Search Documents

By K. Fuenkajorn

Geomechanics and geohydrological considerations for the seal design for mine openings are presented. Design guidelines derived from laboratory and in-situ experiments are proposed. The results suggest that seal design, specifications and material selection should be site-specific. Performance requirements for a specific seal location should be identified. Evaluation of sealing effectiveness should be made on the entire seal system, i.e. seal, seal-rock interface, excavation-induced damage zone and the surrounding rock.

Jan 1, 1997

By B. Petkof

Olivine has been an accepted industrial mineral for the last 50 years. Its initial acceptance was based on the recognition of its refractory properties by European research workers in the middle to late 1920's. Initial U.S. olivine production began in the early 1930's in North Carolina and continues there today. Olivine also is produced in the State of Washington and in other countries.

Jan 1, 1982

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By III, Peter J. Rogers, J. Gordon Ogden

A study is described which attempts to identify the chemical factors of common concern to environmental and exploration geochemistry as indicated by recent work in both disciplines in Nova Scotia. Cores taken in lake sediments define geochemical baselines for the modern and pre-industrialisation periods. The investigation of lake and stream drainage indicates the presence of numerous chemical and organic factors that can be attributed to man's activities, such as construction and energy consumption. Geochemical surveys of lake and stream sediments are used to locate potentially toxic, high risk areas in Nova Scotia. Rapid change occurs in most surface drainage systems with the possibility of numerous chemical reactions taking place. It is found that spatial and temporal variations in the chemistry of modern and recent sediments are of interest to exploration and environmental surveys.

Jan 4, 1992

By H. A. Steane

THIS PAPER describes the re-grind section in the 2,000-ton per day, lead-zinc flotation mill of Canadian Exploration Limited, near Salmo, B.C. There are two re-grind units in operation, one in the lead circuit, and one in the zinc circuit. In each unit, the rougher concentrate is re-ground ahead of the cleaning circuit. These re-grind units have made valuable improvements in the concentrate grade, and with no loss in recovery by over-grinding galena or sphalerite. Since the initial installation of this re-grind section, the plant throughput has been increased gradually from 1,600 tons to 2,000 tons per twenty-four hours, and, as shown by the screen analysis of mill tailing, a coarser overall grind has been accepted, from 55 per cent to 45 per ?cent minus 200 mesh. There has been no increase in grinding capacity, but two mills have been taken from the main grinding circuit and used for the re-grind circuit.

Jan 1, 1958

By T. A. Rickard

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To 'punctuate' is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical, or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. .'The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness; proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; 'on the other hand, paragraphs of. excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By Newell Alford

THE data in this paper were collected to show both the volume and speed with which bituminous mines have indefinitely suspended operation while economic advantage in the industry has so gravely declined. The study was limited to the bituminous coal-mining states east of the Mississippi River, wherein conditions affecting production and demand are more common respectively to all of the mining districts included and represent about 95 per cent of the nation's coal mining. Data for the compilation of these statistics and for the construction of these graphs have been obtained in all cases from state mine depart-ment reports, except from those of Ohio and Virginia. In Virginia essential individual mine data were secured from an authentic source, but no individual Ohio mine information is obtainable, because all Ohio fact-gathering agencies are prohibited by law from revealing such data. In other states the facts were tabulated and later checked with the cooperation of Chief Mine Inspectors. In all, excluding Ohio, over 17,000 individual annual mine returns were examined. Special infor-mation was secured from each state mine department about suspensions in 1932. Accurate information was not available from all states about mine abandonment due to exhaustion of coal reserves, and while these were completed for several states, it has not been shown because it was not perfected for all states. However, the total observed sample was comprehensive enough to show that exhaustion accounts for a very limited part of the suspended production. Wherever mention is made of "suspended production" the largest annual output of the mine in the five years prior to suspension has been taken as the measure of its probable production had it continued to operate. A mine is not regarded in this category, as having suspended, when it merely ceases to produce. The word "suspension" is used only where there is a complete abandonment of activity for an indefinite period, as evidenced by the fact that both ventilation and pumping are discontinued.

Jan 1, 1933

By H. W. Gillett

UNLIKE most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are-I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital-it is not, those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his: approach to the problems of metallurgy, his broad-mindedness and fair-ness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude-his refusal to accept them as masters-that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united.

Jan 1, 1939

By Cloyd M. Smith

A FEW years ago, the Ventilation Committee established the practice of presenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measurements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies.

