepts. This paper reviews ground control problems and presents the results of recent stress measurements and computer analyses. They shed light on the importance of using yield pillars and mine layout orientation to control stresses at depth.

Jan 1, 1993

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

The recent trend of installing flotation cells with volumes as large as 200 m3 in concentrators is driven mainly by economic considerations such as lower capital, operating and maintenance costs. Despite the economic advantages, the metallurgical benefits from these large cells have not yet been fully realised by the industry. This is mainly due to the lack of understanding of cell operation, viz cell mixing and hydrodynamics, gas dispersion and froth transportation behaviour in large cells. There is still no rational basis for selecting optimum cell operating conditions and down-the-bank operating profiles. The relationship between cell operating conditions and metallurgy is not well established. This has resulted in poor utilisation of cell capacity in many operations. The present trend of installation of fewer cells in a bank requires each cell to be operated very efficiently. Optimisation of cell operation provides an opportunity for significant metallurgical improvements in a flotation circuit with minimal capital expenditure. Extensive work on optimising of cell performance has been carried out at various Teck Cominco operations in Canada, Peru and USA. Three different levels were involved in this work. The first level was aimed at identification of cell operating conditions for optimum mixing and hydrodynamics, gas dispersion, entrainment and froth flow behaviour in individual cells. The objective of the second level was to identify the optimum bank operating profile for cells down the bank in a circuit. The third level then focused on controlling these cell operating conditions and bank operating profiles for tighter control of concentrate grade and recovery for optimum bank metallurgy. This paper presents some of the major findings at all three levels and demonstrates the importance of each level in optimising the performance of flotation banks installed with large cells.

Jan 1, 2005

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By Hwa-Soo Park, J. K. Yoon, Hoseok Nam

In a thin slab casting process, control of fluid flow in mold is particularly difficult due to the high casting speed and large aspect ratio of the mold and the understanding of the fluid flow motion as well as heat transfer in mold is regarded as the most important information because the melt delivery is directly related to the problems of shell growth nonuniformity, surface turbulence and mold powder entrapment. A mathematical model has been developed for the coupled analysis of fluid flow, heat transfer and solidification in funnel type mold using finite volume method based on a body fitted coordinate and the characteristics of the transport phenomena in the mold of thin slab caster were analyzed by numerical simulation. As a result of simulation, the basic flow pattern is characterized as four large recirculations and two small eddies near the narrow faces of mold, which is somewhat different from that of parallel type mold or other conventional slab caster. The heat transfer model accurately predicted the mold positions susceptible to cracking as a result of thermal stress and the predicted shell thickness shows good agreements with the measured shell thickness on breakout products. We also investigated the influences of some operation parameters such as casting speed, nozzle type, submerging depth and mold material on fluid flow, heat transfer and distribution of solidifying shell and various information for the determination of optimal operating conditions were obtained.

Jan 1, 2000

By S. Sundarraj

The morphological transition between columnar and equiaxed structures is an important solidification phenomenon frequently observed in castings, especially complex parts with varying cross-section, The mechanical properties and the occurrence of defects such as hot tears are strongly dependent on the structure formed in the casting. Hence, it is important to understand the conditions leading to columnar or equiaxed structures. Although extensive work has been done in modeling solidification systems, almost all of the existing models are based on the assumption that the structure formed in the casting is either purely columnar or purely equiaxed. Prediction of the columnar-equiaxed transition (CET) requires a solidification model which accounts for the formation of both columnar and equiaxed structures, along with related microscopic and macroscopic solidification phenomena. In this paper a CET model is presented which: (i) takes account of both columnar and equiaxed structures, (ii) accounts for macroscopic heat transfer coupled with microscopic phenomena such as nucleation, growth and microsegregation, (iii) satisfies solute conservation, and (iv) is easy to implement in commercial finite element and finite difference software. The proposed model predictions of CET have been validated with available experimental results for a uni-directional solidification of an aluminum-copper alloy. A sensitivity analysis has also been carried out to determine the effects of various parameters on the CET model predictions. The model is being extended to other alloy systems and more complex geometries. This work will be published in due course.

Jan 1, 1996

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Pablo Segarra, José Ángel Sanchidrián, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD) data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al. (2018) and Navarro et al. (2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave- in rock and cavity. From it, an application for the geotechnical rock condition of orebodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting.

Feb 1, 2020

By H. Assadi, S. Reutzel, D. M. Herlach

Intermetallics exhibit unique solidification behaviour due to their chemical longrange order. This includes, for instance, generally slow solidification kinetics, and in some cases, an anomalous partitioning behaviour. In the present work the electromagnetic levitation technique - complemented by theoretical modelling - is used to explore various aspects of this behaviour, as observed in solidification of B2 phase in undercooled melts of the Ni-Al system. Moreover, a phase-field model is developed and used to illustrate the effect of chemical order on the solidification kinetics of a B2 phase in a model system. The phase-field model provides an additional basis for the simulation of solidification microstructures in intermetallic forming systems. Both experimental studies and theoretical work signify the role of chemical order in solidification of intermetallics.

Jan 1, 2006

By Karin Bäppler

A new polyhalite fertilizer mine is currently being developed in the UK by Anglo American Crop Nutrients. The project includes the construction of a Mineral Transport Tunnel almost 37 kms long to house a conveyor belt that will move polyhalite from the production shaft at the mine to a materials handling facility at the port. The project sets a new standard in terms of an ultra-long tunnel drive and sustainable, environmentally friendly and efcient material transport. The paper highlights in particular the . m diameter TBM in use for the construction of the ultra-long tunnelling section.

