Search Documents

By Wiechers HNS

In China the hydrogeological type of solid mineral deposits can be divided into A. Mineral deposits with fissure water; B. Mineral deposits with pore water; and C. Mineral deposits with karst water. The hydrogeological conditions of mineral deposits with fissure water are relatively simple with the exception of a few cases. Mineral deposits with pore water are few but great amounts of ground water can be encountered in the mine accompanied by floating sand or slope failure during the exploitation. Mineral deposits with karst water are complex in their hydrogeological conditions. Enormous inrushes occur frequently in the mines of north China; Karst collapses are a serious matter in the mines of the south; Subterranean river and conduit systems are often encountered in the southwest. This paper will give full discussion on these features and put forward a way of combating and controlling the groundwater problem in accordance with type and feature.

Jan 1, 1988

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

By S Johnston, L Howe, S Stevens

Regulators have an important role to play in fostering and enabling reliable, effective, environmental management. Given this, it is perhaps surprising that there has been relatively little debate on exactly how regulators can enhance their own approaches, in order to promote improved outcomes overall. The authors argue that applying research on High Reliability Organisations, as well as the University of Pennsylvania’s Penn Program Framework for Regulatory Excellence, to regulators has the potential to facilitate positive environmental results across the mine life cycle.

Aug 2, 2023

By Bingguo Liu, PENG LIU, Haigang Dong, Jinhui Peng, Libo Zhang

Parameters of technique to decarburize from spent petrochemical catalysts via microwave oxidation roasting were investigated. Decarburization process was performed on a microwave heating system. The results showed that the decarburization percentage of spent petrochemical catalysts was significantly affected by roasting temperature and sample thickness in the range studied. The decarburization percentage was 99.5% in microwave fields under the optimized conditions, roasting temperature 600 °C, roasting time 40 min and sample thickness 2 cm respectively. The residuum after microwave decarburization was characterized by field emission scanning electron microscopy (FE-SEM) which showed that the deposit carbon had been removed effectively.

Mar 1, 2017

By Kurt Wiener

A major process control system is in some ways like a complex organism. The extremities, (that is, field instruments) are exposed to many hazards and suffer malfunctions of relatively minor and repetitive nature. Here I equate a stuck valve or dead transmitter with a skin abrasion or cut. The maintenance and repair of the extremities can be done by technicians with basic but thorough knowledge of relatively few problems and their solutions. Here I equate with administering Band-Aids and aspirin. On the other extreme, when the master control device (such as a computer) fails, one does not attempt home remedies. A "brain" specialist is called in. It is, however, crucial that the patient be able to clearly describe his symptoms. Getting down to the case at hand, a complex system consisting of field instruments, instrument racks, interface equipment, and perhaps a computer, may require maintenance at all levels. At the field equipment end where physical damage, corrosive atmospheres, reconfiguration, and routine calibration checks are common, the customer has the opportunity to develop a competent staff of maintenance people. The relatively high maintenance activity assures competence through repetition.

Jan 1, 1980

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

By J. J. Shields

This is the Seventh of a series of publications that describe methods and practices used in mining bituminous coal mechanically.3/ This report deals with the operation referred to in coal mining as continuous mining, and the interest shown by mining companies in this method is the reason for this study. Only continuous mining as it applies to the room-and-pillar system of mining, or a modification thereon, is discussed in detail in this report. Although not always as continuous as the name implies, it is a system of mining in which a machine is used to cut and load coal in one continuous operation without drilling and blasting the coal. With the mining equipment in most general use today, the usual cycle of operation in mining of coal is: (1) Timber, (2) cut, (3) drill, (4) blast, and (5) load. As the phases of this type cycle cannot be performed simultaneously in the same working place, it is necessary to operate from 3 to 7 working places so that at least 1 place is available for coal loading at all times. Even if the schedule of the phases in a cycle is maintained, coal production ceases during the time required to move the loading equipment from one loading place to the next. In 1920 a continuous-type mining machine4/ was installed in an Illinois coal mine to drive entries. Several other companies used these entry drivers for short periods in the following few years. In 1927 a southern Illinois coal company installed 2 of these machines which, in the next 25 years, were reported to have driven over 200 miles of entries. The machines did not attain widespread usage.

Jan 1, 1954

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth&apos;s crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.&apos; The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson&apos;s paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson&apos;s statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By A. Sokolov, M. Demsky, E. Hasikova, V. Gostilo

