Search Documents

By A. Simkovich, R. W. Lindsay

The possibility of using sodium sulfide slags to remove copper from ferrous alloys has been investigated by Jordan1 and by Langenberg.2, 3 In these studies, such slags were determined to be capable of removing copper and sulfur from the melt. The present work represents additional effort to clarify the effects of temperature on copper removal. The experiments were performed in a 17-lb induction furnace. Graphite crucibles contained the melts and kept the baths saturated with carbon. Temperatures were measured with a calibrated optical pyrometer and were controlled by manipulation of power input to the furnace. Estimated accuracy of temperatures in this investigation is ± 10°C (18°F) for measurements prior to slag additions, and + 20°C (36°F) after slag formation. The procedure consisted of melting 800 g of electrolytic iron. During this step, powdered graphite covered the exposed iron surface. After a predetermined temperature was reached, copper shot was added. A sample of the molten alloy for chemical analysis was then aspirated into a silica sheath. Next, a slag-forming mixture of sodium sulfite and graphite was added instantaneously to the melt. The sodium sulfite amounted to one-tenth the charge weight of iron; sufficient graphite was added to combine with oxygen in the sodium sulfite, assuming formation of carbon monoxide and reduction of the sulfite to sulfide. Subsequent to the slag addition, the molten alloy was sampled periodically, with the exception of heat A in which no intervening samples were taken between the slag addition and the end of the run. The iron was poured into a graphite mold, and the ingots sectioned and drilled for samples. Results of selected heats are presented in Table I. Analyses of samples drawn from the iron prior to slag addition are listed under zero time. Two samples from heat D were reported with copper contents greater than the initial concentration in the bath. Owing to the gradual but complete disappearance of slag during this heat, it is believed copper momentarily became more concentrated in the upper portion of the bath while reverting from the slag. This is the region from which samples were drawn. It should be noted that analysis of the ingot was equal to the copper content at the time of slag addition. The terminal temperatures of heats D and E, and the initial sulfur content of heat A are also to be noted. Because of the large temperature drop which occurred when slag was formed in heat D, power input to the furnace was increased in heat E after the slag addition, causing a higher terminal temperature. In heat A, the initial sulfur concentration was relatively high as compared to heats B through E owing to contamination by some slag remaining in the crucible from a previous heat. It is evident from Table I that copper was removed at the onset of slag formation. Roughly 30 pct of the copper was taken into the slag, with the exception of heat D, which had approximately 50 pct removed. For a comparatively short time of slag-metal contact, it appears that no gain is to be made in copper removal through use of high or low temperatures. If the slag initially formed remains in contact with the iron for an extended period, temperature has a marked effect upon copper removal, as can be seen by studying results for the two extremes in temperature. At about 1425°C, the copper level remained relatively constant after the initial removal by the slag. However, in the region of 1670°C, a definite reversion of copper occurred. Reversion was incomplete in heat D, and complete in heat E. The final temperatures of heats D and E differed by about 75°C. This temperature difference is thought to be the reason for only partial copper reversion in heat D. It is believed the effects of temperature noted above are related to the evolution of a white fume, which appeared in every run except heat A. (In the case of heat A, the fume was practically indiscernible.) After each slag addition, a yellow flame formed for about 5 sec. When the flame subsided, a white fume appeared. Upon contact with surrounding cooler surfaces, this fume deposited as a white solid. In the experiments made at 1425°C, evolution of fume continued unchanged to the end of the runs. However, heats D and E exhibited a different behavior. A very noticeable decrease in fume evolution from heat D was observed. Furthermore, this heat had much less slag remaining than did runs A through C when the experiments were terminated. No slag remained at the end of heat E; evolution of fume from this heat ceased prior to pouring. Spec-trographic analysis of the white deposit indicated sodium to be the major metallic element, with the maximum concentration of iron and copper as 0.1 and 0.01 pct, respectively. It is supposed the white fume observed in these experiments is principally sodium oxide (Na2O), formed by oxidation of sodium in the slag and subsequent sublimation. (Sodium oxide is a white to gray substance in the solid state; at 1275oC, it sublimes.4) According to this mechanism, elevated temperatures would accelerate removal of sodium from the slag, sulfur pickup by the

Jan 1, 1961

By P. C. Tully

The vapor pressure-temperature relationships for saturated pure liquid nitrogen are calculated by the Strobridge equation using a digital computer. This information is presented in two tables: first) in pressure increments of 0.1 psi from 1.8 to 492.9 psia) and second) in temperature increments of 0.1° from 63.15° to 126.26° K. These tables should facilitate the calibration of temperature-measuring devices over this temperature range.

