Search Documents

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By A. I. Johnson

The pegmatites of the Black Hills of South Dakota are the coarse-grained differentiates of the Harney Peak Granite. The Harney Peak Granite was intruded into the Pre-cambrian schist and quartzites and resulted in the Black Hills uplift. In the outer adzes of the granite intrusion occur the pegmatites. In the zoned pegmatites, representing the most highly differentiated portions of the parent magma, occur most of the minerals produced from pegmatites. These are of economic importance and they are the subject of this paper. The various mineral products will be taken up separately.

Jan 1, 1978

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

By J. Weinberg

This Bureau of Mines report presents data on the changes in the use of steel in motor vehicles over the past 35 yr. Sources of supply of steel for the automotive sector have shifted from almost all domestic in the 1950's to about 50% domestic and 50% foreign in the 1980's. Downsizing, design changes, and substitution of lighter weight materials to achieve energy efficiency also contributed to the market loss of the domestic steel industry. Although plastics and aluminum have displaced some steel in motor vehicles over the years, heavy low-carbon steel is now being replaced most rapidly by lightweight high-strength steel. If the percent of domestic steel used in motor vehicles had not declined since 1950, domestic industry would have supplied 9.3 million more short tons of steel than it supplied in 1985. Downsizing and design changes accounted for 43% of the loss; steel imports, 32%; and substitution of plastics and aluminum, 25%. In 1985, the total value of market share lost by U.S. steel producers was $5.1 billion, of which $1.6 billion was lost to foreign steel producers and automobile manufacturers. Through aggressive marketing and increased efficiency, however, the domestic steel industry may be able to recapture some lost markets, as applications for high-strength steels expand, and as foreign-owned automotive plants in the United States provide fresh sales opportunities.

Jan 1, 1988

By A R. Cruden, M S. Egglseder

The formation of banded iron formation (BIF)-hosted high-grade iron ore deposits in the Hamersley Province, Australia has been debated for decades. Although a structural control on their formation is widely accepted, only the roles of large-scale structures (ie faults and folds) formed by brittle and ductile deformation have been considered to date. However, the deformation of multilayered sequences in the Hamersley Province (ie the Mount Bruce Supergroup), with their contrasting rheological behaviours, creates challenges for understanding the complex structural framework at regional to deposit scales, including the significance for mineralisation and orebody location.Our approach to understanding these complex relationships is based on an established principle of structural geology, which is to extrapolate microscale structures to deposit-scale structures and vice versa, supported by state-of-the-art 3D modelling techniques. Complexly deformed hand samples associated with the Mount Tom Price iron ore deposit (Hamersley Province, operated by Rio Tinto Ltd) have been analysed and visualised with 3D explicit (Move™, Midland Valley Ltd) and implicit modelling software packages (Leapfrog™, AranzGeo Ltd) and supported by microstructural investigations (optical and X-ray microscopy) and fieldwork.Our study shows that the deformation of BIFs in the central Hamersley Province is controlled by microscale chemical processes (ie dissolution precipitation creep) due to rheological differences between iron oxide and chert layers, contrasting fluid flow properties and layer thickness variations. These processes account for the removal of vast amounts of silica, its transportation by diffusion in the presence of a fluid and reprecipitation at low-pressure sites. Consequently, this structural framework was used by different upgrading fluids to form iron orebodies.CITATION:Egglseder, M S and Cruden, A R, 2015. Evolution of a structural framework for high-grade iron ore deposits, in Proceedings Iron Ore 2015, pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D A. Vogel

"Sampling may be mandatory for safety or environmental reasons. It may be because the value of a sale needs to be determined or to provide important data for investments. Whatever the reason, an incorrect sample will come at a risk. Only the person that relies on sampling data can imagine what the potential cost of such risk is.Sampling itself has a cost too; the direct cost of a quality control department and indirect cost for interrupting a process, such as stopping a conveyor belt during loading. If all material is the same then only one small sample is enough. But if all the material is different, then a very large sample must be tested; in the conveyor belt scenario it must be stopped very frequently and the associated cost will be high.A good sampling plan finds the proper balance between risk and cost. A good sample must be small enough to handle yet large enough to be representative for what information is required. All good samples have three things in common: there was proper access to the material the sampling tool allowed equal probability of particles being selected nothing was disregarded, everything was included.This too is the core of Gy’s ideal sampling scenario, where all particles have the same probability of being selected and included in the sample. There is risk of bias when part of a lot is excluded from the sample. Extra care is needed when sampling particularly heterogeneous, segregated or layered materials. The sampling tool should never systematically leave out a portion; it shall not push aside large or hard particles. Wet samples shall not stick to the sampling tool. This extends to sample preparation too when reducing particle size and dividing the sample in the process.CITATION:Vogel, D A, 2017. Access, select, include – a review of the commercial sampling of traded bulk commodities in the context of Gy’s Theory of Sampling, in Proceedings Eighth World Conference on Sampling and Blending, pp 367–378 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By R. O. Suzuki, S. Natsui, R. Nashimoto, T. Kumagai, T. Kikuchi, H. Takai

