Search Documents

By O. A. Lima

Effective solids suspension is a necessary precondition for particle collection, and solids suspension is largely dependent on the hydrodynamics of the flotation cell. This study attempted to correlate the status of the suspension of apatite particles of different sizes in a Denver laboratory flotation cell versus the impeller rotational speed (N) adopted to operate the machine. The latter variable (N) influences the impeller capacity to lift the particles from the bottom of the tank and also to disperse them throughout the volume of the vessel. Such an impeller capacity can be characterized by the critical impeller speed for the accomplishment of solids off-bottom suspension (Nz) and also by the velocity of the radial water flow discharged by the impeller (U) divided by the particle terminal settling velocity (Us). This way, the status of the suspension of apatite particles inside the flotation cell can be characterized by one of three categories: ?segregation? (N/N2 < 0.60 and Us/U > 0.08); ?suspension? (0.60 = N/N2 < 1 and 0.06 < Us/U < 0.10); and ?dragging? (N/N2 = 1 and Us/U = 0.03). The range of impeller rotational speed (N), which was able to suspend the finest particles (Dp = 90 µm), was unable to suspend the coarsest particles (Dp = 254 µm). Conversely, the high value of N (N > 1,300 rpm), which is adequate to suspend the coarsest particles, may promote the entrainment of the finest particles to the froth layer.

Jan 1, 2009

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011

German manufacturer DBT signed a contract to supply a sixth automated-plow long-wall system to Shenyang Coal in Liaoning province in northeastern China. This most recent order occurred just weeks after DBT signed a contract to deliver a fifth automated-plow longwall system to Datong Coal in Shanxi province. The plow will go into service at Shenyang Coal’s Hongyang Mine. Mining conditions at the mine, coupled with DBT’s advanced automated-plow technology, means that the system has the potential to become one of the world’s most productive thin-seam longwalls.

Jan 1, 2004

Study to develop a new and more cost effective equipment system, incorporating a winch-pulled dozer blade, for leveling spoil and performing reclamation of area strip mines.

Jan 1, 1975

By J. L. Carr

On average, one to two fatalities occur every year when a miner is struck or pinned by a continuous mining machine (CMM). Proximity detection systems offer an effective means to prevent these types of injuries and fatalities by sensing the presence of a miner and automatically disabling machine motion. The Mine Safety and Health Administration (MSHA) is expected to finalize a regulation that would require the use of proximity detection systems on all CMMs. Approximately one-fourth of all CMMs in use in the United States are already equipped with such a system. The use of these systems will save lives, not only by automatically preventing accidents but also by acting as a tool for educating miners and reinforcing safe work practices. Researchers at the Office of Mine Safety and Health Research (OMSHR) have conducted a series of field evaluations to quantify the performance of these systems in an underground coal environment. These field evaluations measured the distance at which the warning and stop zones were activated. The technology provided consistent activation of the warning and stop zones under many of the conditions tested. However, some performance inconsistencies were observed which present opportunities to improve the reliability of proximity detection system technology. Some of the notable variables that caused significant changes in performance and should be considered in the design, implementation, and use of proximity detection systems include interaction with the trailing cable, performance changes during tramming, and orientation of the miner-worn component.

