Search Documents

By G. M. Brownell

Introduction Within the past year a new deposit of gypsum has been opened up and brought into production in the Province of Manitoba. Until 1930, Manitoba's entire production came from Gypsumville, northwest of Winnipeg, at mile 161 on the Gypsumville branch of the Canadian National railway. However, during 1930 a gypsum bed was opened up at a point one mile south of the village of Amaranth, forty miles north of Portage la Paririe, on the west side of lake Manitoba (See Figure 1). Although no exposure has yet been discovered, the presence of gypsum below the surface in that district has been known for many years as the result of drilling for water. In 1929, J. R. Spear (1), of Winnipeg, interested some local capital in the possibility of .finding commercial deposits of gypsum, and, after some exploration work in the area with a well drill, the Amaranth deposit was located. Sixteen holes were put down at intervals of 400 or 500 feet, all of which encountered what appeared to be a continuous bed of gypsum, about thirty-eight feet thick, at a depth of 92 feet. The extent of the deposit has not yet been determined.

Jan 1, 1931

By Richard E. Hucko

The Coal Preparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals--an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal--to establish grade- recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes--nominal minus 35 mesh (0.5 mm) and nominal minus 100 mesh (0.149 mm)--and subjected to conventional froth flotation. The froth product was then beneficiated by coal-pyrite flotation or HCMS to provide a direct technical comparison of the two processes. At minus 35 mesh (0.5 mm), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a size of minus 100 mesh (0.149 mm) , however, the performance of HGMS exceeded that of coal- pyrite flotation. The separations effected by HGMS were more efficient at minus 100 mesh (0.149 mm) than at minus 35 mesh (0.5 mm). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size, or the process has not been optimized to treat material finer than 35 mesh (0.5 mm).

Jan 1, 1981

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By W. Vickers

SALKOVITZ1 has given a number of useful angles between planes for use with the Laue method in determining the orientation of bismuth single crystals. Bismuth is usually considered as having a face-centered-rhombohedra1 structure with its axial angle 87°34', Fig. 1. A similar figure given by Sal-kovitz appears to be in error in that the angle there marked as 87°34' should be 92°26. The primitive cell is a single rhombohedron of axial angle 570 14. The structure is almost face-centered-cubic and hence high accuracy in measurements is essential if there is to be no confusion in indexing poles or zone axes. It is easier to get this accuracy if zone axes are plotted on the stereogram because they will lie near the basic circle where the net has a more open scale. The zone axes can be read from the film, using a Greninger chart, and can be plotted more accurately than poles. Also, the angles between points near the basic circle can be read more accurately than those between poles near the center. In order to use the zone axes the angles between directions have been calculated from a formula given by Niggli,2 and are given in Table I. Miller indices

Jan 1, 1958

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By Virgil J. Stachura, Calvin L. Cumerlato

The U. S. Bureau of Mines is conducting research on blasting methods that reduce highwall overbreak and the associated rockfall hazards. This paper presents the results of tests using a low-density water gel to improve the quality of air-decked presplit blasts at a surface coal mine in New Mexico. The explosive's specific gravity averaged 0.50 and was bulk loaded using a modified truck which injected the gassing agent. Reductions in overbreak and resulting rockfall were achieved in comparison to a highwall presplit with ANFO. The test sections used 15° angled blast holes and resulted in 1,119 m (3,672 ft) of air deck presplit highwall using a low-density water gel which was then compared to 894 m (2,934 ft) of highwall shot with an ANFO air decked presplit design. The total quantity of explosives per hole ranged from 68 to 113 kg (150 to 250 lbs) and the 27 cm (10-5/8in) holes were 19- to 33-m (62- to 108-ft) deep on 5.5 m (18-ft) centers. Periodic visual examination and photographic surveys of the highwall test areas were used to document the amount of rockfall. In addition, laser profiles of selected sections were conducted to further delineate the damage and highwall contour differences.

Jan 1, 1995

By Michael Gauna

An evaluation and analysis of a coal pillar bump in a West Virginia mine indicated that the pillar bump occurred because of the unique combination of controlling factors. The pillar?s development stability factor of 2.6, based on Mark-Bieniawski strength and tributary loading, would typically indicate an adequate pillar size for long-term main entries. A combination of multiple-seam mining geometry and geological conditions resulted in stress concentration leading to the coal pillar bump. No high extraction mining had been performed in the area and the overlying works appeared to have adequate stability factors. However, it was interpreted that long-term flooding had softened the overlying pillar system and rendered all but the largest pillars ineffective. Contributing factors include large overlying pillars transmitting stress through the approximately 60 ft of interburden and the failed pillar?s location at a transition in the immediate roof from shale to hard, massive sandstone. Other contributing factors include sandstone channeling forcing the development section to mine the pillar smaller than surrounding pillars in an attempt to avoid the channel, the relatively high overburden of 1,100 ft, and the pillar?s position in the bottom of a trough within the coal horizon. Pillars subjected to similar conditions on the other side of the section did not fail where the roof was composed of shale, even though the roof exhibited evidence of high stress concentration. An analysis was undertaken to determine appropriate pillar size for future mining. The conditions were evaluated by investigating mine historical conditions, assessing pillar bearing pressures, and using Lamodel 2D coupled with traditional Mark-Bieniawski pillar strength and tributary area loading stability factors to determine the stress levels for the pillar. Recommendations for future pillar sizes were based on the critical load bearing capacity identified by the analysis. To date, no further pillar bumps have occurred.

