Search Documents

By Baogui Yang, Jie Yang, Anthony Iannacchione

"The cemented coal gangue-fly ash backfill technique (CGFB) has commonly been used to control subsidence damage caused by underground coal mining. This paper discusses the CGFB backfilling process used at the Xin-Yang coal mine, Shanxi Province, China. A general description of the components of the CGFB are provided. The reaction of the strata to the backfilling process is simulated with a scaled physical model based on the Xin-Yang conditions and verified with subsidence points on the surface. With the help of the cemented filling materials, the CGFB produces only a slight bend to the overburden roof strata over the longwall panel. Physical models were constructed at the China University of Mining and Technology, Beijing, to simulate actual conditions. The modeling results show minor fracture distribution in the overlying strata and lower abutment pressure development within the backfilling area. The effectiveness of the CGFB technique is verified by a reduction in the vertical surface subsidence measured above the backfilled area.INTRODUCTIONUnderground longwall mining is the most efficient underground means to recover coal resources and is used widely in China, the US, Australia, and Europe. However, this type of mining has introduced some serious environmental impacts. Perhaps the most significant environmental issues are the surface and groundwater impacts associated with the formation of the subsidence basin (Bell and Donnelly, 2006). Backfill technology has been used for years to mitigate subsidence impact. Simply speaking, the backfilling technique places filling materials into the void left from the extraction of coal. When this material is placed within the gob, it is capable of partially supporting the overburden until a new equilibrium is reached. Essentially, the backfill material inhibits crack development and expansion caused by the strata movement and mitigates damaging ground deformations.The cemented gangue-fly ash backfill (CGFB) is one type of novel backfill technology, consisting of cement, coal gangue, fly ash, water, and additives in varying concentrations. The CGFB is mixed on the surface, pumped underground through a pipeline as a slurry, and placed in the void behind the longwall shield under the protection of specially designed hydraulic supports."

Jan 1, 2018

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By A. I. Arol

Bentonite is an important industrial mineral with very wide application areas. Its unique colloidal, swelling, thickening and adsorption properties make it a useful agent in drilling, metal casting, and iron ore pelletizing, environmental, food, cosmetics, pharmaceuticals and many more industries. Because of its swelling property, bentonite suspensions can only be prepared at rather low solid coentrations, i.e. 8-10%. In order to process bentonite in slurries with high solid content, it was thought that a non-polar organic solvent, instead of water, can be used. Not only large amounts of bentonite can be dispersed in organic solvents but also the solvents may be regenerated. The bentonite obtained through such a process must either equal or better properties than those of untreated bentonite. In this study, the effect of organic solvents such as acetone, methyl-ethyl ketone and n-haxane on the main properties of bentonite, such as water adsorption and rheology, was investigated. It was found that bentonite can be dispersed in the mentioned organics in large quantities with no loss of quality. Keywords: bentonite, montmorillonite, water adsorption, industrial minerals

Sep 1, 2012

By R. J. Enkin

Modern mineral exploration depends on multidisciplinary 3-dimensional integration of geological and geophysical data. Identification of the geological sources of geophysical anomalies requires knowledge of the physical properties fingerprint of rock types, formations and their alteration products. Understanding how and why rock physical properties vary within the Earth's subsurface ensures that appropriate geophysical exploration methods can be chosen, and allows for more efficient and effective surveys to be designed. Physical properties knowledge is integral to geophysical modeling - measured data or values estimated based on geological understanding are used to produce realistic forward calculations and to constrain inversion models. Mira Geoscience and the Geological Survey of Canada, in collaboration with industry and academia, are building a Rock Properties Database System (rpds.mirageoscience.com). It compiles the most valuable physical properties for mineral exploration (density, porosity, magnetic susceptibility and remanence, electrical resistivity and chargeability) linked with location and lithological metadata. A critical knowledge gap, addressed in this study, concerns the dependence of physical properties on alteration and mineralization processes. We report on the results of a collaborative University of British Columbia - Geoscience British Columbia project, ?Integrated Geological & Geophysical Porphyry Models: Adding Value to Geoscience BC Geophysical Data?. As part of the QUEST and QUEST-West geophysical initiatives, Geoscience BC focused detailed geophysical surveys on a suite of six known porphyry deposits: Mount Milligan, Endako, Huckleberry, Bell, Granisle, and Morrison. Physical properties for a set of 269 samples of characteristic host rocks and their altered equivalents were measured. The causes of physical properties variations were investigated through their correlations with ore and alteration mineralogy determined from thin-section observations and X-ray diffraction analyses. Physical properties of variably altered host-rocks and intrusive rocks vary significantly between different BC porphyry deposits. No specific unifying geophysical model exists that can be uniformly applied during exploration. Knowledge of local background geology and local physical properties variations is necessary as host-rocks and intrusive rock compositions vary depending on magmatic affinities, and alteration styles will vary reflecting host-rock compositions, crustal depth and influence of meteoric water. A district-scale exploration strategy requires location of intrusive bodies, which are commonly magnetic, resistive and low in density. Correlations should not be expected between density and magnetic susceptibility, because alteration may lead to magnetite destruction or to secondary magnetite development. Deposit-scale ground geophysics might image potassic alteration zones that can be magnetic in both alkalic and calcalkalic systems. Low magnetic susceptibilities, resistivities and densities might aid in locating the typically more porous phyllic and argillic zones. All geophysical data must be interpreted with background knowledge of local rock types and in light of the expected deposit model and associated magmatic and hydrothermal processes. The most effective means to building physical properties knowledge prior to geophysical investigation remains collecting rock physical properties measurements. The cost of rock properties data collection is low, relative to the overall costs of running a mineral exploration program, and can provide an important framework for design of geophysical surveys, survey method selection, geophysical modelling, and data interpretation.

