Search Documents

By J. M. Camp

In conforniity with the design of the oficials of the United States Steel Corporation for the standardization of the methods employed in the sampling and analysis of all materials encountered in their various lines of manufacture, the Chemists' Committee presents this compilatioti of standard methods for the sampling and subsequent analysis of molten pig-iron. In selecting the methods, the Committee employed the same line of procedure as in former cases, viz., the careful consideration of all the methods employed in each laboratory of the Corporation, evolving therefrom the several methods herein described, the immediate adoption of which is desired. The services of Messrs. W. B. N. Hawk, William Brady, and C. H. Rich, a sub-committee appointed for the preparation of the present paper, are gratefully acknowledged. II. Introduction. A quite obvious cause of nonconformity of results of comparative analyses in the various laboratories of the Corporation has been an apparent lack of uniformity of method in the sampling and analysis of molten iron. This condition is particularly apparent with regard to the determination of the sulphur, numerous discrepancies in which would appear t.o indicate the absence of, and the necessity for, some uniform method of procedure. The estimation of the

Jan 1, 1913

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By T. F. Tomb

Past experience has shown that the penetration characteristics of the 10-mm nylon cyclone used on approved personal sampling equipment are significantly different from those determined in the laboratory using a nonpulsating flow source. The Bureau of Mines has developed and recommended a modification to presently approved equipment that will alleviate this difference. However, as a result of this modification, a new relationship for converting respirable dust concentrations measured with approved personal sampling equipment to equivalent concentrations as measured with an MRE instrument will have to be established. This Bureau of Mines report describes the underground sampling program conducted to establish a new factor for converting respirable dust concentrations measured with personal sampling equipment, modified with a recommended pulsation damping device, to an equivalent concentration as measured with an MRE gravimetric dust sampler.

Jan 1, 1973

By J. M. Karpinski, F. P. White, R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball, the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corp.'s Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about 50% without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1972

By Alvaro Veizaga, Samuel Cuellar

In recent years, Industry 4.0 has generated a change in the way companies in various industrial sectors design, produce and deliver products and services, and is focused on the interconnection of systems, the advanced access and management of large amounts of data in real time, and the implementation of emerging technologies such as the Internet of Things (IoT). Artificial intelligence (AI), machine learning (ML), digital twins (DT), robotics, virtual and augmented reality (VR/AR), among others [1]. DTs are accurate and dynamic virtual models that replicate physical systems, where it is possible to simulate and optimize operations before implementing real-world changes [3]. These features make it possible to reduce investment costs, minimize risks and improve strategic decision-making. These benefits are of utmost importance for tailings storage facilities (TSF), since they are facilities aimed at the safe storage of tailings and with the constant need for growth [4]. This paper evaluates the applicability of a DT in a TSF from a conceptual perspective, providing the advantages of its implementation, but also the barriers identified in the industry based on the authors’ experience.

Feb 1, 2025

By Robert A. Rapp

The standard molar free energy of formation of MOO,was determined between 750o to 1050o C in galvanic cell measurements involving the solid electrolyte Zr0.85 Ca0.15 O1.85. Use of the reference electrodes Fe + FexO and Ni + NiO Provided two independent determinations of FoMoo2. The data may be represented by the equation FMoO2 = -137,500 +40.0T(°K) which is in good agreement with previous CO/CO, gas equilibrium measurements of Gleiser and Chipman. The standard molar free energy of formation of molybdenum dioxide has recently been reported over a large range of high temperatures from the calorimetric experiments of King, Weller, and christensen.' Gleiser and chipman2 have also recently determined ?FmoO2 from 926o to 1068oC in CO/CO2 gas equilibrium measurements. Earlier gas equilibrium studies have been made and reviewed by Gokcen.' Over the temperature range studied by Gleiser and Chipman their values for ?FoMoO2 differed from the calorimetric data by about 700 cal. This investigation was undertaken to resolve this difference and thereby establish the two phase mixture of Mo + MOO, as an electrode of well-known oxygen potential for galvanic cell applications at very high temperatures. The galvanic cell technique involving the Zr,.,, Ca,0.15 01.85 solid electrolyte was introduced for the

