Search Documents

The celebrations which took place in 1986 to mark South Australia's Jubilee 150 served to focus attention on all aspects of the State's heritage. Until that time the sites and relics of South Aus- tralia's early mines had been generally neglected. Marked by the ruins of enginehouses and littered with the remains of the massive technology of the Industrial Revolution, these sites have now been recognised as containing the threads of a fascinat- ing story. In the early days of settlement the economy of the Colony was based on land and farming. Droughts caused periods of economic depression which were alleviated by chance discoveries of gold, lead, silver, and copper ore. Some of the mines which were opened on the copper deposits were the largest in the world at that time and their names well-known throughout mining circles. Working by hand with primitive equipment, the early miners excavated vast networks of shafts and stopes often extending to great depths: at Moonta- Wallaroo Mines for example workings extended to 860 m below ground. Because of the presence of underground water, mining to these depths would not have been possible without the Cornish pumping engine. Operated by steam power these massive engines and their associated equipment were transported from Cornwall by clipper and delivered to the mines by bullock cart. At this time the engines were at the peak of their devel- opment and, although expensive to import and install, they were highly reliable: the engine oper- ating Hughes pump at Moonta worked continu- ously for sixty years without a major breakdown.

Jan 1, 1987

By Clayton Vernon Deutsch, Marcel Antônio Arcari Bassani, João Felipe Coimbra Leite Costa, Vanessa Cerqueira Koppe, Pedro Henrique Alves Campos

Traditional linear approaches oversimplify the complexities of ore blending. Adopting nonlinear blending models in mining and mineral processing is critical to enhancing prediction accuracy and allowing optimization regarding nonadditive variables, such as metallurgical recovery. This study implements a simulated annealing algorithm in short-term mine planning that seeks to optimize the metal recovery by considering how to blend the ore in the mine better. Two nonlinear metallurgical recovery models are used as inputs to the algorithm to represent synergistic and antagonistic blending. The results of the case study demonstrate that the optimized schedule exhibits improvements in both blending behaviors when contrasted with conventional linear-based scheduling plans.

Jan 1, 2025

By Roe-Hoan Yoon

"Industrial flotation columns often suffer from low recoveries and high maintenance requirements because of poorly-designed air spargers. The MicrocelTM bubble generators were developed at Virginia Tech to overcome these problems. In this system, small air bubbles are generated by circulating a portion of the flotation pulp through a set of static in-line mixers. The small bubbles improve flotation kinetics and allow a higher recovery (or capacity) to be achieved. Other advantages of the system include reduced air consumption, plug-free operation and on-line maintenance. This article discusses the advantages of the MicrocelTM bubble generators and presents examples of successful in-plant demonstrations.IntroductionColumn cells are widely accepted in industry for cleaner operations because they are more selective than mechanically-agitated conventional cells. The improved selectivity can be attributed to the use of wash water which minimizes the entrainment of fine gangue particles into the froth product. Columns may also produce higher recoveries if the air sparging system is properly designed and steps are taken to minimize back-mixing. Furthermore, the quiescent conditions afforded by column cells may be beneficial for recovering coarse particles that are readily detached from bubbles under more turbulent conditions. Also, properly-designed columns offer advantages in terms of savings in floor space, reduced operating and capital costs, and simplified circuitry.It is unfortunate, however, that some of the advantages of columns are not fully realized in industrial practice. Some column circuits are unable to achieve their design capacity, while others require extensive maintenance programs. These shortcomings can usually be attributed to deficiencies associated with the design, scale-up and operation of the air-sparging system. In this article, some of the basic problems associated with commercial air sparging systems are discussed and alternatives are suggested."

Jan 1, 1994

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, ? bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of 2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By R. H. Brooks

Blasthole stoping methods were introduced at Birchtree Mine as an alternative to the original cut-and-fill and shrinkage stoping methods. The object was to take advantage of the ore structure and conditions, and achieve increased productivity. This paper outlines the design, operation and economics of three areas which utilized blasthole stoping. The 108areafrom 2300 level to 1500level was converted from cut-and-fill to sublevel blasthole stoping based on a block mining-and-filling sequence. The second area, the crown pillar of 110 mechanized cut-and-fill stope below 500 level, was recovered using horizontal rings drilled from raises within the ore zone. The third area, the 83 orebody from 1300 level to 1100 level, used the vertical crater retreat (VCR) method with large-diameter blastholes. Blasthole stoping has increased productivity and improved operating conditions.

