Search Documents

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By AIME AIME

THE stage is set for the 1930 Annual Meeting. It will take place in the Engineering Societies Building. Feb. 17, 18, 19 and 20, and an unusual pro- gram of technical papers, symposia, lectures and addresses, interspersed with luncheons, dinners, excursions and worthwhile entertainment for the four days has been arranged. The curtain rises on Monday morning and the first act is by the entire company-registration. Then the meeting hits its stride, for there are ten technical sessions on Monday, and the range of subjects includes most of the Institute membership. The Committee on Coal and Coal Products, which is about to become the Coal Division, presents a symposium of a dozen or more papers on Coal Classification, concluding its afternoon session with several papers on general subjects. At its luncheon between sessions, C. E. Bockus, president of the National Coal Association, will be the honored guest. Papers of theoretical character will be discussed at the morning session of the Committee on Geophysical Prospecting; at its afternoon session there will be presented summaries of results obtained at various properties by methods described at previous meetings of this group and permanently recorded in "Geophysical Prospecting," published by the Institute early in 1929. Members of the Petroleum Division should not overlook the paper by Theodor Zuschlag, on this Committee's program. It is entitled, "Oil Structure Mapping by the Sundberg Method." Members of the Iron and Steel and Institute of Metals divisions will find it profitable to attend the session on Engineering Education on Monday afternoon. E. A. Holbrook has arranged a program of ten-minute talks on Metallurgical Education which are designed to get down to "brass tacks." and the practical man may, in discussion, contribute as well as learn. At 5 p. m. Thomas T. Read will lecture+ at Columbia University, on "Recent Progress in Economics of the Mineral Industries."

Jan 1, 1930

By R. R. Sayers

"According to the dictionary,3 an accident is an event that takes place without one's foresight or expectation, often an undesigned, sudden, and unforeseen occurrence of an afflictive or unfortunate character. However, actual experience with accidents, the second most important cause of death in the United States,4 and a more extensive and scientific inventigation of their causes indicate that from 75 to 90 per cent of accidents are avoidable.5 This is borne out by the results of a three-year study of the accident records of 64,000 motor vehicle operators in New York6 which show that certain drivers are prone to accidents, that accident experience is traceable to certain causes, and that accidents don't just ""happen,"" It is estimated that 97,000 persons were killed by accidents in the United States in 1929 and 15,000,000 were injured. Of these about 23,000 deaths were due to so-called industrial accidents. In a list of accident rates by industries, compiled by the National Safety Council7 from reports of member establishments, mining heads the list, in both frequency (74.43 per 1,000,000 man-hours worked) and severity (9.9 days lost per 1,000 man-hours worked). These figures are very much higher than for any other industry; theindustries showing figures most comparable to mining are meat packing with a frequency rate of 55.94 and a severity rate of 1.47, construction with a frequency rate of 50.41 and a severity rate of 4.62, and refrigeration with a frequency rate of 43.35 and a severity rate of 3.04.While there is no way to determine the actual cost of all accidents from a monetary standpoint, estimates indicate that the cost will run into hundreds of millions of dollars annually.Cost of accidents in metal mines.- The United States Bureau of Mines obtains accurate figures on the number of lost-time nonfatal accidents as well as fatal accidents in the metal-mining industry.8 In 1926 the metal mines employed 127,823 men; 430 men were killed and 30,350 men received lost-time but nonfatal injuries as a result of accidents. Each of these fatal and nonfatal injuries averaged 114 days lost time, computing a fatality as 6,000 days lost time. This is equivalent to 3,523,944 days time lost due to accident, or at $5 per day per man, to a wage loss of $17,619,720. Deducting one-ninth of this figure for compensation paid, the metal miner loses in wage annually about $15,700,000, or about $122 per individual. This average loss per individual includes the cost of fatal accidents reckoned at 6,000 days or $30,000, but even if the loss in time due to fatal accidents be deducted, the average cost to each individual metal miner each year for nonfatal accidents is about $32. Estimating the loss to the metal-mine employer as about the same as that to the employee, the annual cost of metal-mine accidents to the employer is about $15,700,000 and to the employer and miner is $31,400,000."

Oct 1, 1930

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By AIME AIME

BUSINESS forecasting may be an inexact science, if it is a science at all, but in the opinion of the statisticians of the American Telephone & Telegraph Co. it is a valuable aid to the making of future business plans, whether it be used by a telephone system, a manufacturer whose distribution is country-wide or, one whose trade is confined to certain sections. Whatever the defects of business forecasting may be; the American Telephone & Telegraph Co: has employed it since 1921, not only for charting the probable; course of telephone traffic over long-distance lines, but' to determine the needs for new plant and equipment: caused by shifting tides in business or increases in population or general industrial expansion.

