Search Documents

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By Rudolf Keller

In the electrolysis of neodymium oxide from a molten fluoride electrolyte, anode effects may occur at the carbon anodes, interfering with smooth cell operation. In laboratory experiments, we attempted to circumvent this problem by selecting electrolytes with a high oxide concentration, possibly at relatively low rare earth content, but cathodic deposition was not satisfactory. A regime at higher cell voltage was discovered to yield good cell performance, but evolution of considerable amounts of fluorocarbon compounds suggested that a reactive treatment of the off-gases would be necessary for environmental acceptability. Subsequent experimentation at low cell voltage revealed conditions for satisfactory operation without occurrence of anode effects and without formation of any CF4 or C2F8.

Jan 1, 1997

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method's capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

By D. Kruse

Top-down constructed large-diameter (up to 90 m or 300 ft) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to analyze various failure modes, evaluate the shaft liner and internal structures' response to seismic loading, assist in segment design and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored. Mining Engineering, 2011, Vol. 63, No. 9, pp. 81-88. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By John Griffen

DURING the past year, purchases of coal-preparation equipment and the discussions and plant-scale tests conducted indicate that much attention is being given to better recoveries of coal by preparation plants and improved quality of the finer sizes to widen their market. In the anthracite regions the new equipment was predominantly for the cleaning of the steam sizes, much of it for treating No. 4 and No. 5 buckwheat. The units installed were largely coal-washing tables, Hydrotators, and Menzies cone separators.

Jan 1, 1944

By H. M. Gao

According to the difficulty of dolomite removal from collophanite,normal-reverse floatation process has been adopted in floatation with the use of highly selective collector G-4 and depressant S721. Good indexes of flotation have been obtained with the run-of-mine ore containing 17.96 % P2O5 and 2.31 % MgO being upgraded to a concentrate containing more than 30% P2O5 and less than 1% MgO. The reagent interaction mechanism in low grade collophanite flotation has been stu-died by FTIR analysis and theoretical calculation. The results indicate that the interaction between collector G-4 and collophanite is the result of chemical adsorption in combination with physical ad-sorption with chemical adsorption playing the major role. Depressant S721 adsorbs on dolomite surface to form a water film and effectively depresses the flotation of dolomite and reduces the MgO content in the concentrate.

Jan 1, 2014

By Nord L. Gale

The discovery of important new ore deposits of lead, zinc, copper and silver in 1955 in Southeastern Missouri has resulted in the development of a thriving mineral industry known as the "New Lead Belt" or "Viburnum Trend", to distinguish it from the older lead producing areas to the East. This region has recently become the world's largest lead producing district with production in 1970 reaching 432,576 tons or 74.4% of the entire United States lead mine production. The area is heavily forested with rolling hills dotted with numerous clear running streams in the Clark National Forest of the Missouri Ozarks. The location is within 70 miles of St. Louis, Missouri and has a natural abundance of water resources which provide an important recreational area for fishing, hunting, camping and other outdoor activities. Until this recent development, the area was sparsely populated and industrialization was almost unknown. The infusion of $150 million in mining capital has brought about a dramatic change in the economic structure of the area and will almost surely be accompanied by changes in its environmental picture. In an effort to maintain this bountiful national resource and to evaluate the changes occurring in surface water quality and aquatic life forms present, an inter- disciplinary research program at the University of Missouri has been undertaken with the support of the National Science Foundation. Research has been carried out to determine background values, establish natural baselines, and to evaluate the extent and causes of changes in streams effected by mine water discharges and wastewater from ore milling operations. The unique topography of the "New Lead Belt" area allows the channelization of milling and smelter wastes to separate stream systems (Figure No. 1) thus allowing measurements of the pollutional effects on an individual basis.

