Search Documents

By C. Droun

"Low back pains account for about 13 per cent of all compensation claims made to the Quebec Workmen's Compensation Commission and cost the employers a sum exceeding ten million dollars. The frequency and cost of these health problems in Quebec metal mines are proportional to the provincial trends. An elaborate review of the literature on the causes, nature and prevention of low back pain is made in this presentation. A prevention program for low back pain has been designed in cooperation with a team of seven medical specialists and two physiotherapists for the Quebec metal mines. The program is especially designed for persons who have had low back pain, in order to prevent a recurrence, and for persons beginning to feel chronic difficulties. It is based on existing programs at the Hawthorne Plant of Western Electric Company and at Minnesota Mining and Manufacturing, but it requires a much different approach because of the nature of medical care available at the mining sites. The program is difficult because it involves a change of attitude for every employee and every supervisor. The program, so far, is beneficial because several men are now seriously engaged in an active program of reconditioning and because the problem of low back pain ie beginning to be seen from a new angle."

Jan 1, 1973

By A. Juganda, Jr. Bogin, S. A. Lolon, J. F. Brune, J. W. Grubb

"A longwall gob is mainly filled with broken rocks from the collapsed roof and becomes a porous medium where explosive methane-air mixtures can accumulate. In bleeder ventilation systems, this mixture can migrate out of the gob into the longwall face and other active areas in the mine during barometric or ventilation-induced pressure changes. When external pressures change, the gob does not perceive this disturbance instantly but with a delay due to air flow resistance in the porous gob material. The delay of gob response to outside pressure changes increases the pressure differential across the gob and may cause an outflow of explosive air mixtures from the gob into the adjacent bleeder entries. With computational fluid dynamics (CFD) modeling, researchers at the Colorado School of Mines have evaluated the impact of gob pressure fluctuations on the outgassing of the explosive gas zones (EGZs), the magnitudes and rates of pressure changes, the volumes as well as the potentials location of outgassing if it occurs. INTRODUCTION The air pressure field in underground mines is controlled by many factors such as operating fan settings, ventilation controls, surface atmospheric conditions, and other local events that can intermittently disturb mine pressure, including blasting, roof falls, or inundations. Mine fan settings are rarely changed. Mine atmospheric pressure fluctuations due to adjustments in ventilation controls occur more often during the mining process. Atmospheric conditions and barometric pressures can generate fluctuations in mine pressure on a large scale. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Investigations conducted in coal mines in the United States, Australia, Poland, and South Africa observed higher methane emissions from the gob during periods of falling atmospheric pressures, which led to mine explosions (McIntosh, 1957; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Belle, 2014; Wasilewski, 2014; Lolon et al., 2015). Falling external pressures are understood to cause potential outflow of explosive mixtures from the gob, while rising pressures may push fresh air into the gob. This phenomenon is widely known as gob breathing. The actual processes that trigger gob breathing are not fully understood, nor are the parameters that contribute to the process. Other major events such as roof falls or fan failures can also change the pressure conditions in the mine. In contrast to atmospheric pressure changes, these events can change mine pressures much more rapidly or immediately. TIME LAG AND GOB BREATHING CONCEPT In a bleeder ventilation system, the pressure in the gob is designed to be lower than that of the headgate entries and the longwall face. Air from the gob and gate entries flows towards the tailgate-bleeder returns. When the external pressures are disturbed, this designed pressure arrangement may change, potentially resulting in increased outflow from or inflow into the gob."

Jan 1, 2017

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene, plagioclase feldspar, and pyroxene which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals as well as reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilise the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. Reducing chromite recovery is of critical importance since high levels may negatively affect the downstream smelting process. Chromite recoveries can however be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. In summary, due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator, and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible.

By Lottrey A. L, Sowerby B. D, Cutmore N. G

On-line monitoring of low rank coal quality during input to a process has the potential to provide benefits through: ò anticipation of coal quality variations prior to utilisation; ò provision of a tool to help determine the influence of coal quality on process behaviour, and ò provide a direct measure of coal quality for pricing. Moisture and ash are the two most significant coal quality parameters for combustion. They determine the energy content which can be derived from the coal and the problems arising from the presence of ash in the process (eg ash fouling, corrosion, erosion, particulate emissions and ash disposal). Extensive pilot-scale testing and full-scale experience has shown that specific coal/ash constituents (eg Na2O/ash ratio, acid-soluble aluminium, silica, sulphur contents, etc) are also important for the behaviour of Latrobe Valley brown coal during combustion, ash formation, deposition and removal of ash in precipitators and furnace ash hoppers. This paper discusses the range of on-line analysis techniques which have been investigated and their application to low rank coal analysis. Preliminary results from a joint SECV/CSIRO project which aims to develop two separate advanced instrument systems are also presented. These systems are based on: ò microwave attenuation and phase shift - for direct determination of moisture content; and ò inelastic neutron scattering - to provide total hydrogen, carbon, chlorine and ash contents, with potential for calculation of moisture content, specific energy, sodium content and Na20/ash ratio using correlations.

