Search Documents

By Frank H. Madison

The percentage depletion deduction on Federal Income Tax Returns under the provisions of the 1939 Internal Revenue Code and of Sections 611 to Section 615, inclusive, of the revenue act of 1954, have created innumerable administrative difficulties, and a new interpretation of "gross income from the property" in that the Courts have expanded the ideas of what constitutes "gross income from the property" to a degree unheard of and unthought of prior to the enactment of these two codes. Originally, under the Revenue Acts of 1917, 1918, and 1920 depletion was allowable, based upon mine valuations as of March 1, 1913; if the mine was owned prior to March 1, 1913; upon cost, as of the date of acquisition if purchased subsequent to March 1, 1913; and upon a "discovery" basis if the mine was discovered after March 1, 1913, The "jab" for mine valuations as of March 1, 1913 and for discovery valuations and depletion was not as bad as it has been made out to be. Thousands of valuations and estimates of reserves were made and agreed upon between taxpayers and Internal Revenue Service engineers and as the years went on the answers have been found to be "reasonable." However, human nature being what it is each case was a battle of wits - of a sort - and many resulted in severe differences of opinion and litigation. As tax rates increased the situation was not bettered. I could talk for several hours on this phase of depletion but it is all past now andwould not give any real service or better understanding of the matter.

Jan 1, 1958

By R. R. Klimpel

The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and the development of coal gasification/liquefaction processes which require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology, Klimpel (1982, 1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variations in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: (1) slowing down of breakage rates, (2) the occasional acceleration of breakage of some sizes, and (3) conditions where chemical additives will increase rates of breakage.

Jan 1, 1990

By Jorge Madias

O trabalho está baseado na análise de dados de perto de 200 fornos elétricos a arco de diferente design: convencional, de corrente contínua, de carcaças gémeas, com preaquecimento de sucata no transportador ou em shaft, etc. Incluem-se fornos que processam principalmente sucata, e fornos com carregamento parcial de gusa sólido ou líquido, ferro briquetado a quente (HBI) ou ferro esponja (DRI) a frio ou a quente. São avaliados os consumos de energia elétrica, oxigênio, gás natural e materiais carbonosos; os tempos entre vazamentos, com forno ligado e com forno desligado, assim como a produtividade horária. Com os dados obtidos, se analisa a influência dos metálicos (e seu estado térmico ao momento do carregamento), e o design do forno, sobre os consumos específicos mencionados e a produtividade.

Oct 30, 2017

The paper point out the way whereby the Canadian gobernment regulates and motivates mineral development. In this sense, its important the role of Gobernment policy in the development of the industry to its a stage. The progress of industry is due to a favorauble political climate which created an atmosphere of trust that has atracted foreing investment. Therefore, Canada's position owes much to sound legislation that recognizes the high element of risk in exploration and development and also the exhaustibility of mineral deposits.

