Search Documents

By G. E. McElroy

Economic solutions of problems of mine-ventilation improvement can be found by mathematical analyses of alternative methods of procedure, but, in the case of our older bituminous-coal mines, the airway network is usually so complex that mathematical solutions are too tedious to be practical. Recourse usually is made to extremely costly and uncertain trial-and-error procedures with the existing layout and equipment. The resulting errors often prove costly and sometimes create hazardous conditions. Both the economic and safely aspects of alternative methods of ventilation improvement may be rapidly and cheaply investigation with analogue computers. An electrical analogue computer, designed and built especially for analyzing mine-ventilation-distribution problems, has been placed in service by the Bureau of Mines at its Pittsburgh, Pa., Experiment Station. It is a nonlinear, low-voltage, fluid network analyzer of a type developed by Malcolm S. Mcllroy, professor of electrical engineering at Cornell University. It was designed in close coopera¬tion with Professor Mcllroy and built by the Standard Electric Time Co., Springfield, Mass. It is the seventh unit of this type to be placed in service and the first designed for mine airflow problems. The other six were designed for either water- or gas-distribution analyses. Three are much larger and more expensive units. The largest unit has a capacity of 20 sources, 576 mains, and 180 loads, or regulated-flow paths. The Bureau unit has a capacity of 5 sources, 128 mains, and 48 loads.

Jan 1, 1954

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By Clarence Hall, Charles E. Monroe

Squibs, Fuse, and Detonators It has been made clear in the discussion of combustion and explosion and the description of various explosives that they can be caused to explode by various means. All of them can, under some circumstances, be made to explode by fire. Some of them can be caused to undergo a detonating explosion by setting off a detonator in contact with them. In blasting use is made of both these means for setting off explosives, the means used being determined by circumstances.

Jan 1, 2010

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By George C. Riley

While the general public has little knowledge or appreciation of either the mining or explosives industries, modern civilization could not exist without them. They are to-day the key industries of the world. In common with many other industries the demands of the war greatly stimulated the production of explosives and the research necessary for such increased production. Production, supplies of all kinds, munitions of all sorts and then again production, practically regardless of cost, were the first reactions to the imperative war demands of the governments of the world. Following the war there was a momentary lull, then first gradually but with quickening acceleration, particularly in a recent slump, the situation was reversed - cost and not production was the dominant factor. Some industries readjusted themselves very rapidly and completely. Others were but partially re-adjusted and others again only carried out the process of deflation in certain departments. The explosives industry in Canada has not only thoroughly deflated itself, but has learned to apply to commercial disruptive explosives, the best, most efficient and most economical methods of manufacturing developed during the war. As a consequence, miners have at their disposal to-day better and more different kinds of compressed energy than ever before in all the long history of mining.

Jan 1, 1925

By J. G. Eisele

Solvent-extraction characteristics of dodecyl phosphoric acid (DDPA) were investigated to determine its potential as a fractional or selective extract-ant for individual elements in a rare-earth-yttrium mixture. The DDPA is an effective extractant for splitting rare-earth mixtures into light and heavy subgroups. Yttrium normally extracts with the heavy rare-earth elements but may be shifted toward an extraction sequence with the light rare-earth elements by increasing the pH. Elements in the light and heavy ends of the rare-earth series can be separated from middle-group rare-earth elements by using diethylenetriaminepentaacetic acid (DTPA) as an aqueous phase counter-extractant. Hydrogen-ion dependency of the distribution coefficients differs from that reported for similar systems at tracer-level concentration.

Jan 1, 1965

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By Nehad Elsafty

It is always necessary to expand existing buildings, so that they could meet the growing societal needs. Compared with demolishing them and then constructing new ones, the expansion of existing buildings could not only reduce project cost, but also save the use of energy and raw materials in projects. Therefore, it is widely adopted in most under-developed countries. However, the expansion of existing buildings is not an easy task. It has been involved with a lot of issues in defining the scope of work, planning landscape, managing construction activities, etc. This paper investigates the potential challenges in expanding existing buildings. The project of expanding the Al-Agoza Hospital, one of the biggest and oldest hospitals in Cairo, Egypt, is selected as a case study. In the case study, the project documents have been carefully reviewed. The project engineers and the health-care professionals working in the hospital have been interviewed. This way, the point of views from the owner, the architect/engineer, and the contractor have been taken into account. Several lessons are learned through the discussion with these people. The results from this paper are expected to provide pieces of useful advice and suggestion for the expansion of existing buildings in the future.