Jan 1, 1967

By Marcella Gautê Cavalcante Xavier

As ligas livres de chumbo (Lead-free solder alloys) potencialmente utilizáveis em processos de soldagem branda, tais como as ligas à base de Sn, vêm sendo estudadas como alternativas para substituir as ligas do sistema Sn-Pb. Em vista disto, o presente trabalho, aborda tanto a análise das características microestruturais formadas durante a solidificação transitória das ligas eutética Sn-0,2%Ni e hipereutética Sn-0,5%Ni, quanto a determinação das suas respectivas correlações com os parâmetros térmicos de solidificação: velocidade da isoterma eutética (VE) e taxa de resfriamento (?E). Para tanto, as ligas foram solidificadas unidirecionalmente no sentido vertical ascendente e em regime transiente, e caracterizadas por técnicas de microscopias ótica e eletrônica de varredura. Na liga hipereutética Sn-0,5%Ni, o aumento da quantidade de Ni na liga influenciou tanto o comportamento térmico quanto o espaçamento celular (λC), proporcionando maiores valores de ?E, porém, λC mais grosseiros.O intermetálico NiSn4 formou-se na região eutética de ambas as ligas, enquanto que na liga Sn-0,5%Ni, as fases primárias identificadas por EDS-MEV foram NiSn4 e Ni3Sn4. A transição morfológica celular/dendrítica(?E> 1,2ºC/s) ocorreu apenas para a liga eutética, enquanto que as células regulares da liga hipereutética deram origem as células do tipo placas(?E> 1,4ºC/s).

Oct 30, 2017

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Steve Kral

The mining industry in northern Ontario is known mostly for its huge nickel deposits. Inco’s and Falconbridge’s nickel mines in the Sudbury Basin are the best known. And with nickel prices being what they are, interest in the region continues. And how. Inco and Falconbridge want to merge. Teck Cominco wants Inco, but without Falconbridge. Xstrata made a hostile bid for Falconbridge, which Falconbridge rejected. And, in June, Phelps Dodge trumped them all when it made an approximately US$40-billion friendly offer for Inco and Falconbridge in a two-part deal.

Jan 1, 2006

By JAMES GAYLE

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1905.) IT is to be regretted that the data respecting the use of dry-air blast, which was presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should. have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. In the discussion of the paper it would appear from the conclusions of some participating therein, that they have been placed at some disadvantage in considering the economies obtained through the use of dry-air blast, by reason of the data covering such a short period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs, and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natural air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jul 1, 1905

By M Watson, A V. Engelbrecht, E Murray-Hayden

Whereas mine reconciliation is a well-established month-end process for most modern mining operations, the resource sector has yet to endorse uniform reporting factors against which model accuracy and metal recovery can be formally assessed. Logically, any comprehensive reconciliation framework should facilitate comparison between period reserve, mine and mill and production figures. Historically, Parker’s F Series ratios (Parker, 2012) are often used in some form by mine operators, although they are rarely shared externally, as formal definitions have yet to be accepted. This paper presents a structural extension to the reconciliation process, wherein resource ratios (R Series factors) are used to quantify the long-term impact of the information effect, together with dilution and ore loss. A case study from the El Limón Guajes (ELG) Mine Complex in Mexico is used to demonstrate how an R Factor Series can be implemented to facilitate operation optimisation, over and above conventional F Series reconciliation treatments. This approach is applicable to any mining operation.

Mar 22, 2022

By A. T. Visser

"SynopsisAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads was conducted in South Africa. This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential.These principles have been implemented worldwide, and it is useful to review the lessons learned. The objectives of this paper are to present a critical review of the status of mine haul road design and management, and the impact that these principles have made on operations, particularly the cost-effectiveness. The paper briefly reviews the principles of the haul road design and management and the extent to which they are applicable. Case studies of a number of implementations are presented to demonstrate that the principles are sound and have been applied effectively. For example, at an international operation the transport cost of coal was 40% more expensive than anticipated in the feasibility stage, and this made the mining operation uneconomic. Correction of this problem resulted in a viable enterprise. Although designed for opencast operations, the principles are equally valid for underground operations, and initial development work will be discussed.The main conclusions are that the research approach is valid and its effectiveness has been demonstrated in a number of applications. The anticipated financial benefit has been derived, and has made the mining operations that used the principles more effective. Of major importance is the application of opencast haul road design principles to the future thrust of using driverless vehicles in opencast and underground mining, where the road quality is not negotiable as there is no driver that can avoid obstacles or severe road deterioration.IntroductionAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads in South Africa (Thompson and Visser, 1996a, 1996b, 1998, 1999, 2000a). This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential."