Nov 20, 1969

By Frederick B. Henderson

The US Environmental Protection Agency (EPA) has tried many regional and laboratory efforts to develop measurement and monitoring techniques using environmental remote sensing technologies. In 1997, the agency established the Advanced Measurement Initiative (AMI): This is a eadquarters-level program, operating under the auspices of the EPA Office of Research and Development. The program is one result of the April 30,1996 White House Conference on Advanced Monitoring of the Environment. The EPA was encouraged to work with other federal agencies to leverage its remote sensing capabilities and use them to improve the efficiency, cost-effectiveness and flexibility of environmental measurement and monitoring for regulatory compliance and reinvention. During the fall of 1996, the EPA and the Department of Energy developed an interagency effort to broaden the use of governmental technologies for environmental measurement and monitoring. In addition, the EPA and the National Aeronautics and Space Administration (NASA) conducted joint workshops on the use of NASA remote sensing and other technologies for water quality and pollution applications. In the meantime, the EPA proceeded with an industry-proposed workshop to explore ways to cooperatively examine new research and to develop commercial remote sensing systems. It also examined how these systems might become accepted by the EPA in the regulatory and compliance processes. In particular, industry was interested in where new remote sensing capabilities might fit in with EPA's efforts at regulatory reinvention. Historically, the mining and petroleum industries have been reluctant to experiment with or use environmental remote sensing. They were concerned with the unknown liability from potential discovery of previously unknown environmental problems. Moreover, resource industries have been reluctant to use remote sensing for environmental applications where the EPA did not accept such data or information as part of the compliance process. Acceptance by the EPA of these advanced measurement and monitoring technologies (AMMT) will be a major reason for industry's increasedd use of remote sensing in environmental "applications for regulatory compliance. In July 1997, the EPA Office of Research and Development hosted at the Colorado School of Mines a stakeholders workshop on the AMI program and industry-government collaboration. The workshop's aim was to demonstrate the usefulness of AMMT technologies for environmental applications. Stakeholders included the mining and petroleum industries; environmental services companies; state environmental agencies and local governments; remote-sensing, value-added companies and data suppliers. The workshop used specific technologies and applications as a way to develop collaborative demonstration projects for several AMMT technologies covering different environmental problems. The workshop focused on the use of highly sensitive hyperspectral (very narrow spectral bands), geographic information systems and surface mapping to identify active acid-producing mine dumps and wastes from benign wastes at Leadville, CO. NASA's advance infrared imaging spectrometer (AVIRIS) was the instrument used. It was developed at California Technology's Jet Propulsion Laboratory. The EPA, the US Bureau of Land Managment (BLM), the US Geological Survey and several environmental service contractors sponsored the overflight and data evaluation. The AVIRIS study demonstrated reliability (95% correct surface mineral identification) and cost-effectiveness of this technology to accurately map and discriminate active acid-producing mine wastes from benign wastes. It could also predict which streams would be effected by acid and toxic mineral drainage. The BLM'said that the AVIRIS overflight could save it $500,000 a year in surface sampling costs at Leadville. The AMI workshop further outlined five 1997 funded AMI projects of potential interest to the mining industry. They were: ? Mine waste characterization using remote sensing methodologies at Asarco's Ray Mine in Arizona. ? Predictive emissions development and testing in

Jan 1, 1997

By Tracy Morris, Shijie Wang

Preparative Continuous Annular Chromatography, or P-CAC, is an innovative separation technology, a unique approach to high-performance chromatography for the separation of PGM component mixtures from solutions. P-CAC consists of inlet/distribution head and outer/inner cylinders, and bottom plate/fraction-collection as well. P-CAC has been applied in biotechnological and pharmaceutical downstream processing. This was the first time to explore an efficient PGM separation and recovery at the Copper Refinery. Laboratory trials with using a chloride solution for raffination for PGM are described and the tests results are presented in this paper.

Mar 1, 2017

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By M Fimeri, R Williamson

Sample sizing in the iron ore industry requires significant manual effort to collect, transport, and sieve the samples as well as record, process and report the data. Efforts have been made to automate this process, which essentially emulate the manual process, except that a person is replaced by a robot. Even in these cells, the sieving and sizing operation consumes a significant proportion of robot time. The proposed doubling of production from AustraliaÆs iron ore mines over the next five years will place increasing pressure on sample sizing and interest is increasing in alternative automated methods. One such method is the adaptation of computer vision technology which has been successfully introduced into the mining industry in a range of applications including feed size distribution to SAG mills and oversize detection from screening stations. The limitation of this technology is that only the top surface is visible and this is used as an indicator of total size distribution. Obviously in a sample plant, where 100 per cent of the sample must be measured for acceptable quality assurance, this approach is unacceptable. In order to capture 100 per cent of the sample using computer vision technology a monolayer must be formed either by spreading the sample across a moving surface, such as a conveyor or vibrating platform, and passing this under a camera. This will become a æsurgingÆ load which presents specific problems for some types of computer vision systems, namely those relying on a 2D approach. In this paper a 3D computer vision technology will be described which overcomes the problems associated with measuring particle size in a monolayer and experimental results will be presented which demonstrate its effectiveness for lump and fine iron ore sample size measurement.

Jan 1, 2008

By J. Marbeau

In this paper, a geostatistical study of the North Butte roll type uranium deposit is presented. The geostatistical procedure applied takes into account the varying direction of the roll front for reserves calculations. For variogram calculation, the roll front is unfolded thereby allowing estimation of the variogram in directions parallel to and perpendicular to the roll front. Variograms calculated in unfolded space show strong directional anisotropies consistent with the anticipated configuration of the deposit.