Aug 1, 2013

By R. H. Derammelaere

With renewed interest in coal slurry pipelines in China, Indonesia, Australia and Canada for electric generation, it appears worthwhile to update the relative economics of transporting coal by slurry pipeline. Three slurry pipeline technologies are evaluated for the commercial transportation of 3.0, 6.0, and 9.0 million tonnes per year (MMT A) example cases, over distances of 250 km, 500 km and 1000 km.

Jan 1, 1998

By R. H. Church

As part of the research effort of investigating the effects of microwave energy upon the chemical and physical properties of different minerals and ores, the Bureau of Mines has conducted basic research into identifying those properties of minerals that are affected by microwave energy, namely, the dielectric constant and loss tangent. These properties were determined utilizing the theory of microwave propagation in a coaxial waveguide filled with a dielectric material and measuring the input impedance with an RF impedance analyzer that operates from 1 MHz to 1 GHz. By knowing the microwave frequency and filling the waveguide with a powdered mineral, the dielectric properties of the mineral sample were determined. From these dielectric properties, theoretical microwave heating characteristics of each mineral could be calculated. These same mineral samples were then irradiated by a 915 MHz 30 kW variable power microwave oven and dielectric heating studies were performed. A comparison of the theoretical heating characteristics and the results from actual dielectric heating studies was conducted to evaluate the dielectric property measurements on each mineral. This report presents the results of the Bureau's research in identifying the dielectric properties of low-loss minerals according to the mineralogical classification scheme along with their irradiation studies. Though far from complete, this study represents some of the more frequently encountered low-loss minerals.

Jan 1, 1988

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By J. M. Mutmansky, C. Lee

"Measurement of the size and elemental characteristics was performed on airborne coal mine dust samples collected by multi-stage cascade impactors as well as channel samples of the geologic materials. Size distributions were obtained using precise weighing techniques on the impactor substrates. Elemental analysis on the samples was performed by the proton-induced x-ray emission (PIXE) method, a rapid and non-destructive method of multi-element analysis.The various analyses were performed on 9 major and 21 trace elements. The results indicate the importance of intake air and shuttle car movements as sources of dust. The association of coal dust characteristics with channel samples was investigated using the coefficient of proportional similarity as a statistical measure. Results show a strong relationship between major elements and the geologic material being cut but a similar relationship between trace elements and geologic materials is not consistent.1. INTRODUCTIONThe most significant occupational disease in the coal industry is known ·as coal workers' pneumoconiosis (CW'P). While CW'P has existed for centuries, its mechanism of occurrence and association with coal dust has been well understood for only a few decades. In the 1930s, the significance of this disease led state and government officials in the USA to perform extensive epidemiological and environmental studies in the major coalfields. Study of these results plus later studies in the coal producing countries of Europe eventually led to the dust regulations that appear in the Federal Coal Mine Health and Safety Act of 1969.The impacts of the 1969 act were a productivity decline and increased production cost. Many analysts attributed this in large part to difficulties in complying with the new dust standards (Brezovic 1981). However, compliance was met in most continuous miner sections rather quickly. The remaining problem area is that of longwall mining where the procedures and layout of the minin~ system make it difficult to meet the standards."

Jan 1, 1989

By C. O. Campbell

THE recognition by C. W. McKee, field engineer for Springer Sturgeon Gold Mines, Limited, in the fall of 1940, of the economic possibilities of a small outcrop of baryres near Pembroke, in Hants county, Nova Scotia, followed by aggressive exploration and development by the Company, has placed Canada for the first time in its history in the position of becoming a major producer of barytes and its products. In past years, production of this mineral in Canada has been unimportant. Thus the coral output from 1885 ro 1933, inclusive, amounted to only 41,027 short tons, following which there was no production until 1939. Deposits in Nova Scotia, and particularly in the Lake Ainslie district, Cape Breton, have been the main source of supply, with a production between 1866 and 1925 of 31,689 tons. Following the examination of the outcrop of baryres near Pembroke by Mr. C. W. McKee in October, 1940, the area surrounding it was trenched, and, as this work gave encouraging results, a diamond drilling programme was commenced. A grid system was laid our and sixteen holes aggregating 2809.3 feet were put down, spaced at 100-foot intervals, the deepest hole being 300 feet. This drilling outlined a body of high-grade baryres over 600 feet long and 200 to 250 feet wide, with an average depth of 120 feet and estimated to contain well over one million tons of ore. The limits of the body were reached on the west, north, and southwest, but the drilling was suspended before the eastern limit was determined. Quarrying operations, and construction of a 100-ton mill, were commenced in February, 1941. The mill was placed in operation on May 29th, and on June 15th, eight months after the initial discovery, the first shipment of 2,500 long rons of milled baryres was made to Trinidad, British West Indies.

