Search Documents

By Lathrop E. Roberts

[The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of which it tends to fern a layer of highly viscous. "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and, Van Arsdale4 have shorn that the inclusion of prills of matte in the slag is also at times very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in envy laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slog as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even of only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separation ions from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and linen present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by ouch elements as vanadium and molybdenum.]

Jan 1, 1931

By STUART R. BRINKLEY, Ruth F. Brinkley

This same phonomonon of diffraction may be transposed into the X-ray domain. All that is necessary is to reduco, in the samo proportion, the wavo length of the light and the diameter of the particlo; thus, with radi- ations whose wave length is of the ordog of angstroms, the dimensions of the active particles go from 10 to 100 A that 18, the dimensions of col- loidal particlos. The evidence of this fact is shown by the following experimental schomo (fig. 1a): A narrow beam of X-rays passes through a thin layer of a modium containing micelles; the photographic film is placed a few centimeters behind the sample, and a small absorbing screen stops the direct beam in order to prevent its fogging the film. The intersect of the direct beam is surrounded by a narrow spot whose blackness decreases with the distance from the center. We will call this the spot of central diffusion (fig. 1b). The phenomenon, in spite of its relatively reat intensity, has been observed only by a few authors, who have simply given a qualitative description without attempting any quantitative de- ductions. This is due to the fact that observation of this phenonenon is not possible with the apparatus generally used to obtain X-ray diagrams, because the parasite foggings in the vicinity of the incident beam are sufficiently important to hide those produced by the sample. With the monochromator, however, used by us to obtain Debye-Sherer diagrams, this parasitic diffusion can be totally suppressed. In this way our attention was again directed to the spot of central diffraction, and we were led to make a detailed quaititative study of it.. then several papers have been published on this subject. Hosemann, using methods of calculation outlined by us, has extended them to the special case of fibrous substances, Kratky, on the other hand, starts from an entirely different theoretical point of view; ho examines the case, not of scattered particles, but of closely packed particles. 6ince We will now describe the experimental methods, summarize the calcu- lations needed in the elaboration of diagrams, and finally review the first results obtained in the vast domain of these new physical-chomical studies.

Dec 1, 1946

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Mineral Exploration Best Practice Guidelines (the Exploration Guidelines) have been prepared to assist professional geoscientists and engineers to conduct consistently high-quality work in order to maintain public confidence. The Exploration Guidelines are meant to assist professional geoscientists and exploration practitioners in planning, supervising, and executing exploration programs. In Canada, there are generally two types of public resource reporting: “Disclosure”, as defined by NI 43-101, is the reporting of technical information to the public and market participants for securities legislation purposes where a Qualified Person (QP) must be involved, and reporting of exploration information for governmental agencies to support obligations under laws including the Mining Acts of each of the Provinces and Territories. The Exploration Guidelines are also relevant where the results will not be publicly reported but are intended for internal company use. While this document is intended as guidance for work conducted or supervised by geoscientists in Canada, many of the practices described herein can be adapted to mineral exploration activities in other countries. The Exploration Guidelines are not intended to inhibit original thinking, or to prevent the application of new approaches that may develop into fundamental components of successful mineral exploration programs. Rather than provide prescriptive solutions to specific issues, they include general guidelines for current professional practice and to demonstrate and defend the merits of new methods. These guidelines do not preclude individuals and companies from developing more detailed guidelines specific to their own requirements. The initial version of the Exploration Guidelines was prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) Exploration Best Practices Committee and adopted by CIM Council on August 20, 2000. On January 9, 2018, CIM Council formed a new committee, the Mineral Resources and Reserves Committee (CIM MRMR Committee) with a mandate to, among other things, update the Exploration Best Practice Guidelines. The mandate for the committee was accepted by CIM Council on March 2, 2018. The new document was adopted by the CIM Council on November 23, 2018.