Feb 23, 2014

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

By John K. Wood

The development of an expanded cement product represents a major advance in the technology of roof control systems. Such a product is gaining recognition as a valuable tool in today&apos;s cost- conscious coal mines. The National Coal Board&apos;s Bretby Research Lab, in conjunction with Polement Ltd., developed the first lightweight cement for use in the mines of the United Kingdom. The product, Aqualight, is a low-density (about 12.5 PCF) cement with a typical compressive strength of about 19 p.s.i. The final product increases in volume by approximately 15 times its dry powder volume. Aqualight gels in about 2 minutes, becomes self-supporting in 15 minutes, and fully cur& in 24 hours. When subjected to a load, the "cells" within its bubble structure collapse so that the product gains in density and compressive strength while retaining its integrity. Traditional methods to contain and support roof fall cavities through cribbing and blocking are both dangerous and labor-intensive. Aqualight represents a significant advantage over such traditional methods. It is non-toxic, non-cmbustible, and very easy to install. Aqualight can be pumped to the worksite from re- mote locations (as much as 600 feet), thereby reducing danger to men and equipment. Addition- ally, the strength of the cured product can be varied by adjusting the expansion ratio and resulting density. A compressive strength of 150 p.s.i. can be obtained in this manner. Although primarily designed to fill cavities resulting from roof falls. Aqualight has found a wide range of applications in mining industries around the world. In addition to cavity- filling, Aqualight has been used for ventilation stoppings, fire stoppings and emergency fire control, backfilling between arches and the roof and ribs, and backfilling of old workings. Since its recent introduction into the United States. Aqualight has been used by MICON SER- VICES, INC. to fill several roof fall cavities along headgate entries. In all cases, the cavities were contained and the longwall moved through without problems. Roof Pall cavities along main haulage entries and at shaft/slope bottoms have been successfully filled. MICON has also installed Aqualight as backfill material around arches. A current major project is the installation of trial ventilation seals using Aqualight as an alternative to traditional block and mortar construction. Pending MSHA approval, MICON anticipates the use of Aqualight in the construction of both ventilation seals and stoppings. In addition to new construction, Aqualight can be employed to repair stoppings damaged by roof convergence and floor heave. In labor savings alone, this is very attractive for remote stopping repair. Among the many other uses of Aqualight is the backfilling of old auger holes, which will support the highwall and allow access to coal re- serves which are presently sterilized.

Jan 1, 1986

By S. Kemball-Cook, D. Heinze, A. Kornberg, M. Harmon

Climate change presents risks to mine infrastructure, operations and long-term obligations to protect environmental conditions. Management strategies and design of infrastructure and containment systems based on past or current climate conditions may be inadequate in the future if changes in climate are not taken into account in planning for mine operations, decommissioning, closure and post-closure. Data-driven assessments using climate model projections of the future can be used to quantify: • Changes in site-specific risks to mine structures, access, containment facilities, operations and staff safety. • Changes in vegetation and water balance/chemistry, and potential for acid mine drainage, erosion and design failure. Climate- and weather-related risks are a serious threat to the mining industry, but risk transfer solutions can alleviate these vulnerabilities. Mining companies can protect themselves through bespoke solutions which provide operators, investors and buyers with protection against weather-related disruptions to operations by hedging to smooth revenues. Using risk transfer structures to mitigate climate risks is a mechanism that is available to all types of mining operations world-wide. In this paper, we describe methods for evaluating site-specific climate change impacts and developing risk transfer solutions to mitigate their effects. EVALUATING MINE RISKS FROM CLIMATE CHANGE The best available tool for understanding potential future changes to the earth’s climate system are global climate models (GCMs) (IPCC, 2014). GCMs are computer simulations of the climate system which include the atmosphere, ocean, land surface, cryosphere and biosphere. Because of the computational demands of running a global model for many decades, the spatial resolutions of the GCM grids are necessarily coarse, typically on the order of 100-300 km. GCM data are therefore suitable for evaluating future physical risks on global or continental scales, but may not be appropriate for evaluating location-specific risks (e.g. Kotamarthi et al., 2016). For site-specific, quantitative physical risk assessment, GCM projection data are “downscaled” or adapted for use at the local level using statistical techniques together with observed data (statistical downscaling) or using high-resolution regional climate models (RCMs) that focus on a single geographic region and have spatial resolutions of 10-50 km (dynamical downscaling). Downscaling bridges the gap between the GCM scale and regional/local scale. Through the downscaling process, new information is added to the GCM output from observations and/or RCMs, resulting in patterns for weather variables that are more consistent with local terrain and weather influences. Downscaled climate change projections for the mine site are selected considering mine location and geography, the availability of local observations, and the performance of the downscaling method and global/regional models used to develop the projection in simulating the variable under study. Where possible, we use projections from an ensemble of global and regional model runs spanning a range of future greenhouse gas (GHG) scenarios.

