Search Documents

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By Anthony Spearing

There are approximately 68 million rockbolts installed annually in underground coal mines in the USA (Tadolini and Mazzoni, 2006). The most utilized is the passive fully grouted resin rebar bolt, which constitutes almost 90% of the primary support in US underground coal mines. Resin-grouted rockbolts are a very effective and safe support, but their performance still needs to be further optimized and improved. This paper investigates their performance and suggests operating conditions to optimize the performance of resin-grouted rockbolts. In addition, this paper discusses a small-scale test that can also be used to evaluate the performance of rockbolts that is quicker, easier, and less costly than short encapsulation tests.

Jan 1, 2014

By Yu A. Chernegov

Building up the USSR's economic strength was the result of all the achievements and successes of our economy. The Soviet Union was the first to begin planned guidance of the economy. The mining industry of the USSR, which holds the first place in the world output of mining production, has always been considered as the main raw materials basis of the country's economy. High and stable development rates are a feature of planned economic management, based on the social ownership of the means of production. During the past ten years from 1965 to 1875 the national income used for consumption and accumulation increased practically by 1.9 times. There has been no inflation, no unemployment in the Soviet Union for about forty years already. High and stable growth rates of the production of mining industries and that of the branches, which are their direct consumers are characterized by the data in table I. The achievements and successes of the economy's development are to a great extent determined by the three planning components, which are as follows:

Jan 1, 1977

By Z. Kokesz

The following paper presents the results of geostatistical studies of the selected hard-coal deposits in Poland. Geostatistical methods were applied mainly to the characterization of variability structure of the coal seams thicknesses as well as sulphur and ash contents in the coals. Results imply that the accuracy of coal reserves estimations can be improved if kriging method is applied. Kriging allows predicting more precisely the values of such parameters as thickness and sulphuring content.

Jan 1, 1993

By R. Bakish, M. A. Badiali, N. W. Kirshenbaum

One pound of ultra pul-e molybdenum has been produced containing both metallic and nonmetallic impuvities close to or less than the limits of detection. various purification methods were investigated; althouglz the use of move than one purification step was consideved, it was found that a single, caefully-controlled sublimation of MoCl5 yielded a highly puvified product without prior treatment or recourse to repeated sublimation. Hydrogen reduction of MoC1, to metal was attempted at atmospheric pressure; however, reduced pressure was necessary to obtain substantial yields. The tubular deposits of metal were consolidated into bulk fovm by electron beam melting undev high vacuum yielding a very low gas content. Boblems involved in monitoring the puvity of these materials and analytical results obtained are also presented. THE pronounced effect of even trace amounts of impurities upon fundamental properties of materials is well known to metallurgists and solid-state physicists. Consequently, groups interested in basic studies of metals have in recent years immensely stimulated the preparation and production of numerous ultra-pure metals. Increased demand by scientists for these high purity materials has necessitated development of facilities to prepare them in significant quantities; the procedures reported here were devised to produce significant quantities of ultra-pure molybdenum. Previous work performed in the field of vapor phase purification and hydrogen reduction of several other refractory metal chlorides had demonstrated valuable techniques applicable to molybdenum.' Various purification and reduction steps were individually investigated. Those procedures which showed the most favorable results with respect both to attainment of high purity and to ease of operation were then incorporated in the process utilized to produce the metal.' STARTING MATERIALS It is well known that because of differences in volatility, chlorides may be separated by fractional distillation. It was presumed that distillation of molybdenum pentachloride offered a simple and straightforward method of purification due to its relatively low boiling point. Alternatively, sublimation of the solid chloride also appeared feasible since MoC15 has both a reasonably narrow temperature range in which it exists as a liquid (a property typical of refractory metal chlorides) and a low enthalpy of sublimation. Pertinent thermochemical data of MoC15 are given in Table I. It should be noted that this compound must be handled with care as it is extremely hygroscopic. Anhydrous MoC15 was obtained from the A Metal Climax Co. METHODS OF PURIFYING MOLYBDENUM PENTACHLORIDE Distillation. It was expected that distillation methods, while affording an efficient purification, would prove simple to control and would have a higher production rate than sublimation processes. Also considered was the possibility of effecting a high degree of purification by using both these volatilization methods in conjunction—possibly a distillation followed by sublimation of the solidified condensate. Distillation of MoC15 was investigated using a single stage distillation column packed with chemically resistant glass beads. Heating coils were wound around the column and collection tube (condenser). As-received MoCl5 was charged into a flask connected with the column using a side loading arm under an argon flow. After the column and condenser were brought to about 270" and 210°C, respectively, the apparatus was lowered until the flask was fully immersed in a constant temperature fused salt bath maintained at about 285 °C. Distillation was continued for about 10 or 15 min until 50 to 70 g of distillate had been collected. Analyses of these distillations indicated that several elements, e.g., Cu, Fe, Ni, Cr, and Mg, were lowered in quantity although not all were removed to the same extent. The occurrence of Na, B, Si, and A1 in the distillates appeared to be due to contamination, possibly from corrosion of the pyrex glass. An improved distillation system of larger capacity and longer distilling column was built. Improvements were effected in lowering the amounts of such impurities as B, Mn, Ni, Na, Mg, Cr, Cu, and Fe. These studies were pursued concomitantly with efforts to purify by sublimation; it was subsequently found that although improvements in purity were obtained by distillation, sublimation processes were simpler to control and effected a high degree of purity.