Nov 23, 2018

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By William H. Radford

Having worked some rather lorn--grade gravel during the past season at a small profit, I give the actual figures, in the hope that other mining engineers interested in this line of work may be thereby induced to do the same, in order that we may all get more data on this little-ventilated subject. The property here referred to is situated in one of the northern counties of California, where hydraulic mining is still permitted by the courts. The water-right belonging to the mine is a good one, furnishing water during about nine months, whenever there is an average rain-fall, and a fair proportion of the precipitation is in the form of snow. The ditch, about 11 miles in length, is cared for during the rainy months by two men, and during the rest of the year by one; and the water cost last season, delivered at the mine, 0.69 cent per miners' inch. The season commenced in November, 1899, and ended the last of July, 1900. During this time, 655,657 miners' inches (an inch equals 1728 cu. ft. in 24 hours) of water were used for piping, and for sweeping the bed-rock at the end of the season. From actual surveys, this amount of water washed down 1,251,399 cu. yds. of material, consisting of pay-gravel lying on the bed-rock, and varying in thickness from a few inches to 8 ft., and practically barren top-material, consisting of mountain slide, carrying considerable broken rock, clay, and soil. The banks varied in height from 50 to 130 ft., the average height being 63 ft. The grade of the sluices was 7 in. to 12 ft., the boxes being paved with block-riffles 12 in. deep. Long bed-rock cuts extended from the heads of the sluices to within a few feet of the banks, and were kept practically to grade as the work advanced. At first, electric drills were used on this work; hut as it was found that heavy blasting shattered the rock too much, and caused slips, these drills were

Jan 1, 1902

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958

By Stephen van Duin

As productivity in coal extraction demands increase in underground coal mines, the industry is faced with finding new ways to support production without jeopardising safety. In modern mines the capacity and scale of longwall coal extraction has steadily increased to a point that support processes are failing to keep pace. In particular, roadway development is continually placed on the critical path of activities which maintain mine production, so any inefficiency in this area is quickly exposed. Original equipment manufacturers are under immense pressure to modify their machines to be more interconnected with each other, with machine communication and logistical sharing of space becoming a known requirement. This paper looks at the changing trends in mining practice, analysing available technology as well as currently emerging research into hard automation and discusses the need to integrate machinery and processes in order to see increases in productivity and safety.

Aug 1, 2013

By D. Whittles, S. Kingman, K. Jackson, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

By Wallace E. Pratt

UNDER the stimulus of war psychology the American public has grown confused and jittery in its thinking on the subject of this nation&apos;s petroleum resources. This confusion arises from the failure of the average citizen, and even of many leaders in government, in our armed forces, and in the petroleum industry itself, to distinguish between our proved reserves of petroleum in the several oil-producing states and the total petroleum re- sources available to this nation. Leaders and public alike examine the accepted estimates of our proved reserves and thoughtlessly conclude that these estimates represent the total of our petroleum resources. Our fears are aggravated if we turn to the statistics on oil-finding and observe that the discovery of new reserves has waned decidedly in recent years. This confusion is dangerous because, under its influence, ill - considered policies spring up and flourish, choking out the most valuable fruits of the long experience of the American petroleum industry.

Jan 1, 1944

By Robert J. Alberts

Our shop started up in April of 1969, and during its 8th month of operation produced over 300,000 tons. Production continued to increase, and by January of 1970 tonnage rates significantly above 300,000 tons per month were being realized. Ours is a three vessel shop, producing 200 ton heats, with a normal grade breakdown indicating more than one half semi-killed carbon steel, with the balance distributed over rimmed and capped steel, alloy steel, killed carbon, and special killed drawing quality steel. The recent christening of a continuous billet caster has dictated that close to a quarter of our liquid steel be delivered to the caster.

Jan 1, 1972

By E R. Ramanaidou, M S. Piggott

Transport to and handling of iron ore at Port Hedland, Western Australia, results in the generation of airborne particulates that contribute to the atmospheric dust load, with concerns about potential local environmental impacts (eg mangrove swamps) and possible human health implications. Mineral and chemical characteristics of the Background soil samples were contaminated with particles of iron ore as martite octahedra and grains of micro-platy hematite as detected by scanning electron microscopy (SEM) in the 2.5 - 10 ¦m and 10 - 50 ¦m size fractions. Fossilized wood fragments similar to those observed in Yandicoogina fines ore were also detected in some background soil samples. With a predicted increase in demand of channel iron deposits (CID) ores and the inherently dusty Marra Mamba ores (eg West Angelas, MAC, OB29/30/35, Marandoo), in conjunction with particulate emissions from hot-briquetted iron and direct reduced iron (HBI/DRI) processing plants, there is the potential for additional sources of anthropogenic dust to contribute to background levels. Mineralogical and chemical characterisation of the entire range of particulates that could be produced is necessary for a complete understanding of their potential impact on the local environment.