Jan 1, 2019

By Delbert L. Keenon

The principal concepts of computer control and automation have been successfully applied in industries world-wide, The enthusiasm generated by the proponents of computer control, and the apparent mystery enveloping the techniques of computer control, have caused attention to be focused on this infant industry from all quarters. Consequently, the motivation to "computerize" may be the hope that computers will solve all economic problems. The truth remains that not only have there been monumental successes, but there have been some colossal failures. This paper will attempt to outline a generalized guide to computer control and present methods for avoiding some of the major pitfalls. Since the investment required for computer control systems has been drastically reduced in the past year, small operations will likely find that computerized process control is attractive in areas where it has never been considered before, The discussion presented here is intentionally non-technical and directed towards those who may soon find they have a possible application for a control computer. The primary purpose of computer control is to reduce expenditure and increase profits by improving the quality of product, increasing the efficiency of operation, reducing the materials and man hours required or a combination of these. Success or failure to reach the desired goal depends, to a large degree, on a well-planned approach. This includes recognizing a possible computer application, properly defining the job which is to be accomplished, evaluating computer systems, selecting a capable manufacturer, and following through with sound systems engineering and programming.

Jan 1, 1965

By James M. Barker, George S. Austin

Stone, one of the oldest building materials, today remains a well-established material throughout the construction industry. The use of natural stone is much less prevalent now than in the past. It is still widely considered to be the most aesthetically pleasing, prestigious, and durable building material. New and re-opened quarries are coming onstream to meet increased demand related to new building technology and increased residential use of stone. CLASSIFICATION No classification can completely eliminate overlap between dimension stone, aggregate, and decorative stone because most stone is multi-purpose. Many used for decorative purposes are not produced specifically for that end use. Rock otherwise considered waste in dimension stone or aggregate quarries can be decorative stone coproducts (Fig. 1). Many uses require a compromise between decorative and structural qualities (Bowles, 1992, written commu¬nication). Shipley (1945) used decorative stone interchangeably with or¬namental stone. Gary et al. (1972) defined decorative stone as that used for architectural decoration, such as mantels, columns, and store fronts, but added that it is sometimes set with silver or gold in jewelry as curio stones. Bates and Jackson (1987) also restricted decorative stone to that used for architectural decoration. Meanings of otherwise identical terms used in the stone industry differ be¬tween geologists, engineers, and quarriers. They often carry a much broader meaning for quarriers and engineers compared to their very specific use by geologists (Makens et al., 1972). Decorative stone, including ornamental stone, is more broadly defined by geologists as any stone used primarily for its color, texture, and general appearance. It is not used primarily for its strength or durability, such as construction stone, or in specific sizes, such as dimension stone. The decorative stone industry uses a much wider range of stone types compared to stone that is dimensioned. Decorative stone usually serves some structural pur¬pose, but is not load-bearing to any great extent. Weak or costly stones serve in decorative, not structural, applications. STATISTICS AND END USES Decorative and dimension stone data are difficult to separate because the US Bureau of Mines keeps statistics only on dimension stone and crushed stone. The value of domestic dimension stone production in 1990, which includes some decorative stone, was about $210 million compared to imports of about $524 million and exports of about $35 million. Production was 1 080 t of which at least one-third was for decorative uses (Taylor, 1992). The principal uses are rough blocks in building construction (23%) and monu¬ments (18%); the remainder is used as ashlar (18%), curbing (12%), and miscellaneous (29%). Major rock types are granite (50%), limestone (30%), sandstone (10%), slate (3%), marble (2%), and other (5%) (Harben, 1990). Crushed stone valued at $5.6 billion was produced in the United States in 1990 by 1700 companies operating 3400 active quarries in 48 states (Tepordei, 1991). About 52% is used in con¬struction, 9% in cement and lime manufacturing, 2% in agricul¬ture, 2% in industrial uses, and 35% for unspecified uses including decorative aggregate. Limestone and dolomite comprise about 71%, granite 14%, and traprock 8% of the stone crushed in the United States. The remaining 7% are, in descending quantity, sandstone, quartzite, miscellaneous rock, marble, shell, calcareous marl, volcanic cinder and scoria, and slate. The basic types of decorative stone are: rough stone, aggregate, cut or dressed stone, and manmade stone [(Table 1)]. Rough Stone Rough stone is used as it is found in nature with very limited processing such as minor hand shaping, edge fitting, and size or quality sorting (Perath, 1992, written communication). This stone type is often marketed locally in relatively small tonnages and includes fieldstone and flagstone. The primary end uses of rough stone are landscaping, edging, paving, or large individual stone landscape or interior accents [(Fig. 2)]. Fieldstone: Fieldstone is picked up or pried out of the ground (gleaned) without extensive quarrying and includes garden or large landscaping boulders (Austin et al., 1990, Hansen, 1969). Boulders and cobbles may be split or roughly trimmed for use in rubble walls and veneers, both interior and exterior. Popular fieldstone rock types include sandstone, basalt, limestone, gneiss, schist, quartzite, and granite, but many others are suitable. Much fieldstone is col¬lected by individuals or small companies because the industry is labor intensive and markets are small. The stone may be sold locally in small quantities from the back of vehicles (Austin et al., 1990). Fieldstone includes many rock types, sizes, and shapes with the only common denominator that it must be set by hand and be durable (Power, 1992, written communication). Moss Rock. Moss rock is fieldstone partially covered by algae, mosses, lichens, and fungi that give the rock an aged and variegated patina (Austin et al., 1990). The plants are supported by moisture and nutrients in the stone. Moss rock is used for landscaping, walls, and fireplaces. Although almost any durable rock can be a moss rock, most are slabby or rounded sandstone and limestone (Fig. 3). Flagstone: Flagstone or flagging consist of thin irregular slabs used for paving, walkways, and wall veneers. Random-shaped flagging is produced widely in the United States. Suitable stone