Jan 1, 2015

By C. W. Davis

There are four parts to this circular and, respectively, they list firms in the Eastern (pp. 5-8), Southern (pp. 9-10), Central (pp. 11-15) and Western (pp. 16-22) United States and Provinces of Canada. Before listing the laboratories and the work performed there, it is proper to make clear what is done and what is not done by Federal bureaus, States, and Territories, as well as by Canada and Mexico. FEDERAL Bureau of Mines. - The Bureau of Mines does not make assays, analyses, or tests for individuals or firms unless they be incidental to investiga¬tions that are of possible benefit to the entire mineral industry. All significant results obtained in this way are made public through published reports. Any mineral sample sent to this Bureau for simple identification will be subjected to a cursory examination.

Jan 1, 1938

By T Walton, C Perring, M Pepper, G Gerber

The Yandicoogina Channel Iron Deposit (CID) is an accumulation of iron pisolites cemented by a goethite-rich matrix. The Yandicoogina CID’s are found in a palaeochannel that meanders within a broad structural basin of the Yandicoogina Syncline in Pilbara region of Western Australia. RTIO Yandicoogina Mine Geology team contributed to a number of strategies maximising the iron ore reserves mined by Rio Tinto. Two strategies are discussed: the replacement of the Batter-Berm final pit walls by contour dozing; and upgrading the lower grade material to crusher feed. 1. Contour dozing – traditional Batter-Berm pit final wall configuration left kilometre long wedges of ore sterilised around bench margins. Contour dozing final walls (ie dozing of ore down the ore-waste contact) as internally defined by RTIO Yandicoogina Mine Geology (Mine Geology), enabled recovery of additional crusher feed. 2. Upgrade of lower grade material – the lower ore domain (GVL) within the Yandicoogina orebody contains numerous clay pods. Contaminant Al2O3 inherent within clay pods can result in CID material outside of crusher feed grade specifications, causing it to be flagged as ‘internal waste’ in mining models and permanently lost to waste dumps. In 2011, after multiple tests, Mine Geology demonstrated that this material could be upgraded to crusher feed via wet processing. With the support of the RTIO Metallurgical Development team new grade specifications were defined. The resulting material has been used to supplement higher grade ore. While increasing the mining ore output, these ongoing value-adding strategies also promote more sustainable mining via better use of the non-renewable iron ore commodity. The initiatives extend mine life, reduce waste movement, improve strip ratio and increase productivity

Mar 22, 2022

By A Hall, D Kratochvil, P Littlejohn

Economic recovery of gold from complex gold ores, including poly-metallic deposits, is impacted by the presence of cyanide-soluble base metals. These base metals can create both a metallurgical challenge plus waste handling and disposal challenges. Base metals such as Cu and Zn compete for the cyanide reagent and often increase the total cyanide consumption to the point of making precious metals recovery uneconomic. In addition, the accumulation of base metals in cyanide solutions represent a challenge for cyanide detoxification and waste water treatment as these metals report to waste sludge. Such sludge requires safe handling and disposal, with possible long-term liabilities.Base metal interference can be removed with sulfidisation-acidification-recycling-thickening (SART) process technology. SART liberates the base metal from the cyanide complex and precipitates the metal as an insoluble sulfide product that can be recovered as a commercial grade concentrate. With the base metal precipitated, the cyanide can be regenerated as free cyanide and recycled to the gold extraction circuit.BioteQ completed laboratory testing for two projects, one employing cyanide leaching of copper-gold sulfide flotation concentrate and one employing a Merrill Crowe process, to determine the effectiveness of SART to remove and recover Cu and Zn in high-grade sulfide concentrates and to reduce the impact of cyanide-soluble metals on gold recovery and cyanide consumption. This paper will provide an overview of the testing methodology and results along with a review of the potential for SART to be applied to complex gold ores with poly-metallic deposits to improve project economics, operability and waste management.CITATION:Littlejohn, P, Kratochvil, D and Hall, A, 2013. Sulfidisation-acidification-recycling-thickening (SART) for complex gold ores, in Proceedings World Gold 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By E. I. Larsen, E. F. Swazy, F. R. Hensel

HIGH strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. COPPER POWDERS The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975°C. and repressing. The size of the finished compacts was ¼ by ¾ by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. [ ] In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result frequently in expansion during sintering for the type of powder used. Fig 5. indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c. c., affect only slightly the pressure required to obtain a

Jan 1, 1945

By Salvatore Fancello, Ferruccio Cribari, Amerigo Tanzi, Mauro D’Angelo, Massimo Lodico, Alessandro Bertero, Eliano Romani, Tommaso Gondolini, Fabio Giannelli

