Search Documents

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By J. A. Dlas Lima

Alunorte is a metallurgical-grade alumina refinery located in northern Brazil. This plant which was designed to produce 1.1 million mtpy of calcined alumina, started operation in July 1995. A process information system was installed before refinery start-up. It has been a main factor in process improvements, which resulted in an increase in production from 1.1 to 1.5 million mtpy. This system has been particularly useful for analyzing data and allowing retrieval of data by process engineers. This paper describes how a quality monitoring system to evaluate all aspects and stages of production, as well as alumina silo level and blending percentage, was developed. This system was designed to give support to ISO 9002 certification, which happened in December 1998. The quality monitoring system was developed using Microsoft Excel 7.0 and makes extensive use of VBA macro. The primary users of the system are shift foremen, managers and engineers, who use it to track the process and avoid variations in alumina quality.

Jan 1, 2000

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda&apos;s interest in the techniques stems from long experience with vat and heap leaching, &apos;dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By Alireza Ayoubian, Richard Finno

The network of freight tunnels in Chicago consists of about 62 miles of horseshoeshaped tunnels constructed typically less than 50 feet below ground surface. These tunnels serve as repositories of much infrastructure and should remain serviceable. The tunnels are often impacted by adjacent excavations and the question arises as to the existing state of stress in the final liner. This paper discusses construction of these tunnels and presents the results of finite element analyses which were used to obtain ranges for axial forces and bending moments that have developed in the final liner of the freight tunnels since their construction.

Jun 13, 2023

By M. Laliberte

Gold mine effluents are often characterized by a high concentration of copper, ammonia and cyanide derivatives (mostly cyanates and thiocyanates). While non-acutely toxic to birds, this water can be acutely toxic to fishes and invertebrates. In many jurisdictions, the effluent requires further treatment in order to pass a mandatory requirement to be non-lethal to species like the rainbow trout (Oncorhynchus mykiss) or Daphnia magna. Using actual mine water, it has been demonstrated that aerated moving bed biofilm reactors will biodegrade the ammonia, cyanides, cyanates and thiocyanates, thereby removing the toxicity associated with these components. By removing copper by precipitation the water can be made to pass acute toxicity tests. Tests have demonstrated that the process is stable between 4 and 25 C, with no significant changes in the treated water composition. Once the biomass is acclimatized, the process is resistant to upsets and requires very little inputs except for phosphorus and air. Furthermore, it has been demonstrated that an anoxic reactor can be added downstream of the aerated reactors to remove nitrates if required.

Feb 23, 2014

By Scott Honan, Tassos Grammatikopoulos, Mike Johnson, Kelton Smith, Niels Verbaan, Ernesto Bourricaudy, Eric Larochelle, Rick Sixberry

"NioCorp is developing the niobium/scandium/titanium Elk Creek carbonatite resource deposit. The carbonatite phase contains significant niobium (0.71% Nb2O5), titanium (2.68% TiO2) and scandium (72 g/t) and is composed predominantly of calcite, dolomite and ankerite. Niobium is mostly (80%) contained in the pyrochlore and the balance in various Fe-Nb-Ti oxides, which also host most of the titanium. Scandium is distributed homogeneously throughout the ore mineral assemblage. The process flowsheet recovers separate niobium, titanium and scandium products. Scandium is extracted from whole ore hydrochloric acid leach solutions through solvent extraction, and is further refined through a re-leach and precipitation process. Scandium leach residues are treated with sulphuric acid to recover separate niobium and titanium precipitates. Both hydrochloric acid and sulphuric acid reagents are recycled within the flowsheet. This paper will discuss key bench and pilot test results (focusing on the scandium flowsheet) and will present a conceptual flowsheet developed by the project team for NioCorp at SGS Minerals.INTRODUCTION NioCorp is developing North America's only niobium/scandium/titanium project. The Elk Creek project is located near Elk Creek, Nebraska, and is the highest grade niobium project in North America and the largest prospective producer of scandium in the world. These elements are unique and valuable superalloy materials that are strategic and critical to many industries and national defense technologies. The project includes the Elk Creek Carbonatite (the Carbonatite) that intruded older Precambrian granitic and low to medium grade metamorphic basement rocks. Both the carbonatite and Precambrian rocks are interpreted to be unconformably overlain by approximately 200 meters (m) of Paleozoic marine sedimentary rocks of Pennsylvanian age. As a result of this thick cover, there is no surface outcrop within the Project area of the carbonatite, which was identified and targeted through magnetic surveys and confirmed through subsequent drilling. The available magnetic data indicate dominant northeast, west-northwest striking lineaments, and secondary northwest and north oriented features that mimic the position of regional faults parallel and/or perpendicular to the Nemaha Uplift."