A newly developed computational fluid dynamics model based on a multi-phase particle simulation is presented for predicting the entrainment behavior of liquid metal into slag due to rising single bubble. By comparing results calculated using this model against experimental data, it was found that the transient behavior of bubbles and the two immiscible liquids can be accurately estimated by this method. The rupturing of the thin water film surrounding the bubble was less reliably predicted, but this 3-dimensional unsteady numerical model still nevertheless provides valuable new information for directly predicting the change in the liquid-liquid interface over time. This model predicted the Young-Laplace pressure, and the interface shape was simulated with volume conservation using this model as opposed to the conventional particle method. This simulation model can calculate both of dispersed phase and continuous phase seamlessly.

Jan 1, 2015

By Harry Deitzer

Within the industrial marketplace barium sulfate has an established role as a filler or extender pigment for use in a wide array of applications. The focus of this paper is to outline a number of these applications and in each one characterizes those features of barium sulfate which provide value. Following this is a discussion of the process techniques which have been used to develop value from a selected class of barite ores found in southern Missouri. It is appropriate to define some terms which may help in clarifying some concepts as presented. Use of the term barium sulfate refers broadly to the chemical compound BaSO4 Barite will generally refer to the naturally occurring barium sulfate ores and their properties. Barytes, whether bleached or not, will refer to barite ore made suitable for industrial applications.

Jan 1, 1993

By Thomas M. Barczak

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By James Pennington

[The Mining and Metallurgical Divisions of the Bureau of Mines, Region V, conducted an investigation in 1950-51 of the iron sulfide deposits in Aitkin and Carlton Counties, Minn. Twelve diamond-core-drill holes, aggregating 2,347 feet, were drilled in secs. 14 and 15, T. 46 N., R. 25 W., Aitkin County, to increase reserves of iron sulfides known to exist 2 miles southwest in secs. 28 and 29, T. 46 N., R. 25 W. Three diamond-core-drill hobs, totaling 561 feet, were drilled in Canton County, sec. 7, T. 46 N., R. 2 0 W., to check reports of the presence of a large sulfide deposit in that area. Mineral-dressing tests were made on cores from 10 holes drilled in Aitkin County. These included core from hole 21 drilled in sec. 28 and submitted by the Glen Development Co.]

Jan 1, 1953

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

By B. E. Davis

The Bureau of Mines conducted tests on samples of two Florida phosphate slimes t6 devise a technique to recover phosphate currently dis-carded because of its fine size. A flotation technique was devised to recover the phosphate contained in two fractions of each slime: the plus 37um fraction and the plus 20-um fraction. The technique involved conditioning the flotation feed with sodium silicate and a fatty acid-fuel oil emulsion, floating a rougher phosphate concentrate, and cleaning the concentrate in two cleaner stages with sodium silicate added to each for gangue depression. Concentrates containing 21.0 to 32.3 pct P20S were produced with recoveries of 68.1 to 84.2 pct of the P20S con-tained in the flotation feed.

Jan 1, 1987

By A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach- solvent extraction process devised to cleanly separate the metal values, and produce acid sulphate liquors containing the metals. It is shown that 86 percent of the nickel and 95 percent of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible.

