Search Documents

This research is about human development and socio-economic progress of the main mining areas of Chile in the period 1990 - 2007, and especially about the positive effects that mining activity has on poverty reduction and indicators related to the Millennium Development Goals of the United Nations. The analysis is doubly interesting, if one considers that the economic and social developments in Chile, recognised and prominent among the Latin American economies and developing nations, are more evident in mining areas as Tarapacß and Antofagasta (northern Chile), which concentrated than more 70 per cent of investments and mining assets in the country. Additionally, the study concludes with methodological reflections for the evaluation of socio-economic impact in the mining industry in developing countries.

Jan 1, 2009

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

By W. H. Young

MOST OF THE key items in the bituminous-coal and Lignite industry declined in 1954 compared with 1953. Production, consumption, exports, average value per ton, men working, and days worked all declined; however, in the field of mechanization, the percentages mechanically loaded, mechanically cleaned, mined by auger, and mined by stripping all increased, as did production per men per day. Production.-The output of soft coal in 1954-391.7 million tons- was 14 percent less than the 457.3 million tons produced in 1953. The lower production in 1954 was due largely to a sharp reduction in consumption in the United States and to a drop in exports.

Jan 1, 1958

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau's Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By A. L. Wilder, S. N. Dixon

Introduction Coeur d'Alene Mines Corp.'s largest precious metals property is located in the historic Rochester Mining District 40 km (25 miles) northeast of Lovelock, NV. The property encountered cold weather operational problems soon after its fall start-up in 1986 due to its elevation of over 1830 m (6000 ft). The problem of ice buildup on the heaps because of sprayed solution application was faced immediately. It was felt that allowing ice to build up all winter long until a spring thaw was impractical due to the large area under leach. Further, the operating cost and delivery schedule for a solution heating system was unacceptable. The development and installation of a leach solution distribution system using drip emitters made efficient, cost-effective winter operation possible. Other benefits of this system have also been observed and are discussed here. General process description 15,422 kt/day (17,000 stpd) of - 1.27-cm (-1 /2-in) crushed ore from the three-stage crushing plant are delivered to the leach pad using 77.1 t (85 st) rear dump haul trucks. The ore is drifted into place with a D-9 bulldozer. Leach panels are contiguous and are approximately 8861 m'(90,000 square ft) in area built in 6-m (20-ft) lifts. New panels are built on top of older areas to a final height of 61 m (200 ft). Each panel is ripped and cross-ripped prior to leaching. Barren solution is distributed to the heap using drip emitters at rates of 0.02 to 0.41 L/min/m2 (0.0005 to 0.01 gpm per sq ft), depending on the age of the panels. The pH of the leach solution is 10.7 with a cyanide concentration of 0.75 kg/t (1.5 lb per st). Approximately 50% of the silver and 80% of the gold are finally recovered. Pregnant solution percolates though the heap and flows by gravity into one of two 9.46 ML (2.5 million gal) pregnant solution ponds. The solution is then pumped to a conventional Merrill-Crowe process plant. Clarification takes place in three 9464 L/min (2,500 gpm) capacity filters. The solution is then pumped to a packed vacuum deareation tower for the removal of dissolved oxygen. Typical deareated solution contains 0.7 parts per million dissolved oxygen. Precipitation of gold and silver is accomplished by adding a zinc dust slurry to the deareated solution at the suction of the filter press feed pump. Precipitated gold and silver are recovered in three recessed plate and frame filter presses. Barren solution is discharged into a 11.7 ML (3.1 million gal) pond where cyanide makeup occurs. This solution is pumped back to the heap for further leaching. The precipitate filter cake, containing approximately 75% dore (Ag + Au), is then fluxed with anhydrous borax, soda ash, sodium nitrate and fluorspar to yield a neutral, bisilicate slag. The fluxed precipitate is then charged into a propane-fired melting furnace and heated to 1150° C (2100° F) for 3 1/2 hours. Slag and dore bullion are poured into conical cast iron pots yielding buttons of 800 to 1000 troy oz. The dore typically contains 98.5% silver and 1 % gold. Slag is crushed and tabled to recover the trapped dore blebs and beads. Concentrate from the table is returned to the furnace. Table tails are sent to the crushing circuit and out to the leach pad. Solution application The area kept under leach at Rochester is approximately 130 000 m2 (1.4 million sq ft). Barren solution is delivered to the pad at 21.2 kL/min (5600 gpm) for a resultant application rate of 0.16 L/min/m2 (0.004 gpm per sq ft). A traditional solution sprinkling system using No. 12 Senninger Wobblers with individual pressure regulators was installed at the onset of leaching activities. The Wobblers were placed at 9.1-m (30¬ft) staggered centers and were fed off of a gridwork of Yellowmine plastic piping. Solution flow rates were moni¬tored to each panel. The onset of cold weather with an average nighttime temperature of -12° C (10° F) made it apparent that continual operation would not be possible with the sprinklers. A significant amount of ice was built up on top of the heap, making maintenance and pipe removal dangerous, if not impossible. Leach solution application was restricted to daylight hours to inhibit ice formation. Process plant flow rates were reduced to maintain steady-state operating conditions. However, as daylight temperatures dropped below freezing, ice continued to accumulate due to the sprays. Besides the obvious operating hazards brought on by the growing icefield, there was also the potential environmental hazard associated with an early thaw melting the ice too rapidly for the solution containment facilities. One other option for preventing ice formation was heating of the barren solution prior to spraying. Initial plant design allowed for expansion of the propane storage and distribution system as well as modification of the barren piping for a solution heater. This option was not exercised because the operating costs for an adequate system would have been prohibitive, and timely delivery of a system was not available. An investigation was conducted on the various drip irriga¬tion products available, since subsurface solution applicators would eliminate ice formation altogether. Systems utilizing external flow emitters were ruled out because of their ten¬dency to clog when buried. Emitter systems using perforated tubing were also eliminated from consideration due to their inability to adequately control flow over required lengths of tubing. An in-line emitter system was finally selected which demonstrated clog resistance and adequate flow control, enabling direct burial.