Jan 1, 1949

"The method of conveying ore from the ore-pocket at the shaft collar to the railroad ore bins, whence it is transported to the reduction works, is by cars with electric haulage.The cut shows the car coupled to the electric locomotive at the moment of dumping into the railroad ore bins.The locomotives used are of several makes, usually having two 12 ½ h-p. motors of a rated draw-bar pull of about 1,200 lbs., using 500 volts D. C. Track gauge is 30 inches, and speed is six miles per hour.The car holds two skip loads-10 tons—and has sides opening outwards the full length of the car, for rapid side-dumping. One man operates car and motor, and loads and unloads the car. The trolley pole runs in both directions without reversing.Loading is clone by operating a valve connected to a compressed air lift, which raises and lowers a gate in the ore-pocket chute, the ore running by gravity into the ore car spotted under the gate of the chute. Dogs hold the sides of the car in place at the bottom, the tops of the sides being hinged, and a hand lever releases the dogs, permitting the sides by the pressure of the ore against them to open at the bottom.With little manual effort one man does the work which was formerly done, when hoisting ore with cars and cage, by 10 men under laborious conditions."

Jan 1, 1913

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By D Lozada, A Salazar

Geometallurgy is a tool that, for more than a century, has been present in the implicit operations of mineral beneficiation. There’s a need to understand the characteristics of the material to be processed. This has led metallurgists to ask geologists what type of rock and mineralogy is entering the Beneficiation Plant and vice versa. The geologist needs to understand the beneficiation process in order to be able to carry out the production programming. The paradigm is whether geometallurgy can be applied to small-scale mining or if it is only aimed at large companies that invest millions of dollars to conduct studies. With this work, we provide an example of how geometallurgy can help improve the processes of a small mining company located in Ecuador (South America). We performed characterizations of geological and mineralogical and metallurgical tests in universities and the National Research Institute of Geological Metallurgical Mining. The origin of the theme is based on the fact that gold has been detected in the final tailings. The flotation concentrates meet the standards in terms of the content of economically profitable metals, but this isn’t the case with regards to the percentage of arsenic, which has hindered sales. The hypothesis is: conducting technical and scientific research will optimize the metallurgical process for the recovery of gold and concentrates. The referential framework is the mining geology of the Bella Rica District, current status of the Beneficiation Plant. In the theoretical framework there are parameters of the veins, comminution operations, gravimetric concentration, flotation, and cyanidation. The methodological framework contemplates the characterization of the gold ore, the chemical, mineralogical, textural, metallurgical analysis and the interpretation of the results. Thus, the design of a geometallurgy model of the deposit, with its main characteristics, is a conclusion that serves as a basis for the proposal of the optimization of the metallurgical process.CITATION:Lozada, D and Salazar, A, 2018. Geometallurgy applied to small-scale mining: a case study, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

By Chamila Jinendra Nanayakkara, Nimila Dushyantha, Amila Sandaruwan Ratnayake, Gayithri Niluka Kuruppu

Rare earth elements (REEs) are key ingredients in many advanced materials used in energy, military, transportation, and communication applications. However, the prevailing geopolitical dynamics and the rising demand for REEs have rendered the reliance on primary REE resources susceptible to future supply disruptions, posing a substantial risk to the availability of these elements for numerous applications. Therefore, it is imperative to undertake substantial initiatives in the extraction of REEs from secondary sources on a large scale to ensure the resilience of the supply chain. Permanent magnets, lighting phosphors, and nickel-metal hydride (NiMH) batteries are among the secondary sources with high potential for sustainable REE extraction. This review assesses the extraction potential of REEs from the aforementioned three secondary sources and their leaching kinetics and thermodynamics aspects. More importantly, state-of-the-art different existing kinetic models employed in rare earth (RE) leaching were well discussed for a better understanding of the REE leaching reactions. Furthermore, the optimized leaching parameters related to this kinetics were described, and various RE recovery methods were comprehensively summarized. These processes facilitate to managing one of the fastest-growing solid waste streams by minimizing environmental impacts and producing critical metals, including REEs via circular economy approaches. The recovery of REEs from secondary sources aligns with numerous United Nations Sustainable Development Goals (SDGs), particularly in the renewable energy sector for climate change mitigation. Consequently, this trash-to-treasure urban mining concept to transforming e-waste into a valuable resource for REE recovery emerges as a pivotal element within the REE industry.

Dec 28, 2023

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By William Wargo

The basic reason for lining underground cavities is to keep the cavity open during its useful life by providing adequately for the support of the surrounding rock and for the necessary degree of water tightness. This covers the entire field of support methods from the simpliest timber support to reinforced concrete in all its variations as applied to tunnels, galleries or shafts. The problem involved in the design of more efficient and economical lining systems for even bigger cavities has been magnified by increased speed of advance made possible by better blasting tecniques, improved tunneling machines and more efficient material handling. Tunnel lining today requires a disproportionate amount of time and money compared to other operations mostly due to the manuel labor involved in its installation. One solution to this problem is the developement of an entirely new concept in tunnel lining designed notoonly to overcome this bottleneck but also to open up the field for further increases in speed of advance. This new lining system acts first as a fast protective armour then becomes the concrete metal form and ends up as reinforcement sheet inside the concrete lining. This system developed and manufactured by Bernold A. G. of Switzerland since October 1968 has been installed in 25 applications in Europe under all ground conditions from stable rock to unconsolidated ground.

Jan 1, 1970

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011