Jan 1, 1964

By N. B. Aughenbaugh

This report summarizes the results of an investigation into the causes of coal mine roof instability caused by the environmental characteristics of the air ventilated through a mine. The field studies, which were mostly in the Illinois Coal Basin, concentrated on collecting data of surface weather conditions, mine air characteristics (relative humidity and temperature), roof material types, roof movements, and characteristics of roof deterioration. The field studies revealed seasonal changes in weather are reflected in the mine air. The intake air undergoes rapid tempering along its course as it interacts with the ambient mine conditions. There are seasonal moisture interchanges between the mine rock and air, and a mine will lose more water than it gains on a yearly basis. The field studies also established that when the roof rock is shaley, seasonal changes in the humidity will cause roof deterioration because of the detrimental action of moisture on the shale. Roof falls were inventoried and classified by geometry. In the laboratory investigations, physical tests proved unreliable for evaluating shales for roof stability. The Franklin slake test lacks the sensitivity needed to differentiate shale durability for roof stability. A relative humidity test that reveals the sensitivity of a shaley rock to moisture change was devised. Environemntal chamber studies showed that neither temperature nor barometric pressure have a direct influence on shale durability. Photoelastic studies showed that the rate and depth of moisture absorption into a shale is controlled by bedding planes, fractures, and holes interrupting the exposed surface.

Jan 1, 1976

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

With the burgeoning opportunities for new gold mines to be developed the opportunity now exists for a reassessment of the optimal processing path for these gold ores. Projects have traditionally followed the path of whole ore cyanidation with either Carbon In Pulp (CIP), Carbon In Leach (CIL) or Merrill Crowe. The challenge ahead is whether these traditional processing methods are the best option for stakeholders, or to go beyond CIP and use a combination of currently available technologies that can be used to provide gold recovery at a significantly reduced capital cost and minimal deleterious impact on the environment. Either stand alone or combinations of gravity concentration and flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. Treatment of a gravity/flotation concentrate by intensive cyanidation may be processed by the InLine Leach Reactor (ILR) developed by Gekko Systems of Australia. The advantages of the technology combining gravity/flotation followed by intensive cyanidation are significantly reduced capital costs; improved safety due to reduced cyanide inventories; the majority of tailings un-contaminated by cyanide; less energy required due to an opportunity for an increase in grind size û reducing green house gas emissions; detoxification of concentrate tailings can minimise tailings disposal and containment requirements.

Jan 1, 2004

By Joel B. Dellaria, Justin R. Lewis

"No. 9 Walton is a new high-rise condominium building located in the Gold Coast area of Chicago. The adjacent building, Walton on the Park, featured 4 levels of below grade parking and utilized a secant pile wall with integral drilled shafts to support the exterior columns. The earth retention system (ERS) for No. 9 Walton also employed a secant pile wall in combination with drilled shafts. The excavation into the soft Chicago clays varied in depth from 9.75 m to 12.5 m (32 feet to 41 feet) below grade. The temporary excavation support used internal braces from the new secant piles to the existing foundation system of Walton on the Park to provide earth retention. Engineering teams for both projects worked together to design the bracing scheme and connections to ensure that the new excavation and internal bracing would not overstress any elements of the existing structure. Further complicating the project, immediately to the west of the project was a historic church founded on shallow spread footings which required underpinning to minimize movements.The project involved three different building owners, small values for acceptable wall movement, an extensive monitoring program and the challenges of merging two earth retention systems. The subsurface conditions at the site, the adjacent structures, the excavation, and the performance are described. A summary of the design methods and the expected movements of the ERS are discussed, and the performance monitoring system is described. Overall, the ERS performed better than expected with less than 1 inch of measured lateral wall movement during and after the excavation was completed. Measured performance of the ERS is compared to the predicted performance and to the performance requirements for the project.INTRODUCTIONNo. 9 Walton is a new high-rise condominium building in Chicago located in the Gold Coast. The building has 3 levels of below grade parking and 36 levels of living space above grade. Developers originally slated the project to be Phase 2 of the Walton on the Park development built in the mid 2000’s, using portions of the existing foundation system for development of the new structure. However, the housing market crash in 2007 prompted cancellation of Phase 2 of the Walton on the Park development. The property sat undeveloped until 2015 when design and construction for No. 9 Walton began under a new development and design team. The project team completed foundation excavation and below grade structures in 2016 with the first units of the building turned over to new homeowners in 2017.The structural design for No. 9 Walton consisted of reinforced concrete columns and slabs, supported laterally by a heavily reinforced concrete central core. Drilled shafts to rock supported the interior columns and core with the exterior columns and foundations integrally included in the earth retention system. The structure had a below-grade footprint of approximately 1,490 m2 (16,000 ft2). The general excavation extended 9.75 m to 12.5 m (32 feet to 41 feet) below street level with the deepest portions at the central building core mat foundation."

Jan 1, 2017