Jan 1, 1994

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003

By S. Saeed, N. Coulson, P. F. Stewart

"The Mine, Health and Safety Act No. 29 of 1996, as amended, embodies worker self-regulation to advance health and safety in the workplace. An important provision for this is the Right to Refuse Dangerous Work (RRDW). This paper explores worker perspectives about the implementation of RRDW on South African mines against a backdrop of revised guidance in the sector: ‘Guideline for a Mandatory Code of Practice on the Right to Refuse Dangerous Work And Leave Dangerous Working Places’, gazetted in February 2016 by the Department of Mineral Resources (DMR). A mixed methods study conducted at mines (n = 14) included a survey of workers (n = 293), focus groups (n = 6) and in-depth interviews (n = 16). Workers reported a high level of awareness, a positive attitude, and experience of the formal RRDW. However constraints to the formal RRDW meant that informal worker resistance to dangerous work was commonplace. Evidence of informal non-confrontational consultation, cooperation, and collaboration in the event of a dangerous workplace also emerged between workers, and supervisors. The research underscores the importance of the RRDW and worker health and safety representatives to mine health and safety. The revised guidance addresses RRDW implementation gaps, but of concern is the potential partiality towards management interests. IntroductionEnsuring that mineworkers act on their duties and responsibilities for health and safety remains a concern across the globe. Article 13 of the International Labour Organization (ILO) Convention Safety and Health in Mines (176 of 1995) entrenched the Right to Refuse Dangerous Work (RRDW) as an important mechanism through which workers act in the best interests of their own occupational health and safety (OHS) and is considered a cornerstone of worker self-regulation (ILO, 1995). Countries ratifying Convention 176 are under obligation to make this right available to workers through OHS legislation that frames the circumstances, procedure, and protection of workers from discrimination in the event of a formal work refusal. The Convention has been ratified by 31 countries, with South Africa becoming a signatory in June 2000 (ILO, 2000). Worldwide studies show that workers use this right with caution (Hilgert, 2013) and cases associated with work refusal are rarely presented in court (Gunningham, 2007; Cooper, 2013). Rather, in cases of formal notification of a work refusal, issues arising out of this are addressed either in the immediate workplace or through the site OHS system and/or at industrial tribunals or similar mechanisms (Harcourt and Harcourt, 2000)."