Jan 1, 1979

By W. L. Schmidt

The effect of a water-repellent film in sandstone cores on the effective permeability-saturation relationship was investigated as part of a cooperative research program between the Bureau of Mines and the American Gas Association. The repellent film was formed by the reaction of methyltrichlorosilane3 with the connate water in the core. Other researchers have reported on the use of silicone chemicals to alter the flow characteristics of porous media (1-3, 5-7, 9, 10).4 The previous studies, however, dealt almost entirely with oil-water or oil-gas systems and not with water-gas systems. The primary purpose of this study was to determine the feasibility of using silane to retard the influx of water into natural-gas storage wells and to determine the necessary requirements for achieving this result. The success or failure of silane treatment as a remedial measure depends on its effect on gas-production rate and attendant water production.

Jan 1, 1961

By Behrouz Abedian, Livia M. Racz

"We address dynamic interactions between high-energy, reactive surfaces of polymer-matrix composites and solid surfaces. A common characteristic of these interfaces is that bonding occurs readily upon contact. In many industrial and biomedical applications, it is desirable to suppress this bonding phenomenon. This interfacial effect is discussed in light of the development of our new method of handling polymer-matrix composites in dental applications. This method involves vibration of the solid-polymer interface at different frequencies. For each material, there is a critical frequency at which the sum of the viscoelastic and inertial energies of the fluid at the surface exceeds the energy available for bonding. When the polymer is vibrated at or beyond this frequency, it does not adhere to solid surfaces. An important aspect of the developed process is that it can be used to characterize surface and interfacial properties of polymers under dynamic conditions, whereas existing techniques are restricted to the study of bulk dynamic properties.IntroductionThe purpose of this paper is to report on the development of a new method for manipulating polymer-matrix composite materials used in dental applications, and the potential of this process for use in materials characterization. The materials under discussion have polymer matrices of a combination of bisphenol A-glycidyl methacrylate (BIS-GMA) and triethylene glycol dimethacrylate (TEGDMA), and contain filler particles of silica and/or zirconia glasses. These materials are called direct aesthetic restorative materials, and are used for filling of cavities, repairing chipped teeth, and for other restorations in which appearance is of importance. They have the appearance of natural tooth material, and are therefore in great demand for use in the anterior portion of the mouth(l,2)."

Jan 1, 1998

By Z. Farhat

In spite of advances in cutting tool technology, the understanding of the basic wear behavior and failure mechanisms needs further study. Tool wear is the main factor contributing to geometrical error and thermal damage in machined components. Manifested as a reduction in tool life, it also affects the workpiece surface finish, increases cutting forces and induces residual stresses. Furthermore, the emergence of high and ultra-high speed machining processes necessitates the investigation of tool wear under these severe working conditions. Tungsten carbide-cobalt composite material has been used traditionally as wear resistant materials for many years. One main application of this material is in cutting tools. WC-Co tools consist of hard WC particles imbedded in a tough Co matrix, which functions as a binder phase. More recently, Cubic boron nitride (CBN) tool material have attracted special attention due to its high hardness and excellent wear resistance. Boron nitride in its cubic form is known to be the hardest material next only to diamond. In this paper microstructural and tribological properties of commercial grade WC-Co and CBN cutting tool materials are investigated under high speed cutting conditions. The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Four-fold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear mechanisms are proposed and are related to the observed wear characteristics in the cutting zone.

Jan 1, 2006

By Ivar Eskerud Smith, Ole Jørgen Nydal, Niranjan Reddy Challabotla, Svein Sævik

INTRODUCTION Airlift pumping, utilize compressed air that is injected at the bottom of a vertical pipe submerged in the water, reduces the mixture density inside the pipe and lifts the liquid or mixture of liquid and solids. This type of pumping technology, which is simple and without moving parts submerged in water, which provides several advantages compared to the mechanical pumping. Airlift is used in various difficult pumping applications such as transport of fluids corrosive to metals, explosives, nuclear and toxic materials in chemical industries, diamond mining and coal transport. Application of airlift to deep sea mining conditions was investigated by extensive laboratory experiments [1], theoretical analysis [2], and limited proof of concept field studies [3] starting in 1970’s with the discovery of huge amounts of manganese nodules discovered on the seabed at a depth of ranging from 4000 to 6000 m . Even after extensive investigations over the last five decades, there exists no commercial application of airlift technology for lifting of minerals. The major problems with the application airlift for deep ocean mining was (a) lack of control over the expansion of the injected gas, which increases the velocity in upper part of the riser pipe (b) lower efficiency compared to mechanical pumping [3]. Different flow regimes are encountered in airlift pumping: bubble, slug, churn and annular flow. Annular flow regime is the least efficient in lifting of particles and churn flow has better efficiency [3].