Aug 1, 2013

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By Lon Santis

This paper analyzes 110 serious accidents that occurred during the use of commercial explosives in mining, construction, and other industries since 1992. Data from the Mine Safety and Health Administration (MSHA), the Institute of Makers of Explosives (IME) members’ reports, and media reports were used. Only accidents that resulted in a fatality, significant lost work time, or injury to the public were considered in this analysis. The accident data were analyzed for trends in frequency, type of industry, cause, type of individual harmed, and geographical region. Although the data showed that explosives accidents are decreasing in frequency, still, 29 people were killed and 134 injured. Eightyfive of the accidents occurred in mining, 17 occurred in construction, and 8 occurred in other industries including oil recovery, seismic exploration, agriculture, logging, boiler cleaning, and avalanche blasting. As other studies have shown, flyrock and failure of blast area security caused over half of the accidents. Mishandling, misfires, or fumes caused just over one-third of the accidents. Lightning and drilling into explosives were responsible for the remainder of accidents.

Jan 1, 2003

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

By G. L. Oldright, Virgil Miller, F. K. Shelton, Keck. W. E., Horst Sieg

Potash is one of the principal foods and is necessary for the growth of most vegetables, grains, and fruits. For many years, this country depended entirely upon foreign sources for its supply of potassium compounds. However, during the last 15 years the domestic production of potash has gradually increased, as shown in table 1. 7/ Imports now supply only half of the American market. In 1936, the equivalent of 207,000 tons of K20 was imported, and 210,000 tons was produced domestically. In 1935, domestic consumption was approximately 420,000 tons of potash, a 57 percent increase over that for 1934 and surpassing previous peaks of 1928 and 1930.

Jun 1, 1937

By G. C. Wallick, J. S. Aronofsky

This paper presents an experimental verification of numerical solutions of the differential equation describing the transient flow of an ideal gas through a porous material including gas slip effects. Several experiments previously proposed by one of the authors are described together with the correlation of the experimental results with the numerical solutions. Excellent agreement is shown between experiment and theory, thus demonstrating the validity of both the basic assumption made in the derivation of the differential equation and of the numerical solutions of the differential equation. INTRODUCTION In a recent paper,' one of the authors has discussed a numerical solution of the differential equation describing the unsteady flow of an ideal gas through a porous material. This paper was primarily concerned with the effect of gas slip on the flow behavior. In steady state measurements, Klinkenberg2 and others have observed that the apparent gas permeability Kn of a porous material may be expressed as a linear function of the reciprocal average pressure 1/P of the form, ka = b + m/P........(1) where the intercept b is a constant for a given porous material and the slope m is a constant for a given porous material-gas combination. Aronofsky1 assumed that Equation (1) could be used to describe transient flow if P was replaced by the average pressure in an infinitesimal volume element. A number of numerical solutions of the resultant differential equation were presented and specific flow experiments were proposed as a means of testing the numerical solutions. The purpose of the present paper is to describe the results of several of these experiments and the correlation of the experimental data with the results of the numerical analysis. Reference should be made to the previous paper' for details of the mathematical and numerical analysis. EXPERIMENTAL PROCEDURE A simplified schematic drawing of the experimental apparatus is shown in Fig. 1. An 8.89 cm diameter limestone core of length L = 14.82 cm was mounted in a conventional rubber sleeve permeameter cell. The external sleeve pressure in this cell was maintained equal to 500 psig during all experimental tests, thus permitting only longitudinal flow through the core. One end of the core, X = L, was connected to an adjustable cavity of volume V as well as a pressure gauge or manometer. The other end of the core, X = 0, was connected to a Nullmatic pressure regulator which was in turn connected to a nitrogen cylinder or vacuum pump. In each experiment, the core and adjacent dead volume were charged with nitrogen to a uniform gas pressure P1. The pressure at X = 0 was then suddenly raised or lowered to a constant pressure P, and the resulting pressure buildup or pressure decline at X — L was recorded as a function of the time. The porosity + and the permeability constants m and b were determined using the transient method which was suggested by the results of the numerical analysis and which was described in the earlier paper.' The following average values for these constants were obtained as a result of 19 separate evaluations: 171 -0.259 2 0.005 md-atm; b = 0.374 5 0.008 md; and F = 0.098 ± 0.005*. It should be noted that in order that transient phenomena will be slow enough to be observed conveniently, it is desirable to use a porous material of very low permeability, e.g., less than I md. Moreover, it is in this low permeability range that the gas slip effects are most significant. Thus, such a low permeability sample is very suitable for use in an experimental verification of the numerical solutions previously described.