Jan 1, 1929

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By Spencer P. Howell

One of the important problems in metal mining , tunneling or quarrying is the most economical method of bringing down the ore or rock . The two factors having great influence in determining this are arilling and blasting costs . In considering the efficiency of the explosive used , the diameter of cartridge has always been supposed to play an important part . However , the Bureau's attention has been called to the lack of definite data on the effect of cartridge diameter on the strength and sensitiveness of high explosives . This information is especially valuable to the user of explosives as it assists him to determine what diameter of borehole is most economical . A paper* on "The effect of cartridge diameter on the strength and quickness of high explosives " was submitted to the sub- committee on Drills and Drill Steel of the 24th Annual Convention of the American Mining Congress by Charles S. Hurter , Technical Representative of the E. I. duPont deNemours and Co. In this paper Mr. Hurter points out that the physical characteristics of an explosive most affected by the diameter of cartridge are rate of detonation and sensitiveness to explosion by influence , and that both increase with increase in diameter . As there is a continuing tendency to the use of smaller diameter drill holes in order to lower drilling costs , and as the smaller drill hole requires a smaller diameter of explosive cartridge than larger drill holes do , this paper has been prepared to show the effect the diameter of cartridge will have on the strength and sensitiveness of the high explosives which may be used . Accordingly , the Bureau of Mines , in cooperation with the Institute of Makers of Explosives , has carried out a series of tests to show the effect of cartridge diameter on the strength and sensitiveness of certain high explosives .

Jan 1, 1923

By Jack R. Woodyard

Bonding angles, promotion energies, and relative atomic sizes can be estimated through the solution of a set of algebraic equations generated from simple atomic models, and quantum mechanical parameters such as bond strength can be estimated from simple, hydrogenic form-wave functions. The precepts of The Engel-Brewer Theory are melded with the "Crystal Approximation Model" to produce atomic-structure models making these predictions, The two-valence-electron case is presented in this report. For the candidate atoms Be, Mg, Ca, Sr, and Ba the calculated promotion energies agreed within a few percent of their experimental values. These atomic parameters determine the possible crystal structure of the candidate atoms when alloyed. This is part of the effort at the U.S. Bureau of Mines to develop methods for alloy design in response to requirements for new high-performance alloys that conserve critical or rare materials.

Jan 1, 2010

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining, estimating post blasting displacement and spillage accurately is essential to guarantee operational efficiency, ensure alignment with production plans and their associated key performance indicators. The absence of predictive modeling tools on blasting operations results in several critical challenges, including operational reworks due to deviations in material displacement, significant discrepancies between mine and plant (ore grade dilution included), misalignment with the reported production plan, and increased operational costs due to inefficient use of resources. This study, conducted at Los Bronces Mine operated by Angloamerican, Chile, addresses the application of a three-dimensional simulation tool that, through numerical modeling, is capable of predicting post blast rock displacement. The implementation was carried out in a pit phase characterized by blasts near the pit boundaries, with a high risk of material spillage and potential blockage of the only access ramp to the extraction levels. By the integration of key design parameters, such as blast pattern geometry, detonating time, explosive charge distribution and pre and post blast survey, an optimal calibration was achieved and validated in seven blasting events to date, reaching an accuracy greater than 80% in estimating post-blast rock displacement and spillage volumes. Furthermore, this study allowed the evaluation of different pattern alternatives with and without spillage mitigation measures (use of air decks near the free face), obtaining a high correlation and accuracy exceeding 95% in predicting the selected design outcome, supporting optimal design selections. The result highlights the usefulness of the model as a decision-support tool for blasting engineers and short-term planning, by reducing the need for unnecessary operational reworks, improving geological and operational reconciliation, and ensuring the alignment of the extracting plan with production targets. The current average deviation is 15%, with higher deviations observed in blasts with smaller volumes of spill or where the simulated sequence was changed before blasting. The use of this type of three-dimensional numerical modeling represents a significant advancement for blast engineering and the optimization of key performance indicators in open-pit mining operations.