Jan 1, 2008

By J Jones, J Blunt

"The requirement for environmental approvals and associated environmental impact assessments (EIAs) is now commonly regarded as a key milestone and body of work during project development. EIAs can be undertaken at various phases during project development, generally either:\ during the scoping or prefeasibility studies, where limited project information is available and the mitigation and management measures of the EIA become a set of criteria and commitments that control project design during the feasibility study, as an iterative approach whereby mitigation and management measures are developed through an integrated process with the engineering team, and measures are included in the feasibility study cost model following the feasibility study, where detailed project design information is available, the cost model is complete, and the EIA is an assessment of a fixed project with limited opportunities for mitigation and management measures to be integrated into engineering design. This paper investigates the advantages of integrating EIA into life-of-mine planning during the feasibility study phase, using the Tampakan Copper-Gold Project (the Project) as a case study. The Tampakan Project is located in the Philippines on the southern island of Mindanao. The Project involves the proposed development of three main areas of infrastructure:a large-scale, open pit copper-gold mine and associated mine site infrastructure (including tailings and mine waste storages, fresh water dam, concentrator, etc) a power station, port and filter plant (PPFP), located approximately 60 km from the mine a pipeline and transmission line linking the mine and PPFP sites.Examples of engineering measures developed through an iterative process to mitigate and manage predicted environmental and social impacts include design of water management infrastructure, modification of the disturbance footprint (eg roads realigned to avoid critical habitat) and realignment of project infrastructure to minimise impacted water catchments.CITATION:Blunt, J and Jones, J, 2012. Integrating environmental impact assessment into life-of-mine planning, in Proceedings Life-of-Mine 2012 , pp 143-152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By S. R. McCutcheon, D. R. Lentz

"Abstract - The 12.1 Mt Brunswick No. 6 Zn-Pb-Cu-Ag massive sulfide deposit (New Brunswick, Canada) lies between two subaqueous felsic volcanic formations near the base of the Middle Ordovician Tetagouche Group. The footwall comprises rhyodacitic pyroclastic rocks (Nepisiguit Falls Formation), whereas the hanging wall comprises a sequence of rhyolitic flows, breccias, and hyaloclastites (Flat Landing Brook Formation), with an age difference of less than 3 m.y. The Brunswick No. 6 deposit is a proximal autochthonous deposit with a well-zoned massive sulfide body and a basal Cu zone that, at depth, develops into a stockwork stringer sulfide (feeder) system. The massive sulfides are capped sharply by a layered magnetite-chert unit that extends regionally beyond the deposit. The deposit has a keel shape (sheath) formed by the F1F2 interference pattern. The heterogeneous ductile deformation and upper greenschist-grade regional metamorphism has transposed many of the epigenetic stockwork structures and alteration within the host sequence. Hydrothermal alteration is much more extensive, both vertically and laterally, in the footwall (a few 100 m) than in the hanging wall (<100 m). Anomalies farther up in the hanging wall sequence seem to be associated with independent alteration systems related to the rhyolite domes. The least-altered footwall units exhibit keratophyric alteration (albite or adularia) and weak Mg enrichment (chlorite). More intense micaceous (sericite and Mg-rich chlorite) alteration occurs around the footwall sequence. The transposed stockwork stringer sulfides are typically composed of Fe-rich chlorite (± sericite, ± silica) with pyrite, pyrrhotite, chalcopyrite, arsenopyrite, and sphalerite. The (Fe2O3T+MgO)/(Na2O+K2O) and base metal alteration indices are the best practical lithogeochemical vectoring tools at this deposit. Sommaire - Le gîte de 12.1 Mt de sulfures massifs de Zn-Pb-Cu-Ag Brunswick No.6 est localisé entre deux formations volcaniques felsiques sous-marines situées près de la base du Groupe de Tetagouche d’âge Ordovicien Moyen. Le mur consiste en roches pyroclastiques rhyodacitiques (Formation de Nepisiguit Falls) tandis que le toit consiste en une séquence de coulées, de brèches et d’hyaloclastites de composition rhyolitique (Formation de Flat Landing Brook); la différence d’âge entre les deux est de moins de 3 m.y. Le gisement Brunswick No. 6 est un gîte autochtone proximal comprenant un corps de sulfures massifs clairement zoné ainsi qu’une zone cuprifère basale qui passe progressivement à un stockwork de filonnets de sulfure en profondeur (feeder). Les sulfures massifs sont abruptement surmontés d’une unité laminaire de chert et de magnétite dont l’extension par delà le gisement est régionale. Le gisement affecte la forme d’une quille (fourreau) résultant d’un patron d’interférence F1F2. Plusieurs des structures épigénétiques du stockwork et des patrons d’altération de l’encaissant ont été transposés par la déformation ductile hétérogène ainsi que par le métamorphisme régional au faciès des schistes verts. L’altération hydrothermale est beaucoup plus importante, tant verticalement qu’horizontalement, dans le mur (quelques 100 m) que dans le toit (<100 m). Les anomalies situées plus haut dans le mur semblent être reliées à des systèmes d’altération indépendants associés aux dômes de rhyolite. Les unités les moins altérées du mur une altération kératophyrique (en albite ou en adulaire) ainsi qu’un faible enrichissement en Mg (chlorite). Une altération en mica (séricite et chlorite magnésienne) plus intense est présente autour de la séquence du mur. Les sulfures du stockwork de filonnets transposés consistent typiquement en chlorite ferrifère (± séricite, ± silice) accompagnée de pyrite, de pyrrhotite, de chalcopyrite, d’arsénopyrite et de sphalérite. L’indice d’altération (Fe2O3T+MgO)/(Na2O+K2O) et l’indice des métaux usuels sont les outils d’exploration les plus appropriés dans ce gisement."

