Search Documents

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

Jan 1, 1920

By AIME AIME

THE Petroleum Division opened its proceedings on Wednesday morning, with two simultaneous sessions on engineering and economics. The first paper at the engineering session, over which A. W. Ambrose presided, was "Underground Surveys of Oil Wells," by Alexander Anderson of Los Angeles, Calif., was presented by John Suman of the Humble Oil & Refining Co., Houston, Texas. Following this, the paper of E.'H. Griswold of the Mailand Oil Co., Houston, Texas, was presented by C. V. Millikan of the Amerada Petroleum Corp., Tulsa, Oklahoma. Following the presentation of these two interesting papers a general discussion followed on the subject of "Crooked Holes." The discussion was entered into by F. H. Lahee, Sun Oil Co., Dallas, Texas;'Messrs. Bigelow of Tulsa, H. W. Hixon of New York City, Van Court Warren of Los Anyeles, Calif; H. L. Wheeler of St. Louis, Mo.; R. R. Brandenthaler, United States Bureau of Mines, Bartlesville, Okla.; H. H. Riggs, Indiana Territory Illuminating Oil Co., Bartlesville, Okla.; C. V. Millikan and John R. Suman

Jan 1, 1929

By Guohui Zheng

The ever increasing quantities of solid wastes generated by various industries are at the source of the growing need for proper waste disposal methods. Thermal treatment of combustible wastes is a proven technology which permits the reduction of hazardous material having to be landfilled. However, this method is not universally applicable to waste disposal. For example, the transferal of heavy toxic metals into the thermal remediation products is a major issue of public concern. This paper focuses on the analysis of morphology changes from solid sludge to ash which is a product of the sludge combustion. The morphological parameters analyzed were particle size and external surface. They were determined using Jeol 840 Super Probe. The experiments were conducted in a computer-controlled high-temperature combustion system consisting of the thermogravimetric furnace coupled with Fourier transform infrared spectrometer (TGA-FTIR). Sludge particles were made of complex fibers trapped in the aluminosilicate matrix. At low temperatures, up to 680 K, the solid residue looked similar to the initial sludge. Between 680 K and 1180 K the sludge underwent intensive burning and steadily changed into powdered ash. At the temperature of 1050 K the ash was composed of separate, flat flakes with sizes ranging from 5 to 20 um. At 1470 K the flakes aggregated into large particles. The surface observed at 1670 K was a mixture of mullite crystals. Such structure could result from the solidification of the ash material after its melting. Morphological changes influenced the distribution of metals in the solid residue. For example, Cr was concentrated in small aggregates. Such distribution should allow for recovery of valuable metals from the solid waste residue.

Jan 1, 1996

By A. Pandey

Over the years, Coal Beneficiation at Tata Steel - West Bokaro has seen varied changes. With increasing R.O.M throughputs & lowering of the concentrate ash, Fine Coal Beneficiation process has thrown up myriad challenges. Development of Synthetic Collector was initiated couple of years back with Technical assistance from NLC Nalco India Ltd. Coal from West Bokaro unit was sent to Nalco?s Naperville (US) research lab for developing Tailor made synthetic collector . After comprehensive lab flotation studies, synthetic collector was developed & recommended for plant evaluation. The lab scale results were very promising in terms of improved separation efficiency & yield at similar ash level. The collector sample received from Nalco research laboratory were revalidated at Nalco Kolkata lab and finally at Tata Steel West Bokaro lab, confirming the promising results. (S.E 25-30 % better than HS Diesel) The key factors playing out for this improvement initiative are a) Scope for improvement in Clean Coal Yield at same or lower ash level coupled with improved Selectivity and Separation Efficiency b) Introduction of a Synthetic Collector with a Green Chemistry and subsequent replacement of H S Diesel, which is highly inflammable with a less inflammable & safer product Trial was conducted at plant scale in two phases and comparative performance of the Collector vis-à-vis Diesel was evaluated across the following Coal Seams of Q- SE (Seam VII, VIII, VI, IX and X). The results generated are very promising and the improvements observed are summarized below. ? Separation efficiency improvement by more than 20% observed. ? Flotation Fines yield increase varied from 0.6- 1.5 % on raw coal basis across different seams. ? Consumption pattern is 20-25 % lower than Diesel. Keywords: synthetic collector, west bokaro, coal beneficiation, HSD