Jan 1, 2017

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By I. AITKENS

It is a common misconception that all yellow stones are topazes and that all topazes are yellow; but neither statement is true. The real topaz is a rather rare mineral, and a large number of yellow stones that masquerade as topaz are nothing more than yellow quartz, known as citrine, but almost universally called topaz. The true topaz is often called "Brazilian" topaz by the jeweler to distinguish it from yellow quartz; nevertheless, both terms are freely applied in trade to other yellow stones. Topaz is considered the most popular yellow stone for jewelry and is often used as the principal stone in brooches or pendants, especially in old-fashioned ornaments. However, many other species yield pretty yellow stones, some of which are far more numerous and less costly than the topaz.

Sep 1, 1931

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By P. H. Griffin

WHEN a subject, such as the manufacture and service of chilled car wheels, as has been fruitlessly discussed for ten or fifteen years, it is difficult to revive interest and action by the mere repetition of statements and arguments that have been made before. And when a situation involves serious responsibilities for conditions that have grown up under circumstances beyond the control of any particular individuals or authority, it is even more difficult to deal with. But there is one phase of every subject that need not involve these particular points if presented in a, proper manner; and that is, " the future state." I will try to present the subject of this communication from the latter standpoint and with the hope that all of those interested will feel disposed to give the matter attention from the basis that it is a, vitally important one to all that travel on railroads, whether as employees or officials, or as dependent on those in charge of the operation, or in the matter of materials and equipment used. The conditions of chilled wheel service have been changed so radically in the past ten or fifteen years by the use of freight cars of 40 and 50 tons capacity, that it is fair to say in the interest of all concerned in the use and in the manufacture of such wheels, that the increased strains and loads have been quite sufficient to account for much of the service results that have transpired. That proper provision was not made for increased possibilities of strength and wear, in fact that previous factors of the kind were allowed to deteriorate, is no proof that such wheels cannot be made equal to heavy service conditions as shown in the data given herein.

Jan 10, 1913

By A. A. Compoli

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No.3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No.3 Coalbed.

Jan 1, 1995

By Charles D. Haynes

Outside air for ventilating coal mines in Alabama varies considerably in both temperature and moisture content during the year. Alternate condensation and evaporation of the moisture on mine roofs may result in stresses detrimental to the strength of mine roof. It is well known that the clays in shales absorb moisture, and many investigations have noted the weakening of shales by absorption of moisture. Parker (1970) concluded that there is an annual cycle of rock deterioration in mine roof rock caused by the annual temperature-humidity cycle at the surface. He further noted that moisture reduces the strength of dry rock by one-half, that moisture added to dry rock can cause failure in compression, and that drying of wet rock causes tensile stress buildups by shrinkage. His recommendations for alleviating the moisture-temperature problem was to seal the rock in critical areas and to control ventilation so that air temperature will be lower than rock temperature. The latter recommendation will avoid condensation on the rock surfaces. Hartmann and Greenwald (1941) published the results of a very comprehensive experimental project to determine the effect of temperature and humidity changes on the behavior of mine roof. Their general conclusions included statements that roof rocks were very sensitive to moisture changes, but had low coefficients of thermal expansion. The coefficients were twice in the direction normal to the bedding plane as compared to the parallel

Jan 1, 1975

By Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Cold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 9 million tons of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 1.0 million tons per year. Careful evaluation of the combined results of successive sampling projects has established the pit plan, mineable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1984

By Joseph Daniels

(San Francisco Meeting, October, 1911.) I. THE FRITZ ENGINEERING LABORATORY. TEE Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. . The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem, and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight, 84 ft. long and 9 ft. wide, in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section, containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Feb 1, 1912

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Paul O. Knorr

The Bureau of Ocean Energy Management (BOEM), a bureau within the U.S. Department of the Interior, has responsibility over both energy and non-energy mineral development on the United States Outer Continental Shelf (OCS) under the OCS Lands Act (“OCSLA”). BOEM’s Marine Minerals Program (MMP) manages federal offshore mineral deposits through non-competitive, negotiated agreements for sand and gravel (“sand”) used in coastal restoration efforts and the competitive leasing of critical and hard economic minerals (“critical minerals”). As the steward of OCS critical minerals, BOEM MMP is responsible for understanding where critical minerals are located, identifying and understanding their environments, managing activities that affect these resources, and implementing pertinent federal policies. Fulfilling these responsibilities involves the collection and analysis of environmental, geological, and geophysical data; supporting the science needed to understand the impacts of resourcerelated authorized activities on the biological, physical, and sociocultural environments; encouraging emerging technologies that can reduce the environmental impact of activities; and communicating with stakeholders to foster an understanding of existing federal regulations and potential needs to revise the legal framework. Four U.S. federal rules in the Code of Federal Regulations (CFR) currently inform MMP’s procedures: 30 CFR 580 (prospecting for minerals), 30 CFR 581 (leasing of minerals), 30 CFR 582 (operations in the OCS related to minerals), and 30 CFR 583 (negotiated noncompetitive agreements for sand). Other federal laws and regulations are also pertinent, particularly those supporting the National Environmental Policy Act, Endangered Species Act, National Historic Preservation Act, Marine Mammal Protection Act, Coastal Zone Management Act, Clean Air Act, Federal Water Pollution Control Act, and Magnuson Stevens Fishery Conservation and Management Act.

Feb 22, 2026