"Previously, we upgraded and implemented two gamma activation assay (GAA) systems designed to analyse the gold content in raw ores at Zarafshan laboratory, Uzbekistan, and achieved a detection limit of less than 0.05 g/t under actual industrial conditions. Having started to design a fully modern, industrial GAA system for mining companies, this paper analyses the advantages, disadvantages, and special features of all major system components that can influence the sensitivity and accuracy of the analysis. The results of a study to optimize the detector geometry and sample size are presented and the performances of the linear electron accelerator, detector array, and sample transportation system of a modern, industrial GAA system for analysing gold, silver, and rare earth elements are considered. IntroductionGamma activation analysis (GAA) has considerable potential as a future replacement for traditional fire assay analysis in gold mining (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017). The essence of GAA is to irradiate ore samples with high-energy gamma quanta generated by an electron linear accelerator (LINAC) and then to use a gamma spectrometer to detect the induced activity of the excited gold nuclei. The advantages of this method are discussed in detail elsewhere (Hoffman, Clark, and Yeager, 1998; Morse, 1977; Bourmistenko, 1986, 1981; Sammut, 2016; Tickner et al., 2017), where it is shown that GAA is uniquely suited to analysing ore samples when mining for gold, other precious metals, and accompanying elements.These advantages were realized in three industrial GAA laboratories that were commissioned in Zarafshan, Uzbekistan in 1977, in Magadan, Russia in 1979, and in Batagay, Russia in 1986 (Bourmistenko, 1986; Nii Tekhnicheskoy Fiziki I Avtomatiki, n.d). In 1989, a fourth industrial GAA laboratory was commissioned at a gold mine in Tommot, Russia. However, the project was subsequently halted due to economic reasons (Moshkov and Tjamisov, 2017). Currently, only the laboratory of the Muruntau mine in Zarafshan, Uzbekistan is in operation. The gamma activation method for gold determination is widely applicable at this mine owing to its high productivity and low cost of analysis. An outstanding aspect is the performance of more than one million analyses per year."

May 1, 2019

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By K. Bunney, R. Pleysier

The deportment of a suite of elements through representative gold ore processing unit operations in cyanidation has been investigated. Chromium and lead are not soluble in alkaline cyanide solutions. Arsenic, antimony, cobalt, molybdenum, selenium, tellurium and vanadium are soluble, but typically do not adsorb onto activated carbon to any appreciable extent. Silver, copper, cadmium, mercury, nickel and zinc to varying extents report along with the gold to the carbon eluate. Cadmium, mercury and zinc can report to the carbon regeneration kiln off-gases. Strontium is soluble and adsorbs on carbon where it remgins.

Jan 1, 2011

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By G. E. d’Aquin

Sources of sulfur have varied based on technology and societal needs. It has been mined in its elemental form for centuries. Twentieth century technology brought thermal mining (Frasch, 1894) to the forefront of sulfur extraction. Then, by the 1980s, petroleum processing generated almost 40 percent of the 50 Mt (55million st) of sulfur in all forms (SAF) produced in the world. Metals processing (the reclamation of effluent gas by various means as “sulfur in other forms,” or SOF) followed at 30 percent of all sulfur values produced and then Frasch at 22 percent. Petroleum and gas processing now generate most of the elemental sulfur produced in the world. Single Two Frasch mines remain, one each in Iraq and Poland. Conventional mining of small to insignificant volumes also survives in Russia, Latin America and Indonesia. The volume of “recovered” sulfur (the name commonly given by the industry to hydrocarbon-derived material) generated will increase faster than energy consumption as oil and gas with greater amounts of sulfur are used and environmental restrictions on the sulfur content of the fuel consumed become more stringent.

Jan 1, 2005

By Steve Kral

Despite low commodity prices and mining industry cutbacks throughout the world, Peru remains one of the industry’s bright spots. The country’s remarkable economic turnaround during the 1990s remains a model for other developing nations to follow. And the Peruvian government has not forgotten the industry that was instrumental in that turnaround. True, the country has not been spared the effects of the mining industry’s retrenchment that has occurred in other parts of the world. However, foreign mining companies remain committed to doing business in Peru. And the government remains committed to attracting foreign investment and maintaining a strong mining industry. This commitment was evident in September 1999during the 24th Convention of the Institutos de Ingenieros de Minas del Peru in Arequipa, Peru. More than 3,000 mining industry professionals from around the world attended the convention. And Extemin, the accompanying exhibit, featured more than 450 companies, many from the United States, Canada, Australia, South Africa and other countries.

Jan 1, 2000

By G. Y. He

The large-scale 8.53m×3.96m (28?×13? F/F) SAG mills was first applied in Donggua Hill Copper Mine which processes 13,000 tons ore per day. The crushing and grinding circuit went into operation in the Donggua Hill plant in October 2004. However, at the beginning, the productivity of grinding only reached 58% of the capacity expected and some indexes of the crushing and milling circuit didn?t meet the requirements. Especially, the total load of the 8.53m×3.96m (28?×13? F/F) SAG mills was up to 34%~41% (25%~30% designed)and some hard rocks with the size of 25~70mm, which can?t be treated as a medium or even would be crushed and make larger ores or steal balls necessary, were seriously accumulated in the SAG mills. Consequently, they occupied the effective mill volume which in turn reduced the efficiency of the SAG mills and increase the energy consumption. In order to solve the problem of accumulation in the SAG mill and increase its productivity, some measures were taken, such as passing more hard pebble through the grate at mill dis-charging end, changing the type of steal balls and so on. And the results showed that these measures functioned well and had good effects, which is that the filling percentage of the SAG mills has been reduced to 26%~29% from 34%~41% with the composition of particle sizes improved a lot and the productivity increased by 77.4% reaching up to 13,380 tons per day.

Jan 1, 2014

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating." The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942