Jan 1, 1963

By M. A. Creaney

"The Construction Group is responsible for the construction of all of Placer Dome’s major projects and contributes to the development of most major feasibility studies. This group includes an international collection of Placer Dome people who have built mines in Papua New Guinea, Australia, Chile, the United States and Canada. This paper outlines the changing role of the Construction Group from the early days of single projects to today, when several projects are in various phases from feasibility to construction. The projects’ total annual budgets have from time to time exceeded one billion dollars. IntroductionAs the competition increases globally between the major gold mining companies, the impetus continues to build mines at the lowest cost with the shortest construction schedule. Placer Dome has more than met that challenge by building mines around the world at a pace that was not contemplated 15 or 20 years ago. Since 1960, Placer Dome has built 30 mines and expansions at a cost of nearly 4.5 billion dollars.In the last six years alone, Placer Dome has built 14 mines and expansions, worth 2.6 billion dollars. The company’s success is due primarily to Experience, Innovation, People and Standards.The diversity between projects, let alone the pace, has been a challenge. Placer Dome has built mines around the world in a variety of extreme climates and distinctive cultures. The construction experience gained from these projects has allowed Placer Dome to develop an extensive knowledge and data base making it easier to “fast track” projects.Through the years Placer Dome has developed a human resource base. It now has an experienced and adaptable core team of people able to set up construction projects and build mines anywhere in the world. By developing standards and systems to support the projects they can act as soon as a new project is approved, and complete the projects quickly and effectively. The result is that Placer Dome now has the construction expertise to build its own mines, giving them the competitive advantage that allows them to design and construct a mine in the least time at the lowest capital cost. This was demonstrated in March 1997 with the completion of the construction of two new mines in 12 months."

Jan 1, 1998

By Anil Saigal, Mark H. Shooter, Michael A. Zimmerman

Liquid Crystalline Polymers (LCPs) provide favorable dielectric properties for extremely high frequency (30–100 GHz) radio frequency device packaging and printed circuit board substrates. The material studied in this work is a proprietary, thermotropic LCP composite developed and manufactured by iQLP (Woburn, MA, USA). Dielectric constants measured in the flow direction of the post-processed materials differ between the two processes, 3.51 in injection molded plaques, and 4.23 in cast films. This investigation sought to determine the cause of process-induced variation in the dielectric constant between injection molded and cast film extruded LCP. The complex thermomechanical environment present during processing of LCPs creates a through-thickness hierarchical structure, simplified in this study as a skin and core layer. The volume fraction of skin layer of the post-processed LCP was determined to be the differentiating factor, and responsible for the difference in dielectric constant between the injection molding and cast film extrusion processes. The resulting dielectric constant is a function of this volume fraction with a near linear relationship.

Mar 1, 2017

By Elmer Peña Matta

Un estudio anterior sobre la mena Pb. Zn en la concentradora de Paragsha determinó que los finos encontrados en la alimentación de los molinos, se podía separar, evitando la remolienda y la alimentación directa del ciclón, para luego obtener los productos destinados a la flotación y molienda, respectivamente. En este sentido, el objetivo del texto, radica en mostrar los resultados del uso de los cedazos DSM en los molinos primarios, asi como el proceso de la adaptación del mismo. El acondicionamiento de los cedazos DSM es un proceso que permite recibir alimentación de una faja transportadora y descargar su cajón de alimentación original, que está diseñado para la descarga de la bomba. De forma que la aplicación de los cedazos DSM es factible en menas que no necesitan molienda, donde se aumenta la capacidad en el equipo de la molienda, se mejora la clasificación de los productos, y surgen nuevas perspectivas de incrementar la metalurgia, especialmente en especies friables. Asimismo la ubicación de un cedazo DSM varía de acuerdo a la necesidad, sea la entrada de molinos, ciclones, descargas de molinos de varillas, bombas con productos por clasificar, equipos de heavy medium, etc.

Jul 20, 1960

By Brent C. Jellicoe, Phil Robertshaw, J. Murphy, Peter Williamson

Kimberlites and associated diamonds have been the focus of extensive exploration in central Saskatchewan since 1988. During 1989, Uranerz Exploration and Mining Limited identified 71 shallow magnetic anomalies in the Fort a la Corne area from detailed aeromagnetic surveys. By the end of 1991, 18 of these targets had been proven, by drilling, to be kimberlite bodies encased within Cretaceous sedimentary strata. From 1991 to 1997, the number of drill-confirmed kimberlite bodies increased to 69. Our current view, drawing on an integration of geophysical and geological information, is that the kimberlites are composed of individual bodies and multi-vent clusters of coalesced bodies, all apparently constructed of stacked, temporally distinct layers of pyroclastic crater-facies kimberlite. Diamond recoveries and geochemical results from associated heavy minerals at Fort a la Corne remain highly variable, although continued minibulk sampling is expected to improve the estimation of diamond grades for the most prospective bodies.

