Search Documents

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By H. M. Shepard

THE copper industry operated at high capacity throughout 1947, with no serious tie-ups in operation as was the case in 1946, when almost the entire industry was shut down by a four-month strike. Refined copper production in the United States averaged 94,250 tons for the first eleven months and deliveries to domestic consumers, including foreign copper for domestic consumption, averaged 114,000 tons per month. On April 29 the import duty of 4d per lb was suspended until March 31, 1949. Copper prices fluctuated considerably for a short time thereafter. Over the year the price of domestic electrolytic copper at refineries on the Atlantic seaboard advanced from 19.225¢ on Jan. 2 to 21.200d on Dec. 24.

Jan 1, 1948

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By James W. Guider

Of all the technology available to the iron blast furnace operator, raw materials preparation [(Fig. 1)] is by far the most important. Superior raw materials have been basic to the success of the Japanese steel industry, and they are just as essential to the American steel industry in winning its competitive battle against foreign government subsidized steel imports. Therefore, the mine operator and the ore beneficiation engineer must strive to produce the highest quality raw materials possible to meet the precise demands of the modem blast furnace and steel plant.

Jan 1, 1982

By K. Tobór-Osadnik, M. Wyganowska, A. Manowska

"The behaviour of employees is an essential issue in the field of occupational health and safety. Safe behaviour is to a large extent determined by, apart from motivation and preventive actions, an employee’s attitude towards hazard. Thus, attention should be given to defining employees’ attitudes, and following that, to the possibility of correcting and shaping these attitudes in relation to hazard and obeying occupational health and safety regulations. The authors have focused on the analysis of employee attitudes to health and safety regulations in Polish coal mining companies, taking into consideration earlier research on the behaviour of selected employees. The paper presents the methods used to identify Z-type (passive) behaviour. Next, this behaviour is analysed to identify differences between a Z-type employee (enslaved) and other employees. To conclude, the paper presents a list of possible motivational tools that may be used to encourage occupational health and safety in Z-type employees. IntroductionThe technical state of equipment and conditions in the workplace greatly influence occupational safety. However, the deciding factor influencing the rate of accidents in the workplace is the frequency with which employees practise risky behaviour. Factors such as the social conditioning of conduct and motivation for organizing safe work conditions have been included in the notion of creating a positive culture of work safety. This notion has been approved as one of the main goals in management (Studenski, 1996).Safe behaviour is to a large extent, apart from motivation and preventive actions, determined by an employee’s attitude towards hazard. All actions undertaken in the field of occupational health and safety, including training, motivational systems, or imitation of behaviour resulting from a high culture of occupational safety in a given work environment, will not bring about the desire effects if workers have an inappropriate attitude towards occupational health and safety regulations."

Jan 1, 2017

By J. P. F. Charpin

The transport of large boulders in a furrow from a mining area to a nearby pond was considered. The furrow is filled with a mixture of water and soil particles flowing down to the pond at high velocity. Due to operating constraints, the slope of the furrow is reduced progressively. A relationship is derived, relating the slope of the furrow and the composition of the fluid to the maximum size and shape of the transported boulders. The characteristics of the boulders carried all the way down to the pond may then be determined.

Jan 1, 2007

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By R. D. Leitch, J. G. Calverley

"INTRODUCTION Although many investigators have provided information on the strength and other properties of concrete the published literature cites few data on the effect of mixing cement with acid mine waters or on acid resistance of concrete in contact with mine waters. Most of the reported work on the effect of impure waters has dealt with the resistance of cement specimens to ""sulfate waters,"" that is, waters or soils with a relatively high sodium sulfate content. The ""Merriman test"" is used commonly to determine the corrosion resistance of cements for 28 days, but it does not seem certain that a cement having a high sulfate resistance in the Merriman or similar tests necessarily will show correspondingly great resistance to the sulfates of iron and, particularly, to sulfuric acid, which usually are present in acid mine waters. Extensive use of cement mortar for laying up masonry stoppings in coal and other mines and for constructing concrete mine haulageways and shaft linings, coal-storage and other retaining walls, highway bridges, culverts, and many other types of construction where it is difficult to obtain fresh water for mixing or where the structures are later exposed to contact with acid waters makes it important to know the effect of these conditions on cement and whether there is a cement better suited for such work than ordinary portland cement.CONDUCT OF THE INVESTIGATIONFor a short time early in 1935 the opportunity to obtain at least some additional information on the effect of acid mine water on cements was presented by the Relief Works Division, which provided money for irregular and indefinite employment for several months. Purchase of apparatus or material was not permitted under this arrangement, and indefinite duration of the work, intermittent employment, and finally complete cessation of the work prevented planning for extensive investigation of this particular problem."