Jan 1, 2018

IN THE past, we have, perhaps, been somewhat careless in our furnace practice, in the use of high-grade material, lowering the production costs through demanding high-grade ores, increasing the size of units, and eliminating heat losses by collecting and returning unused heat to our furnaces. Further economies would seem to be possible through keeping out of the furnace those materials that appear to serve no useful purpose and carry with them heat that should be used in reduction operations. In the manufacture of pig iron, about three tons of inert nitrogen pass through the furnace for each ton of iron produced. This nitrogen serves no useful purpose in the chemical actions involved, but when discharged into the atmosphere it carries away a considerable quantity of heat. Can not this loss be eliminated, at least in part, through the use of more oxygen in the blast? Many metallurgical chemists, during the past 20 years, have stated that they thought it can and have urged that the plan be tried. Others have expressed doubt, not being able to visualize how more oxygen could be used in present practice; they have regarded it as impracticable, without trying to conceive of an entirely new practice based on a new reagent. That more experimental work has not been done is due to the fact that no cheap oxygen has been available, but the committee believes that there is strong reason to expect that, should a demand exist, 99 per cent. oxygen may be made at a cost not to exceed $3 per ton. The theoretical studies of the committee have indicated such marked economy by using oxygenated air in various operations that its members strongly recommend experimental work to verify the anticipated economies. The committee has developed plans for experimentally determining the effects of oxygen-enriched air on the operation of an iron, blast furnace. A furnace with a height of 30 ft. has been built and it is recommended that the plans be put in, effect as the first step in the research.

Jan 11, 1924

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX&apos;S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger&apos;s strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By W. H. Ode

In 1949 the Coal Committee of the Economic Commission for Europe, Geneva, Switzerland, established a Classification Working Party, to develop an international system for classifying coal. This project was necessitated by the increased trade in coal among various nations following World War II. Although national classification systems existed, they had been developed to cover the characteristics of domestic coals without reference to coals of other countries. Different terms for describing similar or identical coals in each nation caused confusion in evaluating coals shipped in international trade. Experts from Austria, Belgium, Bulgaria, Czechoslovakia, Denmark, the Federal Republic of Germany, France, Greece, Hungary, Italy, the Netherlands, Poland, Sweden, the Union of Soviet Socialist Republics, East Germany, the United Kingdom, the United States of America, and Yugoslavia participated in various stages of the classification work. Walter A. Selvig was appointed by the Bureau of Mines as the technical expert to represent the United States because of his experience in developing and standardizing methods of analyzing and classifying American coals. He served on the Classification Working Party until his retirement from the Bureau of Mines early in 1956. Extensive laboratory work was done in connection with the classification studies at the Pittsburgh Experiment Station of the Bureau of Mines.

Jan 1, 1958

By Henry Hu

In high pressure die casting processes, proper control of temperature die yields a high casting production rate and superior quality components, Die temperature is usually influenced by various die design and process parameters such as size and location of intemal water cooling lines, flow rates of cooling lines, and pouring temperature of molten metal. Among them, the cooling water flow rate plays a major role in controlling thermal pattern of the die_ In order to develop an effective control strategy, data of local die temperature must be collected and analyzed, In this study, a PC-based data acquisition and control system (DACS) for die temperature control has been designed, and established, The developed DACS has three input channels for temperature signals and one input channel for water flow rate signals, as well as one output channel for a water pump, and is capable of displaying data in both curve format and value format. Implementation of the DACS in a laboratory setup has also been attempted, It should be pointed out that more advanced control mechanisms can be potentially integrated into this system in future,

Jan 1, 2003