Jun 23, 2024

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By G. J. Allen

Kennecott Copper Corporation's Nevada Mines Division initiated a program to stabilize the inactive portions of the tailings disposal area and perimeter dikes in 1946. To date, approximately 1,000 acres have been stabilized with vegetation and ground cover.

Jan 1, 1978

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

By J K. Claflin, S R. La Brooy

A case study from a current Ausenco project is presented to demonstrate the importance of maintaining high carbon activity to illustrate the driving force for plant improvements such as a carbon regeneration kiln upgrade.This paper revisits the factors that influence carbon activity for gold loading, with emphasis on deactivation by organic solution components such as flotation reagents.Kiln process design requirements for effective thermal regeneration are reviewed including the interaction of parameters such as temperature, kiln atmosphere and residence time.The different types of kilns that have been used for carbon reactivation are described. A check list is provided of what to look for when purchasing a carbon reactivation system for dealing with severely fouled carbon. This covers the ancillary equipment as well as the kiln itself.While the effectiveness of the carbon reactivation kiln is vital to maintenance of high carbon activity it needs to be remembered that this is only the end of pipe solution. It is also important to ensure that reagents such as frothers and flotation collectors are appropriately chosen to maximise recovery and at the same time minimise carbon deactivation.CITATION:La Brooy, S R and Claflin, J K, 2013. Carbon management in a high gold price environment, in Proceedings MetPlant 2013 , pp 455-467 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By V. E. Edlund

This report presents the results obtained in a study of the technical feasibility of recovering a usable pig iron by pyrometallurgical treatment of typical copper reverberatory slags . The iron in the slag was readily reduced with carbon , but the copper and sulfur content of the metal was best controlled by a three - stage procedure comprising ( 1 ) melting the slag with pyrite to remove copper as a low- grade matte , ( 2 ) smelting the partly decopperized slag with fluxes and carbon to reduce the iron , and ( 3 ) refining the impure iron alloy from step 2 with a flush slag to remove sulfur and residual copper . Laboratory - scale tests demonstrated that washing with 8 wt pct of pyrite lowered the copper content of a typical reverberatory slag from 0.58 to 0.12 Subsequent smelting of a mixture composed of 70 pct decopperized slag , 25 pct lime , and 5 pct coke reduced 84 pct of the iron to metal containing 2.27 pct sulfur . This metal then was successfully desulfurized by treatment with a basic flush slag to produce a finished metal that contained , in percent , 93.5 Fe , 0.02 S , 0.26 Cu , and 4.9 C. Overall recovery of iron under the conditions of trial was about 80 pct . This could be increased if higher tolerances for copper could be accepted . Commercial processing would be accomplished in three furnaces with molten materials passing from one to another . Currently produced smelter slag could be treated fairly inexpensively , because the molten product would require only a little additional heat to produce an iron byproduct that undoubtedly would be attractive to local foundries .

Jan 1, 1964

By Subhash B. Bhagwat

No economic activity would take place without human ingenuity, driven by our needs and wants. Economic activity is made possible by the energy from fossil and other energy sources, our technological hardware, the buildings and infrastructure made from materials such as metals, plastics, wood, water, and numerous industrial minerals. Industrial minerals are difficult to define; however, they generally include utilitarian minerals other than metals and fuels. Some of the industrial minerals form an exception to this categorization and, as explained elsewhere in this book, belong to more than one category because of the manner in which they are used. Industrial minerals are so numerous, and their applications so ubiquitous that they often do not receive the attention given to metals or fuels. Nevertheless, without industrial minerals, many of our most fundamental economic activities such as construction of our cities and towns, control of floods, transportation of our people, the search for minerals, the smelting of metals, and the delivery of supplies of clean water would be impossible. How then do we assess the economic importance of such a variety of materials lumped together under the general designation of industrial minerals? The price per ton or the total amount consumed do not satisfactorily explain the relative value of these materials to the economy. For example, the current price of limestone is about $5/t and the price of fluorspar is about $190/t. However, nearly 1.1 Gt of limestone, valued at about $5.5 billion, are consumed in the United States annually, compared with 590 kt of fluorspar, valued at about $1 12 million. It would not, however, be accurate to conclude that the mineral with the higher total value is always more economically important. Many other questions must be answered before making judgments of this type. These questions include how many people are employed in the production, processing, and distribution of the mineral? How is the mineral used? Is it partly or entirely imported? Where do the imports come from? How is the mineral transported? Is the mineral considered critical to national security? Is there a substitute material available in case the mineral supply is interrupted? Where would the substitute be produced? What would be the basic material from which the substitute will be produced? Even when these questions have been answered satisfactorily, the economic importance of the mineral is not completely known until the consuming sectors are studied as well. For example, even though the manufacture of fighter aircraft is vital to the national security, it employs only a fraction of the number of people employed in the housing and construction industry or the automobile industry or the appliance industry. Mineral commodities consumed in these latter sectors of the economy are more significant than those consumed in the production of fighter aircraft, because nearly two-thirds of the Gross Domestic Product (GDP) depends on the purchasing power of individual consumers. In comparison, the entire defense budget accounts for only 6% of the GDP. There is no easy way to present the importance of industrial minerals to the US economy because most minerals have diverse applications and products made from industrial minerals often con- tribute to the production of other goods and services. One way of highlighting the value of a mineral would be to relate it to the GDP reported by categories such as construction, machinery, stone, clay and glass products, electrical and electronic equipment, paper and allied products, and chemicals and allied products. These GDP categories represent industries fundamental to the economy totaling $644 billion, or about 12% of the GDP in 1990. However, these categories are not convenient for discussion of the many minerals that are used in our complex economy. In a general way, minerals are the 5% of our economy that make the other 95% possible. This chapter, therefore, discusses a selected few industrial minerals to illustrate their importance to various sectors of the economy.

Jan 1, 1994