Jan 1, 1963

By Eugene Holman

UINQUESTIONABLY the petroleum industry not only can supply the world's present oil requirements but even can meet a considerable increase in demand if it should come. The United States produced last year 1 1/3 billion barrels of crude oil, or more than 60 per cent of the world's total. It could have provided more, if needed, because we has a large shut-in crude producing capacity. Our refining capacity of 4,500,000 0 barrels per day is more than 2 per cent above our average refinery run for 1940. Adequate crude supplies and manufacturing facilities also exist outside of the United States. Large crude reserves exist in South America, in Iran and Iraq, in Russia and Romania, in Sumatra and adjacent islands. The refineries of the Dutch West Indies, of Iran, and of the Netherland East Indies are well located in relation to crude reserves and world trade lanes. Furthermore, flexibility in the manufacturing facilities permits adjustment of yields to meet a considerable range in variations between demands for products. Only with regard to 100-octane aviation gasoline is there any apparent refinery problem. Even here so far as this country is concerned, additional refining facilities can be installed well within the time that would be required to turn out the airplane engines which will use this super fuel.

Jan 1, 1941

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By K. C. Corin

It is well known that the grinding circuit plays a crucial role in flotation. The effect of pulp chemistry during grinding is often overlooked. It is believed that the surface properties of the minerals can be adjusted during flotation rather than during grinding. However, recent development in surface analysis techniques (TOF-SIMS, XPS, and AES etc.) have proven that the hydrophilic iron hydroxides formed at the mineral surface during grinding make it difficult for collector adsorption, which may result in poor grades and recoveries of the valuable minerals. This study investigated the effect of the pulp chemistry conditions during milling and the subsequent effects on flotation performance of an Nkomati ore. The results have shown that there was approximately 10 % increase in Ni recovery, when the ore was ground at a dissolved oxygen (DO) concentration of 0 ppm (DO-0) in comparison to no gas control during the grinding stage. However, when the pH was changed from 9 to 11, no gas control resulted in a 20 % decrease in the Ni recovery compared to only 5 % decrease in the Ni recovery at DO-0. A noteworthy observation is that controlling a combination of DO and pH during grinding is of critical importance for better floatability and selectivity for such a system. It also became clear from this study that the presence of oxygen is critical to the consumption of xanthate, which is consistent with the general literature. It has been established that grinding at lower DO levels/redox potentials (Eh) in the presence of xanthate significantly improves the flotation performance of the valuable minerals.

Sep 1, 2012

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By T. Weatherwax, A. Rai, J. Poor

"This paper provides an overview of the current use of auxiliary ventilation products and the challenges with limited air quantity in dead-end entry or working faces. The PVC’s low frictional factor, low physical constraint and minimum leakage properties were ideal to develop as ventilation duct in conjunction with the concept of ""Made in the US and Used in the US"". The PVC duct supports the operational and total cost of ownership with on-going success. This paper will discuss the continuous improvement made in ventilation ancillary products for optimum results. The paper will also cover mine site usage of second generation PVC vent duct underground and the results from the operational and technical side making a difference in health and safety and overall auxiliary ventilation. INTRODUCTION The Barrick Turquoise Ridge Inc. (TR) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone, siltstones, and mudstones. The weak nature of the ground facilitates the need for underhand cut and fills mining methods.Mining Method; Underhand cut and fill: The mine uses underhand cut and fill method which has 12’x12’ and or 14’x14’ top cuts with several different size undercuts. The ore body is accessed off of a secondary tertiary heading, utilizing a heading with a cross section of 14W x 14H or 15W x 15H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the ground conditions and drift dimension. An example of a typical topcut and associated undercut layout is shown in Figure 2."

Jan 1, 2016

By Jack Wright

The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines5-8 and Federal Geological Survey,9-11/ as well as articles in engineer and geological journals12-14/ placed special emphasis on the importance, interpretation, and application of water analyses. One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for Analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, "In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .," and, "The waters of each oil field are chemically different from those of another field." The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the a geological formation in different localities or oil pools.

Jan 1, 1957

By Dion Pastars

Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective, the system requires the mixing of the catalyst and mastic components of the resin, as well as shredding of the laminate cartridge that contains the resin. An unknown measure is the load transfer characteristics of a bolt where the resin is well mixed but remains encased in the cartridge (gloved). Laboratory and in situ field investigations have been undertaken to quantify the performance loss due to mixed gloved bolts. This work showed repeatable results, indicating serious performance loss of the gloved and mixed system, with load transfer approximately 10- 15% of a non-gloved system (MacGregor, 2004). The in situ testing has demonstrated the relationship between the adhesion qualities of the resin and the mechanical interlock generated by radial confinement with progressively increasing tensile load. Effective load transfer is defined by the ability of the system to sustain shear stress on the bolt hole wall.