Jan 1, 1991

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By Bin Xu, Qian Li, Xin Min, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The ringing characteristics of acid and alkaline iron ore pellets powder in kiln were studied by the thermodynamic calculation using software FactSage7.0, roasting experiments using briquetting method and analysis of SEM-EDS. The thermodynamic calculation demonstrated that liquid phase could be generated from alkaline pellets powder at a lower temperature and the amount of formed liquid phase was much more than that from acid pellets powder at the same temperature. Roasting experiments indicated that the compression strength of alkaline pellets powder briquettes were also higher than that of acid pellets powder briquettes. Additionally, the analysis of SEM-EDS suggested that the alkaline pellets powder briquette presented more liquid phase and a more compact structure comparing with the acid pellets powder briquette, which was consistent with the results of thermodynamic calculation and roasting experiments. Hence, in comparison with acid pellets powder, alkaline pellets powder is much easier to ring in the kiln.

Mar 1, 2017

By Andy L. Shaffer

A novel liquid settlement system (LSS) was installed in advance of mining at a western United States (U.S.) longwall mine to measure total roof sag from the time of cutting to days after mining during gate road development. The system was used to compare differences in roof sag between conventional place-change mining using a Joy continuous miner and a Fletcher roof bolter and mining using a miner-bolter. The LSS was installed with an intrinsically safe, miniature data acquisition system (MIDAS) to record roof response at four locations in the same gate road. The system utilized pressure transducers to measure roof sag by the principle of falling head (fluid pressure) in fluid-filletubes installed in the immediate roof. Details of the LSS design, installation, data collection, post-processing, and future applications are discussed.

Jan 1, 2014

By AIME AIME

AT A meeting of the Iron and Steel Institute held in London on May 6, Dr. J. E. Stead was formally inducted into the chair by Dr. Eugene Schneider, the retiring president. After presenting the Bessemer gold medal to Harry Brearley, of Sheffield, England, for his distinguished services to the British steel industry, Doctor Stead delivered his presidential address, a masterly review of iron and steel making progress during the past 50 years, emphasizing economy in production, and pointing out suggestions for future improvement. A considerable portion of the address was devoted to blast-furnace operation.

Jan 1, 1920

By A Trench, S Ulrich, S Hagemann

A synthesis of reported All-In Sustaining Costs (AISC) for 57 Australian gold mines in the period 2014–2016 reveals for the first time the clear influence of grade upon cost performance, most evident in gold-only underground mines. Past syntheses of costs on a single quarter basis have viewed grade as potentially subordinate to other factors such as production scale, mine geometry, mineralisation style and a combination of other mining-related costs. Better understanding of the grade to cost relationship on both an individual mine and whole-of-portfolio portfolio basis is needed. Insight into the roles and trade-offs between other cost-determining factors will aid the future sustainability of the gold mining sector in Australia and assist in targeting prospects for future resource growth and development. While the overall trend is toward higher-grade mines displaying lower costs and vice versa, the grade to cost functions appear radically different between mines based on time-series data. The median cost of Australian gold production in the final quarter of 2016 was A$1081/oz. The threshold for lowest cost quartile production was A$965/oz. Underground production now dominates Australian gold output – with 71 per cent of ounces originating from operations that are either entirely underground or hybrid pit/underground mines. Scale economies are evident, with smaller mines predominately among the higher cost producers. For mines of equal grade, open pit mines are lower cost than underground operations. Reserves are modest, with a median mine life for underground operations of 4.7 years based on current production rates. Reserve additions at mines are likely constrained not only by the finite nature of mineralisation at each mine but also by the geometrical difficulty of accessing suitable drilling locations to test for reserve extensions.CITATION:Ulrich, S, Trench, A and Hagemann, S, 2017. Towards an understanding of production costs at Australia’s underground gold mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By H. D. Baylor

This paper, describing the operations of the Louisville Cement Co. in quarrying limestone for the manufacture of quicklime, is one of a series being prepared for and published by the United States Bureau of Mines on stone quarries throughout the United States. Those papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author acknowledges the assistance of J. H. Lemmon, plant superintendent, Charles Taylor, plant engineer, and F. H. Compton, chief engineer, of the Louisville Cement Co. in the compilation and preparation of this paper.

Jan 1, 1932

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017