Jan 1, 1990

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

President W. K. Dennison, Jr., called the final session of the Rocky Mountain Coal Mining Institute to order, and introduced H. A. Cornell, Portland Cement Association, Ft. Collins, Colorado. Mr. Cornell explained that the Portland Cement Association was not a sales organization, but is supported by the major manufacturers of portland cement. The research laboratories of the association are constantly endeavoring to improve the quality of cement, as well as promote new markets, new uses, and new ideas. The association works with engineers, contractors and universities, making available to them the results of their research. Mr. Cornell stated that numerous booklets and bulletins were available on request for any phase of construction with concrete. Mr. Cornell presented a film, "How to Make Quality Concrete," to the members of the Institute. D. W. Lyke, General Electric Apparatus Service Shop, Denver, Colorado, was introduced by President Dennison, who presented a film, "A-Hunting He Would Go." Following the film, Mr. Lyke stated that his firm was not confined to electrical equipment, but to all types of equipment, and asked the members to feel free to call for assistance at any time. These two films concluded the Manufacturer's Hour, and President Dennison opened the final business meeting of the session. Robert F. Bowie, of the Auditing Committee, read the Treasurer's Report, and complimented Mr. Whiteside on the commendable state in which the books were found. The Treasurer's Report is as follows:

Jan 1, 1960

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By A. C. Fieldner

IN the Wall Street journal for March 1, 1941, was a tabulation of the construction under way or under negotiation by thirteen iron and steel companies for a predicted increase in annual coke production of 3,165,600 tons. That even this figure was short of the mark is indicated by other plans, then being considered, for a later expansion of 2,610,000 tons additional. Considerable progress has already been made on thin program, for approximately 500 new ovens were put in operation in 1941. and well over 200 should be completed in 1942. These figures include a number of units that replace older and obsolete equipment.

Jan 1, 1942

By AIME AIME

DOUBT in anyone's mind that this is the age of metals, industrially speaking, could easily have been dispelled by attending the National Metal Congress in Chicago, Sept. 22 to 26. Iron, copper and aluminum; zinc, lead and nickel, often alloyed with each other or with some of a dozen minor metals, make the materials without which the modern world could not run. Science, pure and applied, is doing marvels in finding new mixtures, new alloys to meet new needs; in developing new means of rolling, fabricating, casting and welding metals cheaply-and effectively. These and related matters were the subject of 100 papers presented at 33 seperate sessions of the organizations that participated in the congress.

Jan 1, 1930

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By A. L. Engel

[This report presents results of investigations of problems assigned as ore-testing projects to the Ore-Dressing Section, Metallurgical Division, of the Bureau of Mines at the Mississippi Valley Experiment Station in Rolla, Mo., during the fiscal year ended June 30, 1940.]

Jan 1, 1941

By G. G. Campbell

"HistoricalBARYTES was mined in Nova Scotia as early as 1874 from a deposit at Five Islands, on the north shore of Minas Basin. The first record of the presence of the mineral at the Walton site appears in a report by Selwyn in l893, who states: ""Barytes in considerable quantity occurs in veins in lime-stones at Walton and Pembroke"". The exact site of the present workings was marked •on a map published by Fletcher in 1905.The economic •possibilities of this deposit, however, were not recognized until 1940, at which time we were at war with Germany, who up to that time had supplied 50 per cent of the world's requirements.At that time the Nova Scotia Department of Mines, recognizing the need for certain strategic minerals, induced Canadian Industrial Minerals, Limited, to send prospectors into 'the area to look for manganese. No manganese deposits were found, but a deposit of barytes was directed to their attention, and exploration and development work on the occurrence was proceeded with.IntroductionThe south shore of Minas Basin between the Avon river at Windsor and the Stewiacke river at Maitland has long been known as a potential source of mineral wealth. It had attracted the attention of mineralogists and in the past had produced considerable tonnages of manganese ore and gypsum. Depletion of ore in surface and near surface deposits resulted in a dwindling production, until today only deposits of gypsum are worked."

Jan 1, 1952

By X. Wu

A quantitative damage evaluation caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain energy buildup are identified and investigated. A methodology to evaluate the strain energy accumulation caused by overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude ML which depends on the seismic energy transformed from the stored strain energy released when the roof fails. A particle velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and damage area agree well with the field observations.

Jan 1, 1995

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950.s and 60.s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining mechanisation during and after this period led to that pneumatic devices being unable to treat run-of-mine coals with the desired efficiency. Since the 1960.s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. The process and the advantages and disadvantages are presented below.Further on new developments in the field of dry density separation of coal are reviewed and analysed. Test results of new dry coal separation methods e.g. new developed air jig and magnetic separator are reported."

Jan 1, 2003

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942