Jan 1, 1973

By S. Budirsky

J.B. Gwiazda's article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point O travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex '85, Katowice, Poland, pp. 73 -83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4600 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (la in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the afore- mentioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda's opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf -Forschungshefle, 1984, NO. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1988

As longwall shields are lowered in preparation for advance, dust from the canopy falls directly into the air stream with the potential of becoming entrained. Historical dust sampling data from the early 1980s shows that shield advance contributed an average of 12 percent to the airborne respirable dust levels found on longwalls in the United States. Data from the 1990s indicates that shield dust liberation had increased to an average of 23 percent. Increased longwall production levels over this time resulted in the need to move a larger number of shields during each shift, while an increase in air velocities on the face was also occurring. These factors combine to suggest that greater quantities of shield dust are being entrained into the face air. A series of controlled laboratory tests were conducted in a test stand simulating shield dust entrainment to evaluate changes in airborne respirable dust levels at different air velocities. Significant differences in respirable dust entrainment were observed. The test facility, test methodology, and dust sampling results will be reviewed and discussed

By A Pettersson

LKAB owns and operates two of the largest underground mines in the world in Northern Sweden. In Malmberget, with a production capacity of about 30,000 t/day of iron ore, the current main 815 m haulage level is rapidly approaching the end of Its life and plans are being made for its replacement on the 1000 m level. Due to the separation of the orebodies, trucks have been chosen for transporting the ore from the orepasses to the crushers. The trucks currently in use have a capacity of 120 tons. To increase the efficiency of the loaded haul, the new main level will have a favorable slope from the drawpoint locations to the crushers. From the new level the crushed ore will be transported by conveyor to the 815 m level for hoisting to the surface. The paper discusses the planned mining and transportation system.

Jan 1, 1998

By C. Groccia

As the search for new ore bodies drives mines to be developed at greater depths, the associated high stress environments present challenges for rock support design. Excavations in highly stressed brittle rock are often subject to large volume increases due to rock failure, a phenomenon known as rock mass bulking, which can result in significant wall convergence. Support systems need to be designed to minimize the amount of bulking and to accommodate large wall convergences. In order to design such a support system, empirical guidelines are often used to predict the amount of bulking. However, the empirical guidelines that are currently available are based on a limited number of case studies and consider few input parameters, which may result in an inaccurate bulking assessment. This paper describes methods of collecting quantitative field data at Creighton mine in Canada to better understand rock mass bulking and to further develop the empirical guidelines for bulking assessment for tunnels in highly stressed grounds. Measuring

Aug 1, 2013

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By Herman D. Mendoza

A rapid recovery/recycling process was introduced utilizing the surface-chemical properties of finely dispersed mercury and alumina (Al2O3) fibers in aqueous environment. The conventional method of amalgamation or .ball milling. involves the mixing of a substantial amount of mercury to collect free gold during the grinding stage. In effect, a portion of the mercury is transformed into minute droplets that readily float and disperse in the amalgamation effluent. The fine droplets of mercury in the dispersion readily attached onto the positively charged macroscopic alumina fibers (i.e. = pH 9.8) at conditions pH 3 to 10. When an effluent from settling procedure after an amalgamation-grinding stage is passed through a column-bed packed with alumina fibers, maximum collection of negatively charged finely dispersed mercury occurred at pH 3 to 6. The collection/attachment efficiency was 99.5%. The collected droplets of mercury, which are left in the column-bed of alumina fibers, were subsequently rinsed with alkaline solution at pH 10 to 11.5. At these conditions, both mercury and alumina fibers carry negative surface potentials and resulted in the partial detachment of mercury from the alumina fibers. The detachment efficiency was only 30-35%. The attachment/detachment mechanisms in this study were analyzed using the DLVO theory.