Jan 1, 2018

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By A. J. C. Paterson

High density slurry and paste tailings systems offer significant environmental benefits primarily related to reduced water consumption. However, these potential advantages need to be evaluated on a project-by-project basis. The successful design of a thickened or paste tailings system requires that the system is designed to accommodate the effect of the high density slurry on pumps, pipelines and the overall system operation. The transport system must be designed as an integrated unit and the interaction of all the components need to be considered. The transport system includes the slurry preparation plant, the pump station and the pipeline. This paper assesses the impact of increasing the slurry density in a platinum tailings system from conventional densities to thickened and paste tailings densities. As slurry density and rheology increase, there is a sharp increase in energy consumption for the additional water savings and this additional cost needs to be considered. A case study shows that there is a considerable benefit in increasing densities to the point at which tailings can be still be deposited in the standard manner. For existing systems, increasing density can result in an increased capacity at a marginal power cost, provided that the slurry is not too viscous. For a new system, a smaller pump and pipeline can result in lower capital costs and a marginally higher energy cost, if the optimum density is selected. Keywords: tailings, paste, pumping, slurry

Jan 1, 2004

By Thomas L. Wright

Exploration activities were maintained at a high level throughout 1966. Numerous significant discoveries and developments in which geologists played an important part were announced. Although the complete results of exploration activities carried out during the year by private companies have not been announced, the following are among the more important developments that have been made public knowledge. In the western states, exploration for practically all of the metals continued at a high rate. Substantially increased interest in uranium occurred this year, and it is felt by many that a real boom in the demand for uranium may come about in the near future. The reasons have been the more rapid acceptance of atomic power than had been anticipated, and that uranium producers can now sell their product to private interests and even foreign countries. A tremendous demand for uranium is anticipated by many, and this has rekindled exploration activity. On the Colorado Plateau, in Wyoming, and in the area around Grants, N. M., a number of companies have undertaken uranium exploration programs, among which are Kerr-McGee, Homestake, Anaconda and Utah Construction. A new uranium orebody in Texas was brought into production early in 1966 by Susquehanna Western.

Jan 2, 1967

This three-part report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the are handling stream. Oversize ore is causing much additional labor, creating work stoppages, and is a principal cause of accidents in metal mines. The specific objectives of the Present Systems Study were to determine and evaluate the productivity of existing ore handling systems in a representative group of underground metal mines, to relate the available historical accident record statistics of these selected mines to the specific operations in the overall ore handling operations, and to highlight the potential areas of improvement for each mine on the basis of productivity and associated hazardous index for each operation.

Jan 1, 1974

By Mario E. Rossi

Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations, to assess the uncertainty of minable reserves at the project?s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the ?correct? (or ?accurate?) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. The objective of this paper is to compare the ad-hoc ?uncertainty model? provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered and the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme. The application described in this paper is taken from a medium-sized Cu open and underground mine in northern Chile, and it demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more ?traditional? resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit.

May 1, 2001

By Rodrigo Alves Caetano

A Usiminas, maior siderúrgica latino-americana fornecedora de aços planos, tem dedicado grandes esforços para oferecer materiais mais adequados para as diferentes demandas do mercado, desenvolvendo novos tipos de aços para utilização em carrocerias veiculares. O objetivo deste estudo foi caracterizar o comportamento de dois produtos Usiminas, o aço DP780 galvanizado por imersão a quente e o aço TRIP780 eletrogalvanizado, ambos com espessura de 1,50 mm, revestimento zinco puro e camada de 50 g/m² por face, com base em análises metalográficas, ensaios de tração, ensaios de estampagem e ensaios Bake Hardening (BH) e Aging Index (AI). Os resultados destas avaliações mostraram que os aços TRIP780 e DP780 tiveram performances excelentes em todos os modos de estampagem avaliados, além de boa capacidade de endurecimento após pintura (efeito BH). Tratam-se, portanto, de boas opções para aplicação em peças da carroceria, principalmente em componentes que requeiram elevada resistência mecânica.