Sep 1, 2012

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls. Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By V. P. Bhavanandan, S. B. Dubbs

The mucus secreted in the respiratory tract provides the first barrier against inhaled particulate and gaseous toxicants. The major component of mucus which is responsible for the physical properties and protective functions of the respiratory mucus is mucin. We have initiated investigations to determine the effects of coal mine dust on the synthesis of respiratory mucin by rat trachea under in vitro and in vivo conditions. In this study we have established optimum conditions-:ro-r~ the asceptic growth and mucin secretion of rat tracheal explants in culture. The best outgrowth of ciliated epithelial cells and maximum mucin production was obtained in CMRL 1066 medium containing 10% fetal calf serum. The explants continued to secrete mucin even after three weeks in culture. For the estimation and characterization of mucins the tracheae were cultured in the presence of [3H] glucosamine and [35S] sulfate or [14C]leucine. The mucins were isolated from the medium by gel filtration, treatment with hyaluronidase, ion exchange chromatography and CsBr density gradient centrifugation. Precipitation of polyanionic material in the culture media with cetyl pyridinium chloride and fractional extraction with NaCl also yielded mucin free of glycosaminoglycans, but in low yields. The tritium label in the purified mucin was distributed in sialic acid (50%) galactosamine (37%) and glucosamaine (13%). The density of purified mucin as determined by CsBr gradient centrifugation was about l.43g per ml in comparison to l.46g per ml for human respiratory mucin with a carbohydrate content of about 80% by weight. Alkaline borohydride treatment released saccharides which contained about 80% of the radioactivity. The effect of adding varying amounts of coal dust to the culture medium is under investigation. (Supported by U.S. Bureau of Mines Grant G1135142, Project 4210).

Jan 1, 1989

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By More-O&apos, R. C. Ferrall, J. W. Wilson

Discussion: M. D. G. Salamon* (Fellow): The theoretical principles behind the techniques of calculation used by the authors was formulated and published during the period 1962- 65. These principles, together with their practical implications, were summarized in a review paper in 1966.1 Now, in February, 1970, we have this long and comprehensive paper discussing the practical application of the theory. I think this is good progress. The large number of practical examples treated in the paper clearly demonstrates not only the skill and knowledge of the authors, but also the versatility of the techniques of analysis. I feel that the techniques described by the authors, and their improved versions, will revolutionize mine planning. I suggest that no shaft system or stoping layout should be planned in future without an adequate rock mechanics analysis. It seems that it will be progressively more difficult to white wash mistakes in rock mechanics and attribute their costly outcome to normal mining risk. We should not, however, become complacent. There is still a lot to learn and do in the future. I do not want to discuss tonight the question of further research but instead, I will raise two other problems which may hinder the future progress of practical rock mechanics. To carry out work similar to that described in the paper, mine managements require men who are capable of doing the work and who have the most efficient techniques of analysis at their disposal. As a research engineer I have been associated with the development of techniques of analysis. I can assure you that these have undergone an amazingly rapid development during the last six years. We have seen the change from the use of the electrolytic tank analogue and manual integration to the method described by the authors, that is, to the employment of the automatic network analogue and computer integration. But this is not the end. In a recent paper Prof R. P. Plewman2 and his co-authors described a completely digital technique. Here the process of calculating on- and off-reef quantities is integrated into one computer run. But these sophisticated methods of computation are useless without men to make intelligent use of them. During the last few years a new breed of mining engineers has appeared on the scene - the Rock Mechanics Engineer. I feel it is timely to call the attention of the senior members of this Institute to the fact that this new breed will succeed in carrying out its duties in a valuable manner only if we manage to attract to its ranks young engineers of the right quality. The requirements are high. The top rock mechanics engineers have to be good mine planners and they have to understand the essence of sophisticated theories. Without these attributes they will not succeed in the long term and the industry will not gain the benefit of available knowledge. To attract this quality of engineers the industry will have to ensure that rock mechanics is accepted by all concerned as a career which could lead to the top echelons of our profession. Finally, I would like to make one or two remarks concerning Part I of the paper. In Sections 3.1 and 3.2 the authors describe methods of determining the normal stress on the reef plane and the convergence distribution in the excavations. The description as given applies only to a horizontal reef. When the reef is inclined the situation is more complex since a shear component of stress on the intact reef and a ride component in the excavations must then also be determined. These can be calculated by methods similar to that described in the paper.3 The practical application of the method of calculating the released energy (Section 3.4) is in the comparison of various stoping layouts to establish an order of preference in terms of decreasing rates of energy release. To carry out these comparisons effectively, the calculations must be carried out in a manner by which the values of energy per unit area obtained are comparable. I would like to note in this respect that the method of calculation given in the paper is valid without reservation only if there is no elastic contact between the hanging and foot walls in the mined-out area. If there is contact then the calculated energy values are correct only if the mined out area is increased in small steps during the analysis. My second point in this regard is concerned with the practical method of calculation as described in Sections 3.4 (ii)-(iii). Firstly, I would like to suggest that the energy calculation should be carried out, as far as possible, by using always the same scale on the analogue. Secondly, the reading of current on a pin should be followed by the removal of that pin to obtain the corresponding reading of potential. The product of these two values will be proportional to the energy released during the mining of the small area corresponding to that pin. The method suggested by the authors tends to mask possible danger points in the layouts, since they obtain an average value for a time period, say, for six months.