Jan 1, 2002

By K-A. Adamson

If fuel cells and hydrogen are to become a mass market reality a substantial amount of further research and development needs to be undertaken. Work in hydrogen storage, production, the economics of all aspects of fuel cells and hydrogen, materials balances, and product integration are just a few of the areas that are under focus. Setting R&D targets, and providing R&D funding are therefore areas that are central to the long term development of the market, and areas in which a number of governments worldwide are highly active. Some governments, such as Japan and Korea, have set a number of very ambitious, highly focused, long term targets and are backing this up with substantial funding, others such as the EU are working on a more integrated approach, wrapping some fairly fundamental R&D into large integrated projects which run in combination with a number of other market aspects, such as public acceptance and roadmapping. The US is slightly different, in that although is has a number of long term programmes and targets, FreedomCar and SuperGen being just two, the levels of funding are set annually with the passing of each years Fiscal Budget. This paper takes three high profile regions and analyses the R&D targets and funding levels for fuel cells and hydrogen. Criteria that will be looked at include: Time frame of target(s), level of ambition, funding issues, including: Funding windows, levels available, funding barriers, overall programme goals. The added value to this paper is that it will provide a clearer picture of where each region is heading, what are its strengths and weaknesses, in terms of R&D and where there may be areas for potential international collaboration.

Jan 1, 2005

By Rajive Ganguli

A control algorithm was developed previously for loading coal trains such that each car met customer specifications (Ganguli, 2001). In developing the algorithm, the effect of the variance of coal was not investigated. This paper explores the effect of the variability of coal on the algorithm using two approaches: theoretical analysis and simulation. Both approaches demonstrate that variance is not an issue when the customer quality specification is close to the mine average quality. However, when they are far apart, the performance of the algorithm improves with variance.

Jan 1, 2002

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, located in Shanghang County, China, is a porphyry-type, low-grade ore deposit with a geological profile of upper gold and lower copper. Despite its low-grade nature, it has become one of the largest in production scale and most profitable nonferrous metal mines in China, which can be attributed to the successful application of hydrometallurgy as well as proper engineering design. A large-scale, open-air cyanide heap leach has been successfully implemented to recover gold under the humid and rainy weather conditions of southern China. Furthermore, according to the gold ore characteristics, a combination of gravity separation, carbon-in-leach and heap leaching processes was developed to improve gold recovery. In terms of copper extraction, copper ore of a grade higher than 0.25 percent is fed to the flotation plants to produce copper concentrate (gold is also enriched here), while copper ore of a grade lower than 0.25 percent undergoes heap bioleaching followed by solvent extraction and electrowinning to produce cathode copper. Additionally, a unique bioleaching system has been established at the Zijinshan Mine: low operating pH (0.8~1.0), high concentration of total soluble iron (~50 g/L), high temperatures (45~60 °C) and low activity of microorganism (~104/mL) in the pregnant leach solution (PLS). This review paper summarizes the practical experience acquired in developing the Zijinshan gold-copper mine and could be of use in other gold and/or copper plants.

By J. Astier

The idea of using only one strand for both sintering and cooling of the sinter is not new. In 1952, in the U.S.A. a sintering plant was built at Benson Mine (Star Lake, N.Y.), including : - 68 m2 or 735 sqft (8 wind boxes) for sintering, - 22 m2 or 237 sqft (3 wind boxes) for cooling. In the USSR, a large number of machines have been built allowing for cooling of the sinter on the strand, especially the 4 m (about 13 ft) machines, with : 252 m2 sintering grate area 60 m2 cooling grate area 312 m2 total grate area. However, such ventures did not prove very successful, and the IRSID embarked many years ago on a research program to discover : - what are the problems associated with cooling on a sintering strand ; - what are the possible solutions for industrial plants.

Jan 1, 1974