Search Documents

By Dong-dong Liu, Jian-ping Niu, Qi Liu, Shu-sen Cheng

A numerical model was developed to simulate the three-dimensional heat transfer in the belly and lower shaft region of the blast furnace wall consisting of copper steel composite stave, packing and shell. The temperature distribution of copper steel composite stave without the slag layer or refractory lining was investigated and then compared with the copper stave. The results showed that copper steel composite stave can satisfy the requirement of overheatingfree and had an analogous heat transfer behavior as copper stave but more stable cooling intensity. This model had been validated by the good agreement between the computed and measured temperature in the thermal test.

Jan 1, 2015

By Joseph B. Umpleby

PROGRESS in the petroleum industry in 1929 has been characterized by outstanding accomplishments in the fields of new discovery of supply, economic control of production, increased efficiency and reduced costs of recovery, and lowered costs and greater flexibility in manufacture. Resources have been developed in an outstanding degree in the Kettleman Hills. California, the Oklahoma City field (which adds a large potential area in central Oklahoma), the discovery of Woodbine sand production in East Texas, and the discovery of Wilcox sand production in west-central Kansas. Engineering technique has progressed both along the lines of development and production, with a net result that costs have been reduced and extraction increased in notable degree, although it is impossible to give a close measure of either. In the field of re- fining crude oils variations to the end of promoting reduced cost and greater flexibility has been more important than genera! acceptance of innovations in practice.

Jan 1, 1930

By J. Keough

During industrial electrowinning of copper, uneven growth can impact current efficiency, cause short-circuits in the cell and negatively impact the final quality of the metal product. Copper electrodeposits can be made smoother by incorporating a host of additives in the electrolyte but uneven copper growth may still occur due to variations in electrolyte composition throughout the cell-house. To quantify roughness, 3D images of the surface may be combined with scaling analysis to gain further insight into the deposit structure. Moreover, scaling analysis may offer a method to predict long-term deposit structure using short-term copper deposits. In this paper, the application of Atomic Force Microscopy (AFM) and scaling analysis are used to monitor copper growth and extract surface roughness characteristics. The cathode was a 304 stainless steel disc that was polished to a mirror finish. Copper was deposited onto this surface over a range of 10, 20 and 30 minutes from an acidic sulfate solution (40 g/L Cu) at 40oC from an electrolyte that contained or was free of guar. AFM images were acquired to obtain 3D topographical information on the samples and scaling analysis was performed to extract the root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. INTRODUCTION During the process of copper electrowinning, the dissolved metal ions are reduced and thereby deposited onto a cathode substrate which is later recovered by stripping the metal from the cathode surface. Although this process is widely used in the industry, the conditions of the deposition procedure may cause the growth of the metal product to be uneven which can not only impact the current efficiency and final copper product quality but may also lead to plant interruptions through short-circuits if the anode and cathode make contact. To create more uniform copper deposits, a host of additives may be included in the electrolyte which may act as brighteners, leveling agents and inhibitors which may include guar gum, glue, thiourea or polysaccharides or polyacrylamides and their industrial use has changed over time (Moats, Luyima, & Cui, 2015). As such, the electrolyte composition is often complex and subtle variations in the solution matrix throughout the cell-house may impact the surface morphology of the final copper product. In an effort to quantify the roughness of copper samples, image analysis is often applied and may include Scanning Electron Microscopy (SEM) or Atomic Force Microscopy characterization. While both are appropriate, AFM offers 3-dimensional information which may be used to both qualitatively and quantitatively characterize the surface characteristics.

Jan 1, 2019

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By A. Rajan

"Drawing upon the experiences of a gold extraction plant startup in the Southern Pacific, this paper will describe the importance of the commissioning phases to the project outcomes to achieve early target production despite an overall time compression to attain full plant production. Some of the highlights of the paper include: impact of roles played by the Owner’s construction and operations representatives during project commissioning, the formation of a capable and competent “Mod Squad,” availability of trained operating personnel, control over work priorities and the scope of work needed to bring the plant to safe initial operations. The commissioning team comprised subject matter experts skilled in process technology supported by “generalists” thoroughly conversant in overall plant operations. The merits of a structured team approach to brainstorm and resolve commissioning challenges as opposed to direction from individual subject matter experts is discussed. IntroductionStartup or commissioning is a unique period in the life of a project. Each stage of a project-exploration, feasibility, design, construction, commissioning, initial operations and continuing operations-requires special talents, know-how, and practices. Each stage makes particular demands of the people involved. Initial operations are no exception.Having experienced the 1997 startup phases of oxide and sulfide facilities for a gold extraction plant at a remote island in the Southern Pacific, I can attest to the many challenges and rewards. Commissioning for both facilities was extremely successful and brought the entire project on line well ahead of the targeted completion dates. Using this specific project as an example, this paper will highlight some of the key features of project commissioning. In this paper, the term “pre-commissioning” denotes all activities that lead to mechanical completion; “commissioning” occurs when feed is introduced; and “initial operations” are defined as the duration when operations accepts the system/facility and takes over."

