Search Documents

By L. M. Dwarkin

Strip mining in Western Canada, though of considerable importance, is a fairly recent development for many of the operators in the district. Adding to the difficulty of unfamiliarity is the fact that a great deal of the stripping is done on pitching seams, for which the engineering and economic principles of setting the most advantageous strip ratio are not readily apparent. The novelty of the operation combined with the complexity of the principles involved can easily lead to misconceptions as to the determination of the economic ratio. Definition of Strip Ration There are two commonly accepted meanings of the term strip ratio: (1) The ratio of feet of overburden to be stripped per foot of coal recoverable. (2) The ratio of cubic yards of overburden per cubic yard or ton of coal. The first definition is inapplicable to pitching seams so, throughout this paper, strip ratio will be taken as the ratio of cubic yards of overburden to be removed per cubic yard of coal recoverable. Economic Ratio In the case of flat seams, the strip ratio is fixed by existing natural conditions, and the magnitude of this ratio determines whether stripping is economically feasible. With pitching seams, however, the strip ratio is a variable. On the outcrop, there is usually some coal which can be obtained with little or no stripping. As the work is carried down the pitch of the coal seam, the proportion of overburden continually increases until a point is reached where it is no longer economical to continue the operation. The question immediately arises as to the location of this point, and this resolves into the problem of determining the most favourable strip ratio, or, to use the accepted term, the economic ratio.

Jan 1, 1949

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By M. H. Ali

Codelco, a multi-process primary copper producer, is undertaking a full life cycle inventory (LCI) of all its commercial products based on copper and molybdenum. During this work, many questions have surfaced regarding the contribution of process unit design to specific aspects of a product's LCI and, more importantly, how such designs could be improved using a life cycle perspective. Management strategy efforts were undertaken to improve the LCI footprint, however it was found that the corrective actions were almost impossible to apply at the operation level in plant, given the ongoing timing pressures of extractive mining, and costs saving priorities. Additionally, it was found that most of the important comparative differences between operations had structural reasons. In this circumstance, the LCI practitioner group from 1M2, and the environmental managers from Codelco, decided to shift its efforts to place the critical LC1 aspects to the design process of future developments. Hatch Associates has developed unique tools in their Sustainable Plant Design (SPD) package that compliment and enhance LCA methods; these effectively drive sustainability into the heart of the design process. By using LCA and SPD in a project design phase, you cannot only address potential hotspots, but also decide on materials, location and size of certain facilities to optimize for energy efficiency. Moreover, you can avoid the shifting of environmental burdens upstream or downstream within the plant and finally it is extremely useful in identifying opportunities for greenhouse gas reduction.

Jan 1, 2007

By B. McFadzean, M. Tadie, T. Dzingai, M. Becker

Ores from a single deposit may exhibit extensive variability in their mineralogy and texture. The ability to quantify this variability and link it to mineral processing performance is one of the primary goals of process mineralogy. This study focuses on the effect of alteration in three platinum group element ore samples from the Great Dyke in Zimbabwe – two of which were more pristine compared to the third, which was locally classified as ‘oxidized’ ore. These ores are known to be characterized by varying degrees of alteration, resulting in numerous challenges in flotation and affecting both grade and recovery. Alteration, by near-surface oxidation, of the valuable base metal sulphides and platinum group minerals resulted in lower flotation recoveries of Cu, Ni, Pt, and Pd. Evidence of incipient oxidation was more readily observed in the base metal sulphide assemblage than the platinum group mineral assemblage, even though the loss in recovery (because of oxidation) was most significant for Pd. Alteration through hydration resulted in a significant increase in mass pull and dilution of concentrate grade through the inadvertent recovery of naturally floating gangue comprising composite orthopyroxene and talc particles. In this study, the amount of naturally floating gangue was more strongly correlated with the talc grain size distribution than the grade of talc in the flotation feed. The oxidation and hydration alteration reactions are not necessarily mutually exclusive, although one may be more dominant than the other, giving rise to ore variability.