Jan 1, 2003

By James C. Hower, B. K. Parekh

Introduction The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; and (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Although boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist; density differences; the relative friability of the coal and its associated impurities; hardness; and strength. Some of the other factors related to preparation are petrographic composition and rank. RANK CLASSIFICATION Coal is a general designation for a great number of solid organic minerals with different compositions and properties; all are rather rich in carbon and have a dark color, generally black. Next to mineral oil and kerogen, coal is the most important reservoir of carbon in the world. Carbon is an indispensable necessity of life as well as the main source of energy. Coals are found in stratified deposits, sometimes at great depths. All coals owe their origins to slow decomposition and chemical conversion of immense masses of organic material. As found in seams, coal is a heterogeneous mixture of organic and inorganic materials. Not only are there large differences in the properties of coal originating from different seams, but also in coal removed from different locations in a single seam. A genetic relationship exists between peats, brown coals, lignites, biturninous coals, and anthracites. As a whole, the process of coal formation, or coalification, proceeds as a continuous transformation of plant material, each phase characterized by a degree of coalification, or rank. As a measure of this rank, the carbon content or some related parameter can be used.

Jan 1, 1991

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

By J. J. Scott

Friction Rock Stabilizers, trade name Split Set*, is a new support system invented by the author and under development by Ingersoll-Rand and Lee-Norse Company. Split Sets are a substitute for standard bolts or fully grouted resin bolts and have certain advantages which are: 1. Improved safety for the miner 2. A rational design is possible based on rock mechanics principles 3. Supports can be made either to be yieldable or rigid 4. Supports can be used to build a roof beam or to suspend roof material 5. It is cheaper than the resin system and costs about the same as standard bolts.

Jan 1, 1974

By W. L. Staker

The Bureau of Mines investigated the use of shredded automobile scrap for copper cementation. Air agitation was used to improve the cementation rate and prevent excessive buildup of copper on the iron. The pieces of scrap were too large to be properly evaluated in the laboratory; therefore, a pilot scale test unit was constructed and the process tested at field locations. Pregnant solution was obtained from industrial leaching operations, processed in the test unit and the barren solution and cement copper were returned to the plant process stream. The test results showed that the air-agitated launder containing auto-mobile scrap was an effective means for recovering copper from leach solutions. A continuous l4-day test run was made without a noticeable decrease in cementation efficiency. The most suitable scrap product was obtained from incinerated automobile hulks shredded in a hammer type of shredder. However, it was necessary to remove small pieces such as nuts and bolts because they interfered with the discharge of the copper product.

Jan 1, 1976

By Matveyeva Tamara

The main deposits of gold-sulfide ores of Russia are characterized as refractory raw material with the non-uniform finely-interspersed sulfide mineralization, submicron gold, the low gold content (3-5 ppm) and non-uniform distribution of the gold associated with pyrite and arsenopyrite. These ores show low indicators of extraction of gold and silver at cyanidation. Flotation is one of the basic technological procedures of processing of gold sulfide ores however simultaneous presence of pyrite and arsenopyrite and lack of effective methods of their selection constrains application possibility of flotation schemes because of rigid requirements to flotation concentrates under the arsenic content and practically excludes smelting of pyrite concentrate. The main losses of precious metals at flotation technologically are concentrated in thin classes (up to 15 %) demonstrating an inefficiency of standard reagent modes. For an estimation of expediency and possibility of application of selective flotation of pyrite and arsenopyrite a scientific substantiation of the mechanism and criteria of selection of gold-bearing ferrous sulfides of various material structure is developed and for difficultly divided pairs of sulfides with close technological properties the new selective reagents providing effective extraction of gold from hard-to-beneficiate ores are designed. The original technique for modifying surface composition of natural sulfides by nano-sized Au is worked out and the mechanism of selective adsorption of new reagents ? oxypropyl ester of diethyl-dithiocarbamatic acid (OPDTC) and oak bark extract (OBE) on Au-bearing sulfide minerals is revealed. Formation of almost insoluble OPDTC-Au compounds is defined by methods of scanning electronic microscopy (SEM) and UV-spectroscopy. Application of developed reagent modes using new reagents have been tested in laboratory conditions at flotation gold-sulfide ores samples and collective concentrate probes providing high extraction of gold and improved quality of the concentrate (less than 2 % As). Keywords: pyrite, arsenopyrite, selective flotation, flotation reagents adsorption, complex-forming, gold recovery.

Sep 1, 2012