"The new metro line “C” entails the construction and rehabilitation of 24 stations and 21,5 km of metro line, 13 of which carried out underground; the new metro line will improve the transportation system of a congested city such as Rome.The new line “C” of San Giovanni metro station will be constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and will underpass the existing station. The underpass project envisages an Artificial Ground Freezing in order to excavate two new tunnels, while keeping trains running in the safest possible condition.In order to allow trains to regularly run to and from the existing station’s line “A”, a temporary structure for rail support, during excavation of the under-crossing tunnels, was installed and a real-time monitoring system was devised in order to control both soil temperature during freezing activities and the existing station’s behavior. The monitoring system has been one of the key to the success of the project.The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).THE NEW “C” LINE OF ROME’S METROThe world’s most complex and extraordinary Metro System is currently being built in the heart of Rome. Its underground route stretches underneath the most important monuments, churches and historical buildings.Rome’s Metro Line C is the longest urban underground railway in Italy and it is the first line in Rome to extend further east to the Great Ring Road, thus bridging the gap between the farthest suburbs and the Historical Centre. It is an original project, carried out mostly underground at a depth of 25/30 metres below road level."

Jan 1, 2016

By J. Petersen, S. W. Robertson

Heap leaching is used extensively for the processing of low-grade copper, gold, and uranium ores. The hydrodynamics is often the most important factor that limits the rate of metal recovery. Over the past decades the author has performed physical and hydraulic testing of a large number of ore samples considered for heap leaching. The data were reviewed to investigate the effect of physical properties such as particle size distribution (PSD) and bulk density on the hydrology. The unsaturated flow through the bed is traditionally modelled with soil science models such as Brooks-Corey (BC) and Van Genuchten-Mualem (VGM), which relate the hydraulic conductivity to the degree of saturation, also known as the hydraulic conductivity function (HCF). However, most authors found a disconnect between the saturated hydraulic conductivity (KS) and the rest of the HCF, which is explained as resulting from a transition from capillary-to gravity-controlled flow. However, the author found no such transition, and found the flow to be governed by capillary flow throughout. Traditional BC or VGM fits were found to be appropriate, however it was necessary to modify the model to include a point of inflection, above which the hydraulic conductivity remains constant while the moisture content keeps on increasing. It was proposed that this is the result of unconnected or poorly connected pores, which fill with solution but do not create additional flow channels. The point of discontinuity was also found to correspond with the air entry point, measured independently from the air conductivity curves. On average, the air entry point corresponds to the experiential rule that the void saturation should remain below 65% for aerated heaps.

Dec 11, 2024

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By E. R. Force, W. F. Cannon

Many large high-grade manganese deposits occur in marine-transgressive sedimentary sequences deposit fed on stable platforms, although the manganese mineralogy varies from carbonate to oxide facies and host lithologies vary from carbonate- to clay-dominated sections. Examples include the Nikopol and related deposits of the Soviet Union and Groote Eylandt, Australia. Recent work has shown that high sea-level stands are synchronous with stratified and stagnant oceans. We suggest that during transgressions and consequent anoxic events, the anoxic deep waters rich in dissolved manganese were dilute ore-forming fluids. Manganese was precipitated on the oxidized side of oxidation and alkalinity interfaces on shallow shelves. Where the precipitate was preserved, manganese ac- cumulated into ore deposits. Sedimentary manganese deposits have not been widely explored for in North America, nor are they always obvious in outcrop. Large areas of North America are underlain by rocks that we consider broadly favorable for such manganese deposits, and the disparity between the high potential but significant reserves of the United States is difficult to reconcile. Important undiscovered deposits seem likely. An area of Cretaceous rocks in South Dakota is presented as a possible location for a United States deposit analogous to foreign deposits described herein.

Jan 1, 1983

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By Rogério Felício dos Santos

Nitriding of metallic materials using electric discharges generated during electric discharge machining (EDM) is a recently developed technique. The aim of this paper was to correlate mechanical properties of a nitrided layer produced in AISI 4140 steel by EDM nitriding with the type and amount of nitrides. A conventional die-sinking EDM equipment and electrolytic copper electrodes were used to generate the electric discharges. The electrolyte was a solution of urea in deionized water. Knoop microhardness profiles assessed the variation of hardness along the nitrided layer, whereas the elastic modulus of this layer was measured using nanoindentation tests. Optical microscopy and X-ray diffraction (XRD) were used to characterize the nitrided surface. The results showed the formation of a nitrided layer containing iron nitrides with average thickness of around 25 µm. The amount of nitrides reduced from the surface towards the centre and these results correlated well with microhardness profiles obtained.

Jul 31, 2018

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997