Sep 1, 2021

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965

By Sigurd L. Lamhauge, Karl Gunnar Holter, Svein E. Kristiansen

An innovative sprayable waterproofing membrane in combination with the traditional Nordic method of waterproofing with polyethylene foam sheets was used for the waterproofing of the tunnel. The sprayable membrane was integrated in the final sprayed concrete lining in a sandwich structure, hence constituting a composite water-proof lining based on sprayed concrete. The spray able membrane was applied in areas with small to moderate water ingresses, making up approximately 50% of the total area requiring waterproofing in the tunnel. State-of-the-art application technology with a computerized spraying robot was used. A consistent application of the required thickness at a high speed was thereby achieved.

Jan 1, 2007

By J. E. Pogue

It is the purpose of this paper to attempt to establish three theses which may be stated in advance as follows: 1. The crude oil potential is the accumulation of surplus initial production. 2. The crude oil potential is a semi-inventory and therefore is a causal factor in the price of crude petroleum. 3. The price of crude petroleum no longer correlates with above-ground inventories but does correlate with corrected inventories (i. e., above-ground storage plus the inventory equivalent of the crude oil potential). The factors and principles set forth in this study are thought to yield an approximate answer to a number of questions of active interest in the petroleum industry today, to wit: (a) How long would be required to eliminate the potential if all drilling ceased? (b) What would be the indicated crude oil production of the United States in 1931 if proration were abandoned? (c) What economic change would be necessary to warrant a higher price for crude oil? Definitions For the purposes of this study the following definitions may be stated: The crude oil potential in the United States is the quantity of oil that all the oil wells would make the first 24 hr. if permitted to flow unrestricted. The surplus potential is the above-mentioned quantity minus the volume currently produced. Initial production is the first day's unrestricted flow of an oil well. Aggregate initial production is the sum of the initials of all wells completed during a year. Surplus initial is the initial not needed to bring production into balance with demand. The surplus initial is equal to the crude oil potential minus the current rate of production. The annual production-equivalent of the crude oil potential is the volume of oil that would be produced in one year if all wells were permitted

Jan 1, 1931

By A. D. Ramirez, L. E. Gutierrez, M. A. Garces

"Scarcity of freshwater in mining operations in arid zones in different parts of the world has led to the mining companies to think about using seawater as an alternative source in mineral processing operations. Examples of this situation are Minera Centinela (AMSA) and Minera Sierra Gorda (KGHM), both plants located in northern Chile. Previous studies showed that molybdenite flotation is depressed at high pH values in seawater as a result of the action of hydroxy-complexes of magnesium and calcium that attach to the faces of the molybdenite particles, reducing its hydrophobicity and as a result flotation recovery. In this work, a study of the interactions between molybdenite and kaolinite is presented. The effect of sodium hexametaphosphate (SHMP) dispersant on the recovery of molybdenite in the presence of kaolinite is studied in different aqueous media and it is correlated with induction time data. The results allow to conclude that kaolinite has a stronger depressing effect on molybdenite in seawater compared to its effect in freshwater. Magnesium and calcium are the cations that have the strongest effect in enhancing the interactions between molybdenite and kaolinite. SHMP reduces the negative effect of kaolinite on the floatability of molybdenite both in seawater and freshwater. The induction time data correlate well with the micro-flotation results.INTRODUCTION The need for water in mining processes in arid and semi-arid zones has led to the search for new alternatives for this resource, among which seawater has gained an important space. In Chile, most of the mining operations are located in the northern part of the country, an area that has limited availability of freshwater for the processing of copper and molybdenum sulfides (Castro and Laskowski, 2011, Castro et al., 2012 a). Seawater is an aqueous solution with high concentrations of ions such as Na+, K+, Mg2+, Ca2+, So42-, Cl-, and other less concentrated species which generate important effects in the flotation process as they modify the properties of the solid/liquid, and liquid/gas interfaces, and also increase the consumption of some important reagents used to depress pyrite such as lime. It has also been proposed that flotation of copper sulfides is negatively affected in seawater because of the reduction of oxygen solubility compared to freshwater (Millero et al., 2002; Duan and Sun, 2003). In contrast, it has been shown that the presence of ions in solution in the process of flotation of natural hydrophobic resources improve recovery as result of the compression of the electric double layer (Laskowski, 1974; Klassen and Mokrousov, 1963, Laskowski and Castro, 2008."