Jan 1, 2000

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By Russell R. Trengove

Bureau of Mines exploration at the property of the Tulare County Tungsten Mines was by core drilling from the surface from May 16, 1950, to July 13, 1950. The property is in the western foothills of the Sierra Nevada Range, 18 miles northeast of Lindsay, Calif. It has been in almost continuous production since 1942 and has produced 40,831 units of tungsten trioxide (W03) with a grade of approximately 67 percent. The work performed comprised a study of the geology, mapping the area, sampling the outcrops, and diamond drilling the area adjacent to the mine workings. Ten holes were drilled for a total of 1,824 feet. Ore reserves were found to be confined to tactite zones in a surface area approximately 250 by 400 feet and extending downward about 350 feet.

Jan 1, 1956

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1966-67. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By Akihide Nagao

The behavior of impurity hydrogen that is contained in starting material or picked up during processing has been little investigated up to now. The hydrogen microprint technique is applied to determine the microscopic location of impurity hydrogen during deformation in aluminum without hydrogen charging. Three kinds of pure aluminum of 99.99% are prepared, in which hydrogen content is varied by changing the atmosphere when they are melted and heat-treated. After rolling, tensile specimens with a gage size of 4 x 4 rnm and 0.5 mm in thickness are stamped out from these three kinds of aluminum sheets. These specimens are covered with a liquid nuclear emulsion of silver bromide crystals, stretched by 5,10 and 15 percent plastic strain or fractured, developed and fixed. SEM micrographs reveal a number of silver particles on the slip lines and on the grain boundaries. Also shown is that the more hydrogen present in the specimen, the more silver grains appear on the slip limes and on the grain boundaries. Consequently, it is concluded that impurity hydrogen is transported to the surface with gliding dislocations during deformation.

Jan 1, 1998

By Hao Zhang, Mi Zhou, Lichun Jiang, Xihong Zhang

This study investigates the roof stability of underground limestone mining in the presence of stratified joints during the excavation process. An analytical solution is derived to predict the stresses and deformation of underground tunnel structures, with the structure simplified as a double-hinge arch. The accuracy of the analytical model is validated through comparison with finite element modeling results. A parametric study is then conducted to assess the influence of different design parameters on the optimization of tunnel stability during excavation. The results indicate that the best stability of the tunnel can be achieved in engineering practices when the applied load (q) is 5 MPa and the joint inclination angle (θ) is 45°, with the roof span and thickness set at either 12 m and 8 m or 15 m and 10 m. These findings provide valuable design guidance for underground limestone mines with stratified joints.

Oct 18, 2023

By Wang Dawan

During the process of arsenic bearing gold concentration biooxidation, the content of chloride ion in water is a very important factor to the activity of bacteria and the oxidation of sulfide minerals. In this paper, the influence of underground mine water with different chloride ion content to the biooxidation of arsenic bearing gold concentration and the limit of chloride ion content to bacteria were summarized. These results indicated if the content of chloride ion was less than 1.2g/L, the bacteria?s ability to oxidize sulfide minerals was little affected, and if the content of chloride ion were increased to 2g/L or more, the activity of bacteria was seriously restrained, and if the content of chloride ion were increased to 4g/L, the activity of bacteria was absolutely restrained. So, as the content of chloride ion in water was cumulated to 2g/L or more in biooxidation plant, the water must be refreshed to maintain normal production.

Jan 1, 2008

By N. Seidle

Numerous studies conducted in the 1960's and 1970's concluded or implied (1) that a high accident rate in terms of severity and frequency exists among new (first year) operators of mine machinery equipment, and (2) that lack of experience and training is a major cause of this high accident rate. Further studies refined this premise to show that the major causes of accidents among first year operators are: (1) lack of manipulative skills; (2) failure to follow/adhere to routine procedures; and (3) failure to recognize and respond properly to hazards. This report describes the design, development, and manufacture of a shuttle car operator training system, including a program of instruction which: ? Is economically feasible. ? Addresses accident data and specific causes of accidents. ? Includes an aerospace quality simulator of sufficient fidelity to teach and develop manipulative skills, recognition of and response to hazards, and routine and emergency procedures. ? Is designed to significantly reduce the severity and frequency of accidents especially during the operator's first year. ? Is designed to significantly improve the performance of the trainee as compared to the standard learning curve. Development of the simulator produced several valuable by-products including a major state-of-the-art technological advance in visual systems for simulators, and a first-time application of (certain) advanced filming techniques to underground filming.

Jan 1, 1984

By H. R. Pierce

Bureau of Mines engineers end others have endeavored to deter-nine a fundamental method for gauging the capacity of gas wells to deliver gas under different pressure conditions. Their studies show that for accurate gauging two factors must be determined: (1) The actual pressures at the face of the sand in the well (usually referred to as "at the sand"), acid (2) the relation between such pressures and the rates. of flow of c as through the sand. This paper, the first of a series, describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the well head.

Jan 1, 1929

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

Single-unit separations in mineral processing are typically not able to meet the strict purity requirements for consumer markets. As a result, multistage separation circuits are often employed. Because these circuits represent a large and inflexible capital investment, process engineers are careful to ensure that the circuit is optimally designed to meet the desired objectives. The set of interdependent decisions that constitute the circuit design may involve the selection of different unit operations, different equipment specifications, different operational parameters, and different unit interconnections. To assist circuit designers in assessing these options, researchers have attempted to establish standard design methodologies that involve various techniques and tools.

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written which aid in the design process in the academic arena and should also have industrial applications. The programs described include a dragline cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program and an overburden volume and coal tonnage sequencing program.

Jan 1, 1985