Search Documents

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By G McCullough, B Mutsaers, J Jessop

"*This is an abstract only* Geometallurgical initiatives have demonstrated considerable value to operations that have trialled them. However, it is extremely difficult for these initiatives to become properly embedded into the operations and for that value to be realised on an ongoing basis.This paper will explore some of the historical reasons why this is the case. Some of these reasons include the limited tools available to manage an integrated operation. These, in turn, have resulted from poor communications infrastructure, inadequate sensor capability and the way technical mining software has evolved over the last 30 years.This paper will then investigate how the evolution of technology in recent years can help overcome these constraints and compare progress with similar industries.CITATION:McCullough, G, Mutsaers, B and Jessop, J, 2013. Obstacles to embedding geometallurgy decision-making into operations and how to increase maturity of this critical capability, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 139-140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were undertaken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 2010

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By Michel Fillon

Hydrostatic assistance is a commonly used method to improve limited load carrying ability of tilting-pad thrust bearings during transient states of operation of the vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves etc.), it also requires manufacturing of special recesses/pockets at the pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up of the machine and form a hydrostatic film between the pads and the collar. There is a quite wide variety of geometry of recesses (shape, depth, size) met in practical large bearing applications. The presence of a hydrostatic pocket (usually located in the sliding surface above the pivot area, where thin film, high oil pressure and temperature are observed) affects bearing performance under hydrodynamic operation. In theoretical researches, there is an almost common practice not to include hydrostatic recess in THD or TEHD analysis. This is probably due to the problems with obtaining solution for oil film geometry with pocket, with pocket depths order of magnitude larger than gap thickness. In this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of ltaipu power plant. Bearing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket.

Jul 31, 2018

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018

By Jr. Wallace

This paper describes the importance of mine ventilation and air conditioning in the operation of a nuclear waste repository. It discusses the impact of ventilation on determining the number and size of shafts and access drifts to and within a repository horizon. The paper also describes the need to maintain separate ventilation systems for waste emplacement and construction operations. The requirement to have filtration capabilities for exhaust air from waste emplacement areas is discussed. Because radioactive high level waste will induce high temperatures in the emplacement drifts, the ability to cool an emplacement drift for re-entry requirements is important. The paper discusses strategies to cool an emplacement drift and the possibility of using continuous airflow to control temperatures in these drifts.

Jan 1, 1991

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By George A. Calboreanu

In order to overcome drilling and tapping of high hardness wear resistent material in slurry pumps, most of time mild steel inserts are mounted in the mold and after pouring they become an integrated part of the casting. This process is limiting the size and design possibilities of slurry pumps and efforts were made to drill and tap the hard iron itself. The paper will present practical results obtained in drilling and tapping Cr-Mo wear resistent material with hardness in excess of 700 HBN. The life time of the slurry pump parts used in hazardous waste fuel transportation with high slurry velocity and 15% solid loading some of it being quartz, increased 2.5 to 6 times.

Jan 1, 1996

A comparison of gold, platinum and sulfide ion selective electrodes was made in this investigation for determination of Eh in solutions containing sulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. In addition, the sensitivity of each electrode towards changes in sulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration of sulfide ions. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion, HS-, concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion, S-, activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of sulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1990

By M. J. Kirwan

[There have been large increases in the oil production and casing-head gas production of certain wells on the Quinn dome (northern part of the Lyons-Quinn field of Oklahoma) caused by large volumes of gas under high pressure entering Vie productive oil sand, The oil production of sore of the leases in this part of the field temporarily increased over 100 per cent within a few days after gas entered the oil sand among the leases that had the greatest increases in oil production wore those on which no gas wells were drilled but which were located up-elope on the structure in reference to gas wells on adjoining properties. It is conservatively estimated that 1,444,000,000, cubic feet of gas entered the productive oil sand and, up to January 1, 1924, caused an increase of about 950,000 barrels of oil from this sand. The casing-held gas volumes of a number of wells producing between 25,000 and 75,000 cubic feet of gas per day increased to several hundred thousand cubic feet and a few walls increased to nearly two million cubic feet per day after extraneous gas entered the oil sand from which the wells were producing.]

Jan 1, 1924

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By T. T. Tomimatsu

This? Bureau of Mines paper discusses the corporate structure dynamics, methods of financing, and financial assessment approaches that should be utilized to evaluate the economic health of the coal industry. It suggests rates of return and other measures of corporate economies necessary to attract capital required to finance emerging coal demand, plus impact of coal sales to total revenues. The study illuminates the activities of 30 selected coal-producing companies, including their subsidiaries or affiliates, that were responsible for approximately 60 percent of the total U.S. production in 1974. The selected firms are not all primary coal producers; many of the larger producer's are classified by the financial institutions as petroleum, metal, and steel producers, public utilities, or chemical industries. The bituminous coal industry is highly competitive as to price, service, and quality of pronuct and is subject to competition from other noncoal energy sources. The top 15 bituminous coal-producing companies mined about 46.6 per-cent of the Nation's total production in 1974, and the balance of approximately 3,885 companies were responsible for the rest of the production. Thus, the U.S. bituminous coal industry is not an oligopoly. Today, about 65 percent of the Nation's total coal production is consumed by electric power utilities and 26 percent by steel, space heating, and other industries; the balance of 9 percent is exported.

Jan 1, 1976

By Edward L. Burwell

The Bureau of Mines conducted laboratory experiments to determine the change during retorting in the apparent permeability and the degree of compaction of beds of broken oil shale. Grades of oil shale studied ranged from 20.6 to 46.7 gallons of oil per ton (gpt), and the simulated overburden pressures applied to the shale were from 300 to 900 psi. Linear regression analysis of the data produced equations describing the response of the oil shale. Oil shales of approximately 20 gpt experience only minor apparent permeability reductions under test conditions, but richer shales (30 to 50 gpt) lose essentially all permeability. The permeability reductions were accompanied by corresponding decreases in bed height that ranged up to 37 percent of the original bed height.

Jan 1, 1974

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

By G. Akdogan, C. Bergmann, C. J. Coetzee, Q. G. Reynolds, S. J. Baumgartner

Submerged arc furnaces (SAF) are used extensively in the production of ferrochrome, where charge material – consisting of mixtures of carbonaceous reductants, fluxes such as silica, and ore in the form of pellets – is fed through chutes into the vessel. The feed typically forms a thick bed or ‘burden’ of solid particulates above a bath of molten material below. This burden layer surrounds three electrodes, which are typically arranged in a triangular configuration in circular SAFs. A major challenge in the industry is the availability of sought-after reductants, volatile market conditions, and increasing electricity tariffs in South Africa. A good understanding of the physical properties of the raw materials in the charge is therefore of great value in order to best deal with the reductants available at any given time, and thereby maximising furnace throughput. This paper presents a study of the effects of different particle properties on particle flow behaviour relevant to SAF operations. Discrete element model (DEM) simulations were used to estimate the sensitivity of the particulate flow of beds of charge material to properties such as the coefficients of friction, particle shape and size, and others. The present study lays the groundwork for the development of full DEM models of the SAF that will greatly improve understanding of the flow of complex mixtures of solid particles in the submerged arc furnace, and how the relative physical properties of each component in the charge can influence electrical behaviour of the burden.

Sep 1, 2021