Jan 1, 2018

By Akhila Manne, Prasad P. V S R

Storage tanks are heavily loaded thin-shelled structures that exert large loads on and require large foundations to support them. They are generally very sensitive to foundation settlements as it may hinder the performance of tanks resulting in significant commercial or social impacts. Selection of their foundation is dependent on availability of suitable ground and limitations imposed by design specifications. Design of the tank foundations is generally based on theoretical methods and validation by representative field tests. This paper reviews settlement criteria for storage tanks as per national and international standards, case studies of large to medium diameter tanks supported on deep foundation i.e., bored cast-in-situ piles and shallow foundations on improved ground and their performance during load tests & hydro-tests is discussed. Paper concludes that storage tanks can also be supported on shallow foundations resting on improved ground reducing the settlement, time and cost significantly depending on the sub-soil.

Nov 1, 2022

The high maintenance of load-haul-dumps (LHDs) and front end loaders in hard rock affects mine planning with reduced availability and productivity. Intensive study of maintenance costs and availability of machines related to machine age and life provide the basis for planning from available operational alternatives.Derived programmes and experiences have led to the beginnings of unmanned operation and automation through reduction of manual diesel units and spreading electrification and use of radio. But electrification has obvious layout limitations. This approach to the present has resulted in better utilisation, costs and safety and the computerised monitoring and control provides continuous awareness of machine and work conditions with the promise of future improvements.

Jan 1, 1991

By Wu Aixiang, Zhou Qian, Zhou Zaibo, Liu Juanhong, Wang Hongjiang

To improve the pumping capacity and engineering efficiency of fresh thickened tailings slurry, a high charge density superplasticizer was developed to improve the rheological properties of tailings slurry. The effects of superplasticizer content, the concentration and fineness of tailings, the proportion and type of cementitious materials, temperature, and hydration time on the rheological properties of unclassified tailings slurry and backfill materials were studied. The variation characteristics of the slurry yield stress, plastic viscosity, and thixotropy with different factors were measured by a Brookfield R/S-SST plus rheometer. The experimental results of fresh thickened tailings illustrated that the higher the concentration of the slurry and the finer the tailings, the worse the rheological properties of the slurry. The results of cemented paste backfill materials indicated that the rheological parameters increased as binder content and time increased. The rheological parameters decreased as the temperature increased. The addition of a superplasticizer reduced the rheological parameters and improved the rheological behavior of the fresh thickened tailings and cemented paste backfill materials, which was beneficial to the slurry’s pipeline transportation. This paper can provide technical guidance for slurry transportation in the backfill system and provide a reference for designing the superplasticizer used in tailings.

Jan 5, 2022

By Oliver Bowles

DISCUSSIONS of trade and commerce are generally more comprehensive today than in the past; the problems are approached with a vision unrestricted by national boundaries, and broad enough to comprise the entire world. The extent to which the limited viewpoint that has characterized past ages is yielding to an economy of world-wide scope is exemplified by the Atlantic Charter which blazes a trail in the direction of trade principles that aim to preserve the interest of each individual country in the commonwealth of nations. Its fourth article promulgated the principle that all nations should have access on equal terms to the trade and to the raw materials of the world which may be needed for their economic prosperity. Future developments in reciprocal international trade may have some effect upon the flow of nonmetallic minerals but such effects are not likely to be great because tariffs and trade policies have not affected that flow profoundly in the past. Nevertheless conditions may change and new problems may arise demanding important decisions. Sudden changes are not to be expected, but rather an orderly evolution in which national interests will merit due consideration in establishing broader policies.