Jan 1, 2001

By G Harbort

The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to convert spatial geological data into metallurgical information to drive production and mine planning, blast design, blending strategies and plant set-up. Increasingly the process designer is required to interface with geological and mining staff to propose the best investment strategy for a project’s benefit.The geometallurgical model development for the Zafranal copper-gold project commenced in March, 2010, several months after the start of a major drilling campaign by AQM Copper Inc. The initial evaluation stage required review of historical Teck RC data to determine areas of metallurgical interest within the project. As drilling transitioned from RC to diamond drilling, core that was considered representative of the resource was selected and subjected to MLA mineralogy analysis. When coupled with sequential copper analyses this allowed calibration of an assay derived mineralogy model, allowing process concept options and a preliminary test program to be developed. This Phase 1 test program provided a preliminary process design, operating costs and anticipated concentrate grades and recoveries. Both this data and resource estimation were used to generate a preliminary Whittle pit optimisation based on maximising net smelter return, which in turn fed into a preliminary mine plan. The preliminary mine plan, in conjunction with geological logs and core results was used to develop a phase 2 metallurgical test program, where variability tests were conducted throughout the resource and composites formed to investigate specific years of the mine plan in locked cycle flotation. In addition comminution tests were modelled against geometallurgical domains allowing comminution components values to be calculated for 36?000 m of core. A flotation geometallurgical model was developed and incorporated into the resource model allowing concentrate grades and recoveries to be estimated on a block-by-block basis.

Sep 5, 2011

Traditional vat leaching has been done on a batch basis, which involves loading the vats, leaching, drainage, washing, draining again, and unloading. As a result of these many steps and the attendent cost of labor, vat leaching is generally not an economic proposition. Also, like heap leaching, there is a tendency for channeling to occur within the bed, whether the leach solution flow is by percolation upwards or downwards. No doubt experimenters over the decades have been enticed by the idea of fluidization induced by upward flow through the ore bed. If the bed could be fluidized, then a continuous flow of material could be set up, dispensing with the high cost of loading and unloading the vat. A quick calculation of solution flow requirements, however, soon reveals that the volume of constant liquid movement necessary to sustain fluidization is prohibitive from a power and cost standpoint. The premise of the Mackie Vat Leaching Jig (MVLT) concept was that the large volume of liquid flow required for fluidization could be achieved instantaneously, and that during this small element of time, the solids would flow under the influence of the hydraulic gradient in the vat. If this procedure could be repeated in a cyclic manner, then a steady-state condition could be set up. Experiments in the laboratory demonstrated that solids flow could be achieved in this manner.

Jan 1, 1991

By Shengli Wu, Juan Zhu, Wei Huang, Xinliang Liu, Kaiping Du, Kaifa Zhang

Based on the furnace burden of high content of Al2O3, the process of softening and melting and the characteristic of primary slag were studied with the increase of MgO content in the sinter and adding some MgO into the pellet. The results showed that the content of MgO in the primary slag increased with the increase of MgO in the sinter and pellet. Meanwhile, the permeability of the furnace burden was improved because of low viscosity of high MgO primary slag. Compared with the increase of MgO content in the sinter, the increase of MgO content in the pellet can improved the softening and melting characteristic of the comprehensive furnace burden more effectively. More Mg-bearing pellet should be chosen in the comprehensive furnace burden for the purpose of improvement the fluidity of primary slag and the permeability of the furnace burden in the burden of high Al2O3 content.

Jan 1, 2015

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By Rodney R. Krause

In attempting to tell the general public about the coal industry's land reclamation efforts, we have often said, "We're not doing things by the book, because we're still writing it." Like any good catchphrase, the statement is not only striking but true. It is particularly true in the mountains of Appalachia, where the problems of mining; and of reclamation are made more intense by the nature of the terrain. Mining and reclaiming the land "by the book' --which is to say by the methods of contour mining traditionally used in hill country--hasn't worked too well. So a lot of conscientious coal operators and associations are trying new methods--new ways of mining, new machines for seeding and planting, and new species to seed. Not all their experience can be transplanted to other areas, and of course I don't believe that Appalachia is the only place where new methods are being developed. Nevertheless, there's enough action in Appalachia to make a detailed examination rewarding, so let's focus on the hills to see what's new.

Jan 1, 1970

By P. Bevilacqua

In this paper the possibility to complete the copper recovery and to enrich in PVC a mixture of plastic granules obtained by grinding electrical cables are investigated. The recovery of a large part of the copper still present among the plastic granules was possible by means of a mechanical screening, the finer polymeric fraction was collected, at the same time. In order to complete the copper polymer separation the following techniques were employed. Counter current separation in water, static dense medium separation with zinc chloride solution and copper extraction with nitric acid and subsequent electrolytic deposition. A Tri-Flo® dynamic dense medium separator was employed in order to separate the lighter polymeric fraction, from the heavier polymeric fraction, mainly PVC. Water or a salt-water solution was employed to feed the separator device.

Jan 1, 2014

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927