Jan 26, 2026

By J. C. Barry, J. H. van Laar, P. L. Crouse, H. Bissett, I. J. van der Walt

"Plasma-assisted spheroidisation of metal powders offers several technical advantages with respect to both the ease of materials handling and powder-metallurgical item manufacturing. Advantages include improved flowability, increased powder packing density, elimination of internal component cavities and fractures, changes in morphology resulting in decreased friction between particles and contamination during pneumatic transport and enhanced particle purity. In this empirical study, spherical iron particles were produced using a microwave plasma operating at atmospheric pressure and characterized using optical microscopy and SEM techniques. Iron powders were fed into the system at fixed operating conditions, resulting in particles with spherical structures. The theoretical estimate of the time required for melting to occur is 1.6 ms, an order of magnitude smaller than the actual residence time. IntroductionParticle design and functionalization has become an increasingly popular aspect of materials synthesis and powder-metallurgical item manufacturing. One such technique involves the spheroidisation and densification of feed materials, typically in the form of chemical powders with wide particle size distributions. The major benefits of powder spheroidisation include improved powder flowability, increased powder packing density and powder purity, reductions in internal voids and defects, as well as the ability to manipulate the particles surface morphologies (Boulos, 2004). Thermal plasma processing has the potential for scale-up and for producing industrial quantities of spheroidised powder.Thermal plasma technologies offer a wide spectrum of material synthesis and treatment options, amongst others the synthesis and spheroidisation of nano-sized ceramic and metal particles (Kumar and Selvarajan, 2006). The spheroidisation process occurs within the plasma discharge via in-flight heating and melting of the powder feed material, given high enough plasma temperatures (Fridman, 2008, p. 495). Surface tension in the molten droplets results in spherical, or nearly, spherical, powder particles being formed upon exiting the plasma discharge where the droplet undergoes rapid cooling and freezes. Quite often, the bulk density of these spherical particles is higher than that of the starting material (Boulos, Fauchais and Pfender, 2013, p. 42). The different plasma spheroidisation techniques reported include radio frequency (RF) induction thermal plasmas (Jiang and Boulos, 2006; Karoly and Szepvolgyi, 2005; Yuming, Junjie and Yanwei, 2013), nontransferred direct current (DC) thermal plasmas (Chaturvedi et al., 2014; Kumar and Selvarajan, 2008; Suresh, Selvarajan and Vijay., 2008) and microwave-assisted plasma processing methods (Chen, Gleiman and Phillips, 2001; Vanamu et al., 2004; Weigle et al., 2004)"

Jan 1, 2016

By R. J. Teitel

The Pb-U system has been investigated by X-ray, thermal, and microscopic analyses. Two pyrophoric intermetallic compounds were found; UPb3 and UPb. The crystallographic structure of UPb3 is reported. A phase diagram was drawn for the system showing three eutectic and one syntectic reaction. AS a result of the interest in uranium metallurgy, the Pb-U system has been investigated. Practically no quantitative data appears in the literature concerning this system. Chips were machined from bars of high-purity uranium obtained from Ames Laboratory and the lead was 99.9 pct high-purity grade from Bel-mont Smelting & Refining Co. The chips were pickled in a dilute solution of nitric acid, washed in water and then alcohol, and dried prior to use for alloy preparation. The lead was simply sheared from the pig with no chemical treatment. Lead and uranium were placed in graphite crucibles and loaded into an induction furnace. In order to insure good alloy formation, the lead was loaded above the uranium to wash the uranium chips into the melt. After the charge was held at the desired preparation temperature for 15 to 30 min, it was allowed to cool in the crucible. The entire melting operation was accomplished in an atmosphere of helium (double charcoal refined grade with no further treatment). The procedure was to outgas the furnace by first evacuating it to 10-% m Hg, admitting helium to 8 psi gage and sealing the furnace off. An optical pyrometer focused on the charge through a hole in the crucible cover was employed for thermal measurements. Usually a 50° to 70°C correction had to be added to the instrument value. The most suitable alloy preparation temperature range was found between 1220° and 1280°C. The reason for this is explained by the phase diagram, Fig. 7. Above this temperature range two liquids separate preventing alloy formation upon cooling at a reasonable rate. On the other hand, below this range the uranium was coated with a layer of both compounds and the rate of reaction was diminished by diffusion processes. The fastest reaction rate occurred in this narrow range of temperature because only UPb coats the uranium and it evidently does not protect the uranium as well as UPb,. Apparatus and Procedures The development of apparatus and techniques was determined by the peculiar properties of the alloys. All the alloys were pyrophoric, and, consequently, the alloys had to be protected from oxidation by handling them in a dry box or inert atmosphere furnaces. Other operations performed outside of this equipment had to be done as quickly as possible. Thermal analyses were conducted in a furnace and arrangement similar to that described by the author.' Graphite crucibles having a thermocouple well in the bottom were used to contain the prepared alloy, while a helium atmosphere protected the melt from oxidation. The furnace was outgassed by pumping a 10-3 mm Hg vacuum until the furnace had been heated to 400°C. Then helium was admitted and the furnace sealed under 8 psi gage pressure. Chromel-alumel thermocouples were used for thermal analysis and the accuracy of thermal measurements was judged to be k 5°C. At first, an attempt was made to use platinum-platinum-rhodium thermocouples, but evidently lead vapors attack it at high temperatures forming low melting alloys. These lead vapors had direct access to the thermocouple because the graphite crucible was porous. A differential temperature control was used to regulate thermal analyses. The thermal gradient across an alundum tube placed between the windings and the crucible was maintained constant by a controller.