Jan 1, 1955

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By Albert Burch

The theory of the present law with reference to lode locations contemplates the existence upon the surface of mineral-bearing veins which have clearly marked boundaries, and which can be so readily traced that a locator may immediately mark the boundaries of his 600 by 1,500 ft. claim in such a way that the vein will 'pass through both of its end-lines. It also supposes that, having discovered such a mineral-bearing vein, the locator will at once post a notice upon such discovery, mark the boundaries of his location in such a manner that they can be readily traced, and from that time forward have absolute title to the ground embraced within such boundaries, as against every person except the United States. For initiating title to placer ground, the law presupposes the discovery of a valuable mineral deposit; but not necessarily in place, as in the case of lode claims; and the location must be made to conform "as nearly as may be" to the legal subdivisions of the United States public land survey. When the placer law was extended to include the acquisition of title to oil lands, no exception was made as to the necessity for the discovery of valuable mineral in advance of location! Practice under the Present Law Nature did not make all veins clearly defined and readily traceable upon the surface; nor did she, in all cases, leave upon the surface which overlies important ore bodies such outcrops as would in them-selyes be considered valuable; and the citizen of the United States has in the past endeavored to steer his course between the mandates of the law and the limitations of nature. Until quite recently, it has been possible to obtain a patent for any-

Jan 1, 1915

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By Sushant Upadhyaya, Deniz Karadeniz, Ahmed Mohamed

Soil setup analysis provides opportunities for efficiencies in pile foundation design and installation. Soil setup gain with time was evaluated as part of the foundation design and installation for twelve bridges along the Interstate 64 corridor between York County and Newport News in Virginia. The substructure elements of the bridges consist of driven precast prestressed concrete piles or H-piles. This case study describes lessons learned to understand the soil setup phenomenon during the installation of the piles in coastal plain. We were able to make expedited decisions during construction by analyzing previously performed pile dynamic analyzer (PDA) test results within the project alignment. Data evaluation included analyses of PDA data obtained from initial driving and restrike after a few hours to 5 weeks. The test data showed pile resistance increase up to twice in most cases and as high as four times in some cases. Foundation design and acceptance based on soil setup can provide opportunities for cost savings and advanced scheduling during construction.

By W. F. Dietrich

Mineral fillers are relatively inert chemically under the conditions of use but have physical properties* that modify those of the materials • The properties. uses, and other data on 15 classes of important *The pro listed in the second edition of Industrial Minerals and Rocks.l A third edition of this reference is in preparation. in which they are incorporated. The mineral fillers considered in this article are asbestos, barite, clays, diatomite, crushed limestone, limestone whiting and lime, mica, silica, talc and soapstone, and pyrophyllite. Slate and stone, other than limestone and its derivatives, are excluded because, even though used in large quantities, they are exceptionally low-cost materials generally produced close to the area where they are used. Carbon black is excluded because it is manufactured from natural gas and more than 90 pct of the output is used in rubber; hence the factors for estimating requirements are easily evaluated. OVERALL GROWTH FACTORS Table I gives the population, retail sales, and value added by manufactures in the U. S. and in the eleven western states in 1954. These data are rough guides to the proportionate part of total U. S. markets for products containing mineral fillers that may be expected in a given area. For example, the population of the eight Mountain states in 1954 was 3.6 pct, and retail sales in these states were 3.8 pct of the U. S. total, but the value added by manufactures was only 1.3 pct of the U. S. total. On the other hand, the three Pacific Coast states, with 10.3 pct of the total population, had 12.0 pct of the retail sales and produced 9.6 pct of the value added by manufactures. On an industry-by-industry basis the correlation between the three guideposts will not be as close as shown in the 1954 data for the Pacific Coast states, but in the long-term view the continuing rapid population growth in the western states is certain to result in expanded industrial production at an even more accelerated pace, which will shorten the gap between local consumption and production in most major groups of manufactured consumer goods. Of course, there will always remain favorable areas for production of specific products. Such special situations must be individually analyzed. Fig. 1 compares the population trends in the U. S., the western states, and California with Real Gross National Product from 1910 to 1957, with forecasts to 1970. It is estimated' that the U. S. Real Gross National Product, as measured by the value of goods and

Jan 1, 1960