By M. Jiang, X. Fan, W. X. Chen, Z. K. Guo, H. H. Zou

"Some improvements are carried out for elasto-plastic model by taking the shear dilation effects and relaxation effects of deep rocks into accounted. The high pressure equations of states with Mie-Grüneisen form are also introduced to describe the relation of pressure-volumetric strain. Numerical simulations of free field responses for deep underground explosions are conducted by using the user subroutines which compiled by means of the secondary development functions of LS-DYNA9703D codes. It is indicated that the dynamic responses of free field are well simulated based on this improved elasto-plastic model, and the analytical results are in good agreement with the data of U.S. Hardhat nuclear test.INTRODUCTIONDynamic behaviors of deep rocks for underground explosions are obviously different from that of shallow underground explosions and have aroused great attentions of international experts who work for rock engineering. The dynamic models of deep rocks could be roughly divided into classic elasto-plastic model and fracture damage model according to different theoretical foundation. M. E.Kipp and D. E.Grady et al. are the outstanding representatives who engaged in the researches of fracture damage mechanics. Researches of dynamic problems for geomaterials were carried out by C.C.Grigorian and the conclusion that incompressible elasto-plastic medium model could not be used to solve the problems of closed underground explosion was derived, and therefore C.C.Grigorian model was proposed. In this model, C.C.Grigorian assumed that the average hydrostatic pressures and the densities of medium had one to one relationship, and the path of loading or unloading is different from each other. For shear deformations, analytical solutions of the problems were derived according to the model which was slightly different from Prandtl-Reuss model, the constitutive equations were closed by Mises-Schleiher constitutive model. However, the analysis showed that there were two inadequacies in C.C.Grigorian model. Firstly, the shear dilation effects of fractured medium after wave front could not be considered. Secondly, the relaxation characteristics of the rocks in fractured region were not taken into account."

Jan 1, 2015

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

By G. K. Wilson

This paper will discuss some of the more important aspects to be considered when selecting pumps for mill discharge, cyclone feed or other severe-duty applications Included will be the selection of the pump based on such factors as particle size, particle distribution, head, flow, temperature and pH Other specifics to be covered: The relationship of impeller speed, head and wear factors as they affect pump performance and wear life; the importance of selecting a pump whose performance curve best suits the application; and how the addition of service factors applied to the actual operating conditions can lead to severe operational problems such as premature wear, pump running out on curve, and exceeding horse power limitations.