Jan 1, 1953

By John Wellington Finch

THE- impression which the public has of northern Canada is that it is a' vast wilderness of forests; river's, and. lakes, sparsely inhabited by. a few Indians and `containing a few, scattered trading posts of the Hudson Bay Co. This is far from the facts. The building of the Canadian Pacific Railway led to the discovery, in 1883, of the nickel deposits of Sudbury, Ont.; these are the largest known nickel deposits in the world and produce about 90 per cent. of the world's output of nickel. The building of the Temiskaming and Northern Ontario Railway north, from North Bay, to open up farming lands along Lake. Temiskaming, resulted in the discovery and development of the great silver deposits of the Cobalt area, Ontario. Since the discovery of these deposits in 1903 to Dec. 31, .1923, Cobalt has produced a total of ' 327,301,897 oz. of silver, valued at $212,668,434, and paid in. dividends $88,338,185. In 1923 the production of Cobalt amounted to 10,285,247 oz. of silver. Just south of Cobalt, in South Lorrain,. a. new silver district has recently been developed and mills have started production. These deposits are of such extent that 'a branch railroad is under construction from Cobalt to that area. Northwest of Cobalt is the Gowganda silver area which is also a producer of silver ore and is now attracting outside attention. This area is not connected by railroad.

Jan 1, 1924

By G. K. Quainoo

Investigation by researchers on the application of various thermo-mechanical process histories on 6000 series aluminum alloys have found improvements in mechanical properties of these alloys. However, natural aging, which is unavoidable in the automotive processing line, has been found to have deleterious effect on subsequent artificial aging properties in these alloys. In this study, the evolution of yield strength during natural aging modeled by Lloyd and Gupta has been adapted to investigate the effect of cold deformation on the natural aging kinetics in AA61 11 by means of tensile testing, differential scanning calorimeter (DSC) and scanning electron microscopy (SEM). Also, intermetallic particles in the alloy were extracted from the matrix and XRD performed on them to ascertain their composition and their role on the kinetics in the alloy. The results show that cold work effect on the natural aging kinetics of AA6111 is in very good agreement with the model proposed by Lloyd and Gupta. The kinetics of natural aging in AA6111 aluminum also decreases with increasing level of cold work. This is attributed to dislocations serving as sinks which consume quenched-in vacancies formed during the early stages of clustering. The phases of the intermetallic particles identified in AA6111 are those of a-A15Mn12Si7 and a-A15MnSi.

Jan 1, 2007

The Council of the Institution of Mining and Metallurgy submitted the report of the affairs of the Institution for the session 1970-71, and the Statement of Accounts for the year ended 31 December, 1970. The statistics given in the report refer to the calendar year 1970. Details are included of membership, officers, representation on other bodies, honours and distinctions, awards, meetings, publications, library, overseas activities, fellowships and grants, the revenue and expenditure account, the balance sheet, trust fund balances, contributing companies, and schedule of investments

Dec 1, 1971

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador is a surface deposit enriched in the highly sought after heavy rare earth elements. Early metallurgical work investigated beneficiation of the rare earth content of the Foxtrot resource using flotation, gravity separation and magnetic separation. The concentrate was then processed by acid baking and water leaching to produce a REE leachate for purification and recovery. The Search Minerals Direct Extraction Process was developed through bypassing the beneficiation process and directly acid treating a coarse crushed ore material prior to water leaching. The result is a simple, low risk technical process for direct recovery. Concurrently, the treatment of the water leach solution was modified to produce a high grade (98.9% total rare earth oxide) product for refining.

Jan 1, 2016

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009