Aug 16, 2017

By D. M. Bondurant

AT the present time, the coal industry is greatly interested in any method or machine that will cut the cost of producing a ton of coal, while at the same time producing a product of quality and grade suitable to the customer. Comparatively new and, as yet, little known, auger mining is proving a profitable method of coal recovery. It may be used for the production of low-cost, high-quality coal with equal success from both the hard-to-mine seams, those with banded impurities and bad roof conditions, and the more easily mined seams as classified according to conventional mining methods. A number of units are now in operation and production information is available that should be of particular interest to coal operators and of general interest to anyone associated with the coal-mining industry. Auger mining refers to coal extraction with large size augers capable of drilling to great depths and having a high capacity. Consideration of the equipment and methods used in drilling an ordinary shot-hole will give a picture of auger mining on a smaller scale. At present, auger mining is used largely for recovery of coal from the highwall after strip mining becomes uneconomical because of the type and the thickness of the overburden which must be moved. Coal augers have many of the advantages of present continuous mining machines, along with many more. The four distinct operations of conventional mining-—cutting, drilling, shooting, and loading— are eliminated and replaced by the combined operation of boring and conveying of the coal. The coal recovery auger is an adaptation of the horizontal rock drill used for drilling shot-holes to shatter and loosen overburden in strip mining operations. During the war the Becker County Sand and Gravel Co. of Summersville, W. Va., experimented with drilling coal with 6 and 9-in. rock augers. The results led to the successive development of the 20, 24, 30 and the 36-in. machines, the latter having appeared in the coal fields within the past six months. Because of the great success of the smaller size

Jan 1, 1952

By N. Fardin, O. Stephansson, L. Jing

A pair of silicon rubber replicas of size 250 mm by 250 mm, from a natural rock joint, was used to produce several high strength concrete fracture replicas of different sizes, from 50 mm by 50 mm to 200 mm by 200 mm. The morphology of the concrete fracture replicas were digitized at the laboratory using a 3D-laser-scanning machine with high accuracy and resolution. The scale dependency of the geometrical properties, including surface roughness and aperture, of the samples were investigated using fractal method. The investigation was extended to study the scale effect on the mechanical properties of the concrete fracture replicas. Four concrete replicas having same geometry from each sampling size were sheared under four different normal loads. The results show that normal and shear stiffness and peak shear strength decrease with increasing sample size and decreasing normal stress. It is concluded that for accurate determination of geometrical and mechanical properties of rock joints in the laboratory and field scales, samples with size equal to or larger than stationarity limit are required. Silikongummiabdrücke der Größe 250 mm x 250 mm einer natürlichen Kluft dienten als Vorlage für mehrere Hochfestbeton Rissreplikas verschiedener Größe. Die Morphologie der Beton Rissreplikas wurde mittels eines 3D-Laserscanners hoher Genauigkeit und Auflösung im Labor digitalisiert. Die Skalenabhängigkeit der geometrischen Eigenschaften, dies inklusive Oberflächenrauhigkeit und Öffnungsweite, wurden mittels Fraktalen bestimmt. Die Studie wurde durch die Untersuchung der mechanischen Eigenschaften der Betonrepliken erweitert. Hierbei wurden vier Betonrepliken der selben Geometrie jeder Probengrösse unter vier verschiedenen normalen Belastungen abgeschert. Die Ergebnisse zeigen das sowohl Normal- und Schersteifigkeit als auch die Spitzenscherfestigkeit mit zunehmender Probengrösse und abnehmender Normalspannung abnehmen. Es hat sich gezeigt, daß für eine genaue Bestimmung der geometrischen und mechanischen Eigenschaften von Felsklüften im Labor und im Feld Proben einer Größe gleich oder größer des stationären Limits verlangt werden. Deux répliques en gomme de silicone d’une fracture naturelle, de dimension 250 mm par 250 mm, ont été utilisées pour produire des répliques en béton de haute résistance de dimensions allant de 50 mm par 50 mm à 200 mm par 200 mm. La morphologie de ces répliques a été digitalisée au laboratoire à l’aide d’un laser-scanner 3D haute résolution et haute précision. L’influence de l’échelle des propriétés géométriques, incluant rugosité et ouverture, a été étudiée en utilisant la méthode des fractales. Des essais complémentaires ont été réalisés afin d’étudier l’effet d’échelle sur les propriétés mécaniques des répliques de fracture en béton. Quatre répliques béton de même géométrie pour les différentes tailles d’échantillons ont été cisaillées sous quatre valeurs de contrainte normale. Les résultats montrent que la rigidité normale et tangentielle ainsi que la résistance de pic diminuent en proportion de l’augmentation de la taille de l’échantillon et de la diminution des contraintes normales. On peut en conclure que, pour une détermination précise des propriétés géométriques et mécaniques des fractures au laboratoire et sur le terrain, des échantillons de taille égale ou supérieure à la limite stationnaire sont nécessaires.

Jan 1, 2003