Jan 1, 1945

By B. A. Strathdee

An arsenical ore containing both pyrite and arsenopyrite was heated to a temperature at which decomposition and distillation took place. The condensate consisted of metallic arsenic and arsenic disulphide, although the analysis of the ore showed that volatile arsenic and sulphur were present in proportion to produce a condensate of arsenic trisulphide and sulphur. Distillation tests on the mineral arsenopyrite also produced a condensate of metallic arsenic and arsenic disulphide. This arsenic sulphide gave a distinct x-ray diffraction pattern which was not listed in the A.S.T.M. data file. This same sulphide can be produced by heating a mixture of arsenic and sulphur in vacuo. Its chemical analysis corresponds to As2S2. The dissociation pressures of arsenopyrite and the vapour pressures of arsenic disulphide and arsenic metal were measured, using a quartz "spoon" gauge. The dissociation pressures of arsenopyrite were compared with the published data for the dissociation pressures of pyrite to account

Jan 1, 1961

By J. R. Linney

THE Eastern magnetite industry has not failed in its contribution to the war program during the past year. Man-power shortage was the critical problem in maintaining production and for the last half of the year, owing to lack of man power, it was necessary for some mines to change from seven to six days per week schedule. At Cornwall, Pa., the mine operated by the Bethlehem Steel Co. produced approximately 2,000,000 tons of crude ore and 1,200,000 tons of iron ore concentrates, a decrease of about 10 per-cent compared with the previous year. Railroad haulage in the open-pit at this mine was discontinued, being replaced by Mack trucks of approximately 30 tons' capacity. At the Mt. Hope mine in New Jersey, the Warren Foundry and Pipe Corp. produced about 195,000 long tons of crude ore obtaining 70.000 long tons of lump ore and 35,800 long tons of concentrates. An additional 24,500 long tons of concentrates was produced from a stock pile of 47.000 long tons of crude ore accumulated during the latter half of 1943, following the fire in their old dry mill. All of this material was handled through their Brown

Jan 1, 1945

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992

By John A. Hudson, Xia-Ting Feng, Joseph S. Y. Wang

Evolution over decades and progress over last five years have been made in many topics of interests to rock mechanics, geosciences, physics, and multi-disciplinary interactions in underground research laboratories and development facilities, as well as in underground energy recoveries and environmental assessments. Rock mechanics and geotechnical engineering advances are associated with quantifications of disturbed/damaged zones and rock alternation and bursting processes and creation of underground spaces and accesses associated with deepening of shafts and lengthening of tunnels. Geophysics and earth sciences advances are associated with continuing collections of seismic, electromagnetic, and gravitational data and conducting various thermal, hydrological, mechanical, chemical, and biological investigations, both separately, simultaneously, and in different coupled ways. Astroparticle and underground physics advances are associated with many long term experiments to detect rare events and needs for increasing larger and deeper halls to accommodate next generation detectors, shielings, and isolations. There are also increasing interesting in underground settings to explore multidisciplinary and inter-disciplinary sciences and technologies. Energy and environmental sciences and assessments have evolved from traditional oil and gas focuses to recent activities associated with green resources and alternative recovery/disposal strategies. The evolution and progress of these interdependent and related fields are discussed in this quadrennial Congress.

Jan 1, 2015

By R. T. Artz

Disposal of sewage is an important part of mine sanitation. Improper... handling and.disposing of sewagerare conducive to the spread of disease and often add foul and nauseating odors to the mine air. The diseases spread by unsafe methods of disposing of waste in mines are typhoid fever, cholera, amebic dysentery, hookworm, and other intestinal diseases due to parasites. Sanitary toilet facilities, with a good sewage-disposal system, each maintained in good order at all times, should help to prevent the spread of diseases transmitted by intestinal body wastos. The metal and nonmetal-mining industries have recognized the impor-dma tance and need for disposing sewage properly; accordingly, facilities of some sort are installed and need today in most large mines. The coal-mining industry has given little thought to the disposal of sewage underground; however, in most mines of the anthracite industry, the inflow of large vol- unes of highly acid mine water and the extensive drainage system required to remove this water provide a natural means for disposing of sewage.