Jan 1, 2006

By Oleg B. Girin, Yuliya O. Proshenko

"Several approaches to electrolytic synthesis of new types of composite coatings with improved properties were devised using the authors' findings on development of texture, substructure and structural state in metal electrocrystallization. Addressed are texturally composite coatings having improved resistance to wear and corrosion; substructurally composite coatings having improved hardness and corrosion resistance; phase-change constitutionally composite coatings having improved corrosion resistance, reflectance, hardness and resistance to wear; structure-change constitutionally composite coatings having improved electric and magnetic properties; restricted-substructure composite coatings having improved resistance to abrasive-impact wear; and modified-substructure composite coatings having improved strength and plasticity.IntroductionIn recent years, some trends in the formation behavior of crystal texture, crystal substructure and structural state of electroplates were revealed and effects of texture, substructure and structural type on electroplate properties were discovered (1-3). Our interest was in using these findings and effects to develop some ways of synthesizing new types of composite electrolyte coatings having enhanced properties."

Jan 1, 1998

By John P. Harmon

Vehicles traveling on untreated dirt and gravel roads at open-pit mines disseminate high concentrations of dust (fig. 1). Excessive dust creates safety hazards by reducing visibility and may endanger the health of the men who breathe it. If the dust contains free silica, it can cause silicosis. In addition, maintenance costs of mechanical equipment are increased if equipment is operated in extremely dusty places. Dust on haulage roads in hot, arid country can be controlled if the surface of the road is sprinkled frequently and adequately with water. Often, when roads are sprinkled with water to control the dust, hazards are caused through reduced traction and skidding because of the mud that is formed on the surface of the road. Reducing the amount of water used will help to reduce the hazard of skidding.

Jan 1, 1957

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual&apos; usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system&apos;s performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By J. M. Floyd

Technology in use commercially and available for commercialisation for injection processing of base and precious metals in bath reactors is surveyed and compared. Differences between bath smelting and suspension smelting systems are highlighted in relation to important smelting criteria. The factors affecting the results achievable with various tuyere and lance injection bath smelting systems are discussed in relation to the various smelting, converting and refining operations involved in copper, nickel and precious metal processing steps. Process chemistry, process dynamics and heat and mass transfer rates are discussed for the different systems.

Jan 1, 1993

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981

By K. Hodgson, Cook. N. G. W.

Most structures are designed so that the possibility of failure is eliminated. However, some degree of failure in the rock around deep mine excavations is inevitable if mining operations are continued. The presence of failed rock constitutes a hazard the magnitude of which can be predicted by computer models from calculations of the energy change per unit area mined in stopes, or the field stress around service excavations. Empirical relationships between these calculable quantities and the incidence of rock failures and delays associated with them have been established. Experiments on the computer using different layouts enable the mining engineer to select the least hazardous of otherwise acceptable alternatives, and to predict the incidence of damage ahead of actual mining, so that appropriate measures to maintain an adequate degree of safety and productivity can be planned in advance.

Jan 1, 2014

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By Dixon CA

In the early 1970s, Jim Walter Resources, Inc. (JWR) embarked on a coal mine expansion program that was unparalleled in the history of the United States. With a small nucleus of people then operating two rapidly depleting captive mines, action was initiated to develop four of the deepest mines in the United States. Because of the depth of these mines, operational and technical problems were anticipated. However, because of the high quality of the coal (Blue Creek Seam), the financial risks involved were acceptable. The total investment to get the expansion program completed (to get the new mines to full capacity) would represent an investment of over US$ 500 million.By the end of the decade of the 1970s, the Company had grown to 2100 employees who were producing 1640,000 tonne of saleable coal per year, a productivity rate of 3.9 tonne per man-shift. This productivity rate was not sufficient to maintain a profitable, viable organisation. Therefore, if the operations were going to survive, it would be necessary to improve productivity tremendously, a task which would tax the resources and imagination of all employees.

Jan 1, 1991