Jan 1, 1940

By G. Geremia, M. I. Serrano, L. Costa, Strohaecker

The advances in electronics and the development of more efficient algorithms, allow for the designing of more complex and sophisticated automated systems. The new devices include lighter, faster, reliable, and stronger robot manipulators. One available technology, with relatively low cost, is a simple robot manipulator controlled by remote control. The device has been designed to be used in both mining and law enforcement, where it can be useful for inspection, rescue, gas analysis, and even to manipulate dangerous objects, such as explosives. The applications may even include the rescue of trapped miners in risky environments. The major advantage is the fact that the robot can be controlled with a remote and monitored through a video camera, minimizing human exposure to hazardous areas, where robots can perform tasks in an aggressive atmosphere and confined spaces. This article presents a mining robot manipulator controlled by remote control, using video cameras for positioning and sensors for movements, which are located on the operator's arm. With this system, it is possible to create a sensation of virtual reality, allowing easy operation for anyone trained in dealing with explosives, rescues, or other dangerous tasks. Blasting and mining are becoming perfect applications for robots, and its use should increase very soon. The results are discussed and presented for the brand new Xiru 01 robot manipulator.

Jan 1, 2010

By A. Abdollahi

Modification of the silicon in Al-Si alloys can be performed by adding a very small amount of some elements like Na, Sr and Ca to alter the form of silicon from an acicular shape to a fine fibrous one. This modification results in a considerable improvement in mechanical properties especially elongation, Metallographic observations in A356 alloy indicated the degree of the modification with Na, Sr and Ca, They showed that the effect of Ca as a modifier is not as strong as is Na or Sr while Na is the most effective modifier, Although modifiers improve mechanical properties, they also increase porosity in castings, The reduced pressure test (RPT) and Tatur test showed that the increasing porosity with Na is the most and with Sr is the least.

Jan 1, 2004

By Charles W. Henderson

THE influence of mineral production on the development of the western United States has been profound. From 1848 to 1860, there was only gold production, the effect of silver began in 1860, and from then on both had a powerful influence. Lead production started in 1863, copper in 1863, and zinc in 1885, but was small until 1898. Gold alone was therefore the stimulus of the early settlement and exploration of the Western States.. But mineral deposits caused neither acquisition of territory nor determination of boundary lines. Arizona, California, Nevada, New Mexico, and parts of Utah, Wyoming, and Colorado were formally acquired from Mexico fourteen days after the actual date of the discovery (January 19, 1848)1.2 of gold at Sutters Mill, near the present town of Coloma, California (a discovery which, with the immediate new discoveries, aroused the world several months later) ; but the acquisition was by treaty (under negotiation for some time but signed February 2, 1848)3 in settlement of a war involving the boundaries of the grassy plains of Texas, an area at that time not known to contain any metals, and to date found to have but few metal deposits.4 The international boundary at 49º latitude for the far northwest states was determined by causes other than mineral deposits.

Jan 1, 1933

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By A. C. Johnstone

The aim of the study is to determine if pit lakes are a sustainable coal mine closure option in South African. The water balance, chemistry, limnology, and bacterial population of three selected pit lakes were investigated. The lakes are in the three major coal basins of South Africa and are associated with different lithologies and mining methods. The major factors driving the water balance of the pit lakes are direct rainfall, runoff, inflow from old mine workings, and groundwater infiltration, with the major losses being evaporation or discharge onto surface. The study indicated that pit lakes can be designed as ’terminal sinks’ to provide a sustainable mine closure option. The pit lakes sampled have an alkaline pH, and mostly a sodium/calcium sulphate water with total dissolved solids content of less than 3000 mg/l. The phytoplankton and microbiological data indicates that the pit lakes support aquatic life. The study shows that correctly designed pit lakes can be an environmentally sustainable closure option for South Africa’s coal mines. A suggested design manual has been developed to assist mine owners and regulators in developing sustainable coal mine pit lakes as a closure option.

Oct 1, 2021

By AIME AIME

THE No. 9 mine of the Wheeling & Lake Erie Coal Mining Co., a subsidiary of M. A. Hanna & Co., at Fairpoint, Ohio, has normally produced about 1000 tons of coal daily for several years, but recently it was converted into an experimental mine to afford means of studying new methods and equipment under consideration for development and mining. Among other projects, the possibility of using a duck-bill, self- loading conveyor in driving entries, with a view of in- creasing the rate of progress where quick development is of importance was studied. Actual operation soon revealed that even though break-throughs are made ,every 60 ft., as required by the state mining laws, the :amount of natural Ventilation reaching the working face was not sufficient to supply the men and that in ,order to obtain a plentiful supply of pure. air and maximum efficiency and to avoid costly interruptions after shots, it was necessary to supply auxiliary ventilation by using Ventube and a Vano fan.

Jan 1, 1929

By E Baafi, G Brassington

Coal mining operations can impact on various types of surface infrastructure or natural features, including cliff-lines, steep slopes and natural watercourses. Longwall mining leads to a subsidence depression due to the changing geometry of the mined out area. The current regulatory process for managing subsidence in New South Wales (NSW) involves the preparation of a Subsidence Management Plan (SMP). This paper demonstrates the use of a Weights of Evidence (WofE) technique applied within a Geographical Information Systems (GIS) environment to predict potential areas for rockfalls along cliff-lines in the NSW Southern Coalfield. The WofE is a ædata-drivenÆ method that can be used to predict subsidence impacts prior to mining. The WofE method was applied to ten known rockfalls along the Cataract River to evaluate the reduced impact of not mining within 50 m of cliff-lines along the Nepean River. There is significant reduction of probabilities of rockfall occurrence when mining is avoided within 50 m of cliffs.