Dec 1, 1946

By John T. Eastlick

The Banner mining district is about 70 miles northeast of Tucson in the southern part of Gila County, Arizona. Production from the district, valued at about $26 million, is chiefly from copper-silver-lead zinc ores. The stratigraphic section consists of Precambrian conglomerates, quartzites, dolomites, and limestones, Cambrian quartzites; Devonian limestones; dolomites, and shales; Mississippian limestones; Pennsylvanian limestones and shales; and Cretaceous volcanic and sedimentary rocks. Deformation of these rocks presumably started near the end of the Cretaceous, and extended into the late Tertiary. The sedimentary rocks were folded, faulted, and intruded by fine grained diorite, quartz mica diorite, and dacite porphyry. At least four distinct stages of mineralization are recognized. In the first stage of contact metamorphism and the second stage of hydrothermal alteration, favorable zones were prepared for ore deposition. Metallization occurred in three of the mineralizing stages. Magnetite, pyrite, and hematite were deposited near the end of the second stage of hydrothermal alteration. The third stage included the main deposition of sphalerite, chalcopyrite, bornite, and galena. In the fourth and final stage, minor amounts of sulfide minerals were deposited with a late anhydrite and quartz gangue. The ore deposits in the form of veins and veinlets, pipes, irregular massive replacements, and bedded replacements are localized by the extent and distribution of metamorphic and hydrothermal alteration, by the proximity to the intrusive contacts, and by the effects of structural development. Oxidized ores of copper, lead, and zinc constituted the principal production of the district prior to 1940, but, for the most part, supergene enrichment was of minor economic importance. The ore bodies of the district are in the mesothermal class of deposits, occurring as normal metasomatic replacement and vein types.

Jan 1, 1968

By G. S. Rice

To those concerned in attaining greater safety to life and incidentally to property in coal mining, the meeting of representatives of the national mine safety research organiza¬ tions of the principal coal-producing countries, which was called by the Safety in Mines Research Board of Great Britain at its experimental station near Buxton, should have deep significance. It is notable, first, because it meant the friendly cooperation of countries not many years ago engaged on either side in the great World War; and second, because of the remarkable degree of agreement in the essential fundamental factors and methods of attaining greater safety in coal mines when it is considered that the questions were approached by different paths and that the applications dealt with widely differing natural conditions and national points of view. Varying views, of course, were held as to the relative importance of certain factors, but the differences were of detail rather than of principle. When the meeting adjourned it was unanimously agreed that such meetings should be continued annually and that the greatest benefit was to be derived by close cooperation in the exchange of data. Belgium, France, Germany, Great Britain, and the United States were represented by one or several members of the respective national research organization. It is of interest to note that this research work in Belgium, France, and Germany is supported directly by na¬ tional organizations of mine operators or owners but placed under a scientist appointed by the respective Government, thus giving the work official standing. In Great Britain the work is carried on by a Government board, consisting of persons connected with the coal¬ mining industry or in mining research, appointed by the Secretary for Mines, to direct the work of research of the Mines Department. It does not, however, come under its inspection service. Its work is supported by a penny-a-ton tax on output of coal. In the United States the mine-safety research work is directly supported by the Federal Government.

Dec 1, 1932

By P. G. Barnard

The Bureau of Mines investigated the effects of various additions of rare-earth metals or rare-earth oxides on the mechanical properties of cast and wrought plain-carbon steels. Rare-earth metals, as misch metal, were added to medium-carbon steel in amounts to 0.70 weight-percent; rare-earth oxides, as a commercial mixture, were added in amounts to 1.50 weight-percent. The melting and casting of conditioned steels were done in a vacuum-induction furnace, to avoid formation of oxides from the melting atmosphere and to pro-vide better control over chemical composition. At room temperature, data for tensile strength, yield strength, elongation, and hardness of cast and wrought steels were obtained by standard testing equipment and procedures. Impact tests were conducted on as-cast steel specimens. The greatest amount of tensile ductility and impact strength was obtained in as-cast steel with 0.50 to 0.70 weight-percent misch metal additions. No significant improvement on mechanical properties was indicated in wrought steels containing rare-earth metal additions in the range from 0.10 to 0.70 weight-percent. In general, the rare-earth oxide additions up to 1.50 weight-percent had little effect on the tensile properties of steel in the cast, wrought and annealed, or wrought and normalized condition.

Jan 1, 1967