Jan 1, 2005

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. Surveys of Ra226 contamination of liquid wastes from uranium mills indicated that the Vanadium Corporation of America plant at Durango, Colo., had one of the more urgent problems. A possible procedure for minimizing the waste disposal problem was to reuse the waste solution in the mill--in effect, erasing the need for disposal of liquid waste. In examining this possibility, interlocked bench-scale leaching and solvent extraction tests simulating the Durango flowsheet were made. The simulated reuse of barren raffinate for leaching and washing was carried through three separate campaigns of 9, 12, and 35 cycles each.

Jan 1, 1961

By A Calderon, J Harris, M Shi, D Viswanathan, C Ribeiro Duthie, P A. Kirsch

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the current environment of corporate social responsibility life-of-mine planning considers that mining activities should be conducted in the best environmentally, socially and economically acceptable way for the entire life of the mine (ie from exploration to decommissioning and closure). In this context, the health impacts of mining extend throughout the life of the community from worker injury and chronic exposure to communicable and non-communicable causes of illness, through to family and community health and well-being. At the inaugural Life-of-Mine conference in July 2012, the authors proposed the life-of-mine in the life-of-community (LOMLOC) matrix as a framework for understanding issues at the interface between resource extraction operations and the surrounding environment.This paper reviews and compares health activities extracted from social and environmental reports published by selected major mining companies with American operations in Canada, Colombia and Brazil. These corporate approaches to public health management are mapped to the LOMLOC matrix to identify and compare trends and behaviour in corporate health investments. This analysis of how companies approach and prioritise health issues in the context of different regions, cultures and environmental drivers will serve as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.CITATION:Ribeiro Duthie, C, Calderon, A, Viswanathan, D, ?Shi, M, Harris, J and Kirsch, P A, ?2014. Resource company investments in health – a life-of-mine / life-of-community perspective across America, in Proceedings Life-of-Mine 2014 , pp 349–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J Bang, I-H Jung

Ti is an important constituent for steels and superalloys. During the continuous casting process and ElectroSlag Remelting process (ESR), Ti in molten steel and superalloy can have chemical reactions with casting flux and ESR slag containing CaO and CaF2. In order to investigate such exchange reactions, the understanding of the (Ca,Ti//O,F) reciprocal slag system is prerequisite. In the present study, a coupled phase diagram experiment and thermodynamic modelling of the (Ca,Ti//O,F) reciprocal system was performed. In particular, the phase diagram of the CaF2-TiO2 system was experimentally investigated by Differential Thermal Analysis (DTA) experiment and quenching experiments followed by Electron Probe MicroAnalysis (EPMA) phase analysis. The Gibbs energy functions of all solid and liquid phases in the (Ca,Ti//O,F) reciprocal system were optimised to reproduce the present data and all available reliable experimental data in literature.

Jun 19, 2024

By W. Miola, R. V. Ramaoi

"The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of /ow-temperature, radio-frequency ashing (LTA) and infra7 red analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods.In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified. IntroductionThe literature on coal-mine airborne-dust control has identified a need for a better understanding of the sources, mechanisms and amounts of quartz in mine airborne respirable dust (Althouse, 1984; Jankowski, Nesbit and Kissel, 1985; Ramani 1988; Qin, 1988; Bhaskar and Xu, 1990; Bhaskar and Li, 1992; Ramani, Qin and Miola, 1991 ). To understand the quartz content in the source materials, bulk samples of coal and host rock must be analyzed. Establishing an analysis procedure for determining the quartz content in bulk-coal and host-rock samples is necessary for identifying the sources of quartz in mines; for establishing the relationships between the quartz contained in the source and in the airborne dust; and for controlling the content of quartz in the mined product and in the airborne respirable dust."

Dec 1, 1996

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

By Otis M. Clarke

Although most bauxite mined is used to make metallic alu¬minum, more than a million tons of bauxite is used annually in the United States in the manufacture of refractories, chemicals, abrasives, and cement. Raw material requirements are becoming increasingly difficult to meet because high-grade bauxite, required for some uses, is limited. The supply of raw material for high-alumina refractories is most critical because a low-iron bauxite is needed. Although there are substantial bauxite reserves in the world, bauxite suitable for use in refractories is limited to a few districts.

Jan 1, 1977

By W. A. Scheuch, J. Walter

Ordinarily secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered'metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must, just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product. Secondary Copper Used for Wire Bars Only clean secondary copper of the grades known to the trade as Numbers 1 and 2 are melted for wire-bar manufacture. This material, supplemented by that obtained from various manufacturing processes

Jan 1, 1930