Jan 1, 2006

By F. S. Knoll

Electrostatic separation is one of the most misunderstood physical processes used to beneficiate minerals. Nonetheless, millions of tons of titanium ores, iron ores and other minerals are processed every year economically, efficiently and safely. Over the past ten years major advances in electrostatic separation and its application have occurred. New processes include dewatering clay slurries, separating halite and sylvite, and shape separation of vermiculite and gangue minerals. Electrostatic separation techniques are based on one of two methods, electrophoresis or dieleccrophoresis -- processes involving charged and uncharged particles respectively. In some cases, the combination of these two techniques has proven quite useful. The purpose of this paper is to provide a basic understanding of the physical processes collectively called "electro- static separation" in order to enhance one's ability to define and consider new possibilities in mineral processing and other fields.

Jan 1, 1984

By W. C. Maurer

A drilling-rate formula for roller-cone bits is derived from rock crater-ing mechanisms. This formula holds for "perfect cleaning", which is defined as the condition where all of the rock debris is removed between tooth impacts. Under these conditions, the drilling rate is directly proportional to the rotary speed and to the bit weight squared, and inversely proportional to the bit diameter squared and to the rock strength squared. Under imperfect cleaning conditions, such m those usually present in field drilling, re-grinding of the cuttings occurs under the bit, and the drilling rates fall below those for perfect cleaning. INTRODUCTION Drilling with a roller-cone bit consists of two fundamental operations: the formation of craters under the bit teeth, and the removal of the broken rock from the craters. To delineate the mechanisms of drilling, it is first necessary to understand the mechanisms involved in the formation of individual craters and then to relate these mechanisms to the over-all drilling operation. CRATER FORMATION When a bit tooth impacts a rock, the rock is elastically deformed until the crushing strength of the rock is exceeded, at which time a wedge of crushed rock is formed below the tooth1, 2 as shown in Fig. 1. As additional force is applied to the tooth, the crushed material is compressed and exerts high lateral forces on the solid material surrounding the crushed wedge.- en these forces become sufficiently high, fractures are initiated below the tooth and propagate to the free surface of the rock. The trajectories of these fractures intersect the principal stresses at a constant angle,'s4, as predicted by both Mohr's and Griffith's theories of failure. It has been experimentally 3,1 .6 that the volume of an impact crater, V,, varies as where Ec is the total energy imparted to the rock during the formation of the crater, and E is the threshold energy required before cratering is initiated (Fig. 2). Indexing experiments' have shown that, when there is a second free face to which the crater can fracture, a larger volume of material is removed and that above a transition zone there is a linear relationship between V, and Eo., which has a slope equal to the relationship for the single crater. The beneficial effect of indexing tends to offset the threshold energy requirement to a large extent, as shown in Fig. 2, and the relationship is closely represented by Rate-of-loading effects have been used to explain the nonproportional relationships usually obtained between drilling rate and rotary speed. The data4, in Fig. 3 show that the Ec/Vc parameter remained constant for craters produced with impact velocities ranging from 10 to 8,000 ft/sec. Since no rate-of-loading effects were detected over this wide range of loading rates, it seems improbable that there would be detectable rate-of-loading effects present in the small changes in impact velocities produced by varying the rotary speed. The writer has shown (Fig. 4) that, for craters produced in rock by impacting spheres, where X is the depth of penetration. Simon2 has shown that this relationship also holds for craters produced in rock by penetrating wedge-shaped chisels. The energy used in crater formation is

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By Tomás Vargas

The catalytic role of Thiobacillus ferrooxidans in the dissolution of chalcopyrite was studied by leaching pure massive samples of this sulfide with a pure strain of Thiobacillus ferrooxidans (ATCC 19859). Monitoring of the bacterial activity showed that an important fraction of the total bacteria generated during leaching remained attached to the chalcopyrite surface. Bacteria grown in the system, which were the offspring of bacteria adhered to chalcopyrite, was well explained as the result of the utilization of ferrous ion and sulfur as energy sources. The potential for indirect and direct action was fully utilized by the existing bacteria and the leaching process was controlled by the kinetics of chalcopyrite dissolution.

Jan 1, 1990

By William J. Stone

Large reserves of coal and uranium exist in the San Juan Basin of northwestern New Mexico. The mining and development of these resources necessarily also involves depletion of area water resources and disturbance of the hydrogeologic framework. In an effort to better define the water resources and hydrogeologic framework of this region, the New Mexico Bureau of Mines and Mineral Resources, the U. S. Geological Survey, and the State Engineer's Office are presently engaged in a cooperative study of the Hydrogeology and Ground-Water Resources of Northwestern New Mexico. The purposes of this paper are to introduce our project, review tine coal and uranium resources of the San Juan Basin, and discuss the various hydrogeologic considerations recognized in their exploitation.

Jan 1, 1976