Jan 1, 1992

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

By Krishna Parameswaran

This paper discusses sustainability considerations in primary copper smelting using selected examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission definition of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper mining and smelting practices can be made sustainable. The examples used to illustrate sustainability considerations include: (1) adoption of flash smelting; (2) emission reduction and process improvement associated with anode refining of blister copper and the converter retrofit project, and (3) preliminary research findings on alkali treatment of copper smelting slags and copper mine tailings.

By Jr. Harty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tonnage of our steel by from 60 to 80 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores Which has been made available by the bureau's ore-dressing studies, combined with the products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements when manganese-silicon alloys and ordinary Spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromanganese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores. This paper resents the results of work done under a cooperative agreement between the Pittsburgh Experiment Station of the United States Bureau of Mines and the Carnegie Institute of Technology, the Metallurgical Advisory Board, and the University of Pittsburgh, Pittsburgh, Pa.; between the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.; between the North Central Experiment Station of the United States Bureau of Mines and the University of Minnesota, Minneapolis, Minn.; and between the Rare and Precious Metals Experiment Station of the United States Bureau of Mines and the University of Nevada, Reno, Nev.

Jan 1, 1931

By J. Kretschmann

Mining heritage can be of outstanding value for many regions around the world, because mining has been done for thousands of years for the benefit of mankind and its development. This paper presents an ongoing project creating a general guideline for the handling of mining heritage on the basis of experiences made in Germany. Interactions of stakeholders in the ?heritage network? as well as strategies for the technical proceeding will be described. An action plan for the sustainable handling of mining heritage has already been developed in part, which includes necessary measures. Best-practice recommendations will be derived. Keywords: m ining heritage / preservation / guidelines / action plan / Sustainability

Feb 27, 2013

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

This brief introduction tries to introduce delegates to this conference to the almost unbelievable attributes possessed by many microbes which might be relevant to geomicrobiology, and how most of these remain unexploited by us. It introduces some of the terminology which will be used and tries to suggest that there are rewarding times for those who set out to discover the natural biodiversity of bacteria in nature. Although we have exploited microbes, usually unwittingly, and suffered at their hands for millennia, it is only recently that we have begun to become aware of how they dominate our planet (most of the earthÆs biomass is bacterial) and are responsible consequently for most of what happens here. A few can cause us harm and occasionally kill us, but most bacteria are beneficial, impacting positively for example on how we grow our food and in cleaning up the pollution we create. They are simply indispensable to how we live. They have been responsible for many of the geochemical changes which have taken place on this planet and play major roles in the transformation of elements so essential to our existence (Newman and Banfield, 2002). No one should dismiss them as minor players in our game of life.

Jan 1, 2004

By G. L. Ploetz

The lanthanon compounds are becoming increasingly more important for ceramic and allied applications. As the supply increases and the cost decreases, further development of these interesting materials will undoubtedly lead to new applications and an increased demand. Recent improvements in separation processes have lead to high purity in the individual lanthanon oxides. This report includes short discussions on the mineralogy of the ores as raw materials, and on the separation processes required to produce the pure individual lanthanon oxides in useful quantities. To discuss the presently known applications of lanthanon oxides, this general review is divided into the following categories: A. Glasses, Glazes, and Porcelain Enamels. B. Refractories and Abrasives. C. Electronic Ceramics. D. Nuclear Ceramics.

Jan 1, 1960

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By Ashish Kumar Vishwakarma, Vivek Kumar Himanshu, Kaushik Dey

The accurate prediction of blast-induced ground vibration due to underground ring blasting is a prominent need for ensuring the safety of structures. Different site-specific empirical equations are available for the prediction of ground vibration. These empirical equations are best suited when the monitoring and blasting locations are present in the same medium. The change in the medium alters the behavior of wave propagation. Hence, existing empirical equations have limitations in peak particle velocity (PPV) prediction when the blasting location is an underground hard rock mine and the monitoring location is ground surface. This is because the underground metal mine comprises different levels having void in the form of excavated stope or paste-filled stope. It is very difficult to predict the magnitude of PPV on the surface in such instances. Therefore, this study has been carried out to predict the PPV at surface due to underground blasting. In this paper, PPV data was recorded at surface for 207-ring blasts. Furthermore, the PPV has also been measured at different underground locations for 47-ring blasts. Different empirical equations along with k-nearest neighbor (KNN) and random forest (RF) model of machine learning technique were developed for the prediction of PPV. Most of the empirical models have higher accuracy in the prediction of PPV at an underground location. This shows that scaled distance-based empirical predictors are best suited when the monitoring and blasting media are the same. However, the empirical models do not predict PPV accurately when the monitoring location is ground surface and the blast is conducted underground. The machine learning models are better suited for PPV prediction in such cases. Based on the analysis performed for the case study site, RF model predicts PPV at surface with the highest accuracy. The coefficient of determination and root mean square error for RF model used for predicting PPV at ground surface are 0.94 and 0.438 mm/s respectively. The RF-based model is also the best suited among all the models for predicting PPV at underground locations as well.

Apr 20, 2024

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971