Jan 1, 1996

By G. Ellie, D. F. Coates

"The mining of coal in thick and inclined seams is difficult, and there are only a few countries in the world that are really interested in the problems associated with their exploitation. In France a considerable amount of investment has been made in the mechanization of systems appropriate for such conditions.For seams inclined up to 50 degrees, of normal thickness, a new system was introduced in 1967. It consists of a longwall advancing to the rise with walking props, a shearer and hydraulic backfill. During the first two years the panel productivity was an average of 25 TN/MS, and they foresee the possibility of reaching an average of 30 TN/MS.A system for thick beds, both horizontal and inclined, is in p•rocess of being mechanized. In 1969 they started with a method consisting of a longwall in a footwall slice, or sub-level drifts with walking props, and caving and drawing up to a height of 20 m of coal. Recent experiments with a shearer have produced panel productivities between 9 and 11 TN /MS, and there is hope that with experience an average of 16 TN/MS will be obtained.In 1964 a method was initiated for beds inclined from 60 to 90 degrees, based on a mechanical cutter designed by the collieries in Lorraine. An overhand slice of 4.2 m in height is taken with a drum cutter mounted on the end of a boom. Hydraulic fill is placed at the completion of a slice. The face productivity, which has been from 13-20 TN /MS, can be perhaps increased to an average of 22 TN/MS. For those companies with important reserves in inclined and thick seams, these French systems may be worth the trouble of examining in some detail."

Jan 1, 1972

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Rob Scott

Making a difference with Zinc & Health Two billion people do not get enough zinc in their diets. Every year 450,000 children die from complications arising from zinc deficiency Our Zinc Alliance For Child Health partnership with CIDA and Micronutrient Initiative, our involvement with UNICEF through the IZA and our partnership with BASF are gaining wide recognition. Sustainability at Teck ? Integrating into our Core Business Strategy Our strategy Long term goals Our approach Managing risks and finding opportunities Our progress Early reports Moving Forward Metrics and indicators

May 1, 2013

By Kilmar Mine

The Kilmar dolomitic magnesite deposit~ in sourhwesr Quebec lie in Grenville Province sedimentary rocks that strike north and dip steeply west. The sediments comprise quartzitic, carbonate and argillaceous members. The middle or carbonate member hosts the magnesite and, like the two other members, has been intensely mewmorphosed. Magnesite occurs as lenticular shaped zones of altered limestone and is mixed with 5 to 30% dolomite crystals. Diopside, serpentine and mica are common accessory minerals. Magnesite appears to have formed from merasomarism of all or part of the carbonate member due to intrusion of hot magnesia-rich solutions. Magnesite is mined from a 490 m vertical shaf1 and is milled and burned into clinkers, which then are shipped 10 pyroprocessing industries around the world.

Jan 1, 1984

By F. Moraw

The use of redox fuel cells in which oxygen is replaced by other oxidants such as ferric ions can have significant advantages [1-3]. For example, the cathodic reaction rate (e.g., exchange current density) can be increased by several orders of magnitude compared to the oxygen reduction reaction, and platinum group metal (PGM) catalysts are not required. As a result of the higher aqueous solubility of the oxidant in a redox fuel cell compared to that of oxygen the rate of mass transfer (e.g., limiting current density) is greater by several orders of magnitude. The redox fuel cell can achieve high efficiencies and has other fuel cell advantages. The main issue with the redox fuel cell cathode is the regeneration of the oxidant where low conversion efficiencies are achieved even with platinum group metal (PGM) catalysts. In the work discussed here the Fe3+/Fe2+ redox fuel cell cathode is characterized over a range of electrolyte concentrations and operating conditions, and electrode materials. Cyclic voltammetry and electrochemical impedance spectroscopy are mainly used for electrochemical characterization and mechanistic determination of the cathode redox couple. Further characterization with selected compositions and materials is done in a redox fuel cell (hydrogen - Fe3+/Fe2+). The mechanism and the advantages and disadvantages of the fuel cell redox cathode are discussed with respect to other approaches and other redox couples.

Jan 1, 2005

By Dennis R. Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson’s effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.