Jan 1, 1942

By Magnus Evertsson, Rebecka Stomvall, Josefine Berntsson

"Understanding the effect of particle shape on dry rheology is considered to be an important aspect in order to replace natural sand used in concrete with manufactured sand. Crushed particles from solid rock are normally less rounded and have less equally shaped dimensions compared to natural sand. Thus, the flowability and workability of the concrete will be different. In previous research, it has been demonstrated how different crushing techniques affects the shape of the particles. In many cases it is believed that Vertical Shaft Impact (VSI) technology is a way forward to replace natural sand. To be able to study the effect of VSI at the smaller fractions (63-2000 µm) sufficient measurements methods to determine particle shape are required. Optical tools to analyze the aggregates would make it possible to study a large amount of particles at small fractions. The determination of particle shape of aggregates is challenging since the shape is highly irregular and the size span of particles are very large. This study aim to evaluate one of the available optical tools, the Camsizer, for digital imaging determination of shape and size distribution. The available default shape parameters of the Camsizer are studied to understand the meaning of the parameters and their suitability for determining the quality of manufactured sand. To evaluate the capacity to determine particle shape, tests are made with 35 different materials. The results are compared with the dry rheology measured with the standardized "flow cone" test. Dependence has been previously proven between particle shape and the mass flow rate in the cone. Three different shape parameters, aspect ratio, sphericity and symmetry, are studied with the Camsizer and the results are compared with the mass flow rates in the cone. The results indicate a strong linear relationship between the optical parameters and the flow cone test."

Jan 1, 2014

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By Joseph F. Davies

To gain knowledge of the actual accident hazards present in Kentucky coal mines, reports of fatalities during 1931, 1932, and 1933 have been analyzed and the pertinent factors included in tables, accompanied by some discussion and recommendations for the reduction of accidents from particular causes. ACKNOWLEDGMENT This study was made possible through the cooperation of John F. Daniel, chief of the Kentucky Department of Mines, who made available department records, in addition to the monthly bulletine issued by his office reporting these fatalities.

Jan 1, 1934

By Ervin P. Fuchs

Volume II of this report presents the vibration data, octave band data, one-third octave band data and narrow band (amplitude versus frequency) data for ten mining machines. These ten mining machines include a Goodman 968-2 Loading Machine, a Lee Norse 245 Continuous Miner, a Jeffrey 120L Continuous Miner, a National Mine Service 3080 Continuous Miner, Acme D-1 Roof Bolter, a Lee Norse 265 Continuous Miner, two Jeffrey Locomotives, a Joy CD-71A Coal Drill and a Jeffrey 100L Auger Miner. Volume J of this report presents the effects of underground environment and loading conditions on noise levels of coal mining equipment

Jan 1, 1979

By G. L. Oldright, Virgil Miller

"ACKN0WLEDGMENTSThe data given in this paper were collected at the Bunker Hill smelter through the courtesy of Stanley A. Easton, the vice-president and general manager, Frank M. Smith, the smelter director, and with the assistance and cooperation of A. F. Beasley, the smelter superintendent, and his staff members.THE BLAST FURNACE AND PLANTThe general lay-out of the recently built (1917) Bunker Hill plant has been given in the technical press in articles that were cited in Report of Investigations 3088. In addition it may be noted that the description of an ideal smelter given by Riddell 5 a year later fits the Bunker Hill smelter very well, with some changes, such as the location of the stack, made necessary by topography. For purposes of this article on the blast furnace it may suffice to state that the plant is one of the ""side hill location"" type. The various successively lower benches may roughly be considered as made for (1) the stack, (2) Cottrells and bag houses, (3) Dwight and Lloyd sintering machines with the equipment or bins for handling or mixing the feed and storing the finished product, sinter, and (4) the blast furnace feed floor with a slightly rising gradient to the bottom of the bins for sinter, feed, and take. The lowest bench (5) might be considered that of the blast furnace tapping floor at which or at appropriately slightly lower elevations are located the units for softening, refining, and treating precious metals, and for casting and loading lead. A very careful study of grades was made in order to be able to handle the products easily. All units were left with at least one end open to permit expansion of the plant, it desired, and each unit was separated from the other, evidently so that the operators on one level would be annoyed as little as posssible with the products made on another."

Apr 1, 1931