Search Documents

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discusses the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that -,re being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. 3. Clay in 2 paper cartridges. 4. Commercial hydrated lime in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discussed the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that are being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. Clay in 2 paper cartridges. Commercial hydrated lira in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By Frank Alfred Fahrenwald

MetallURgical research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been , found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likeiy that a material can be produced which, will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series1 has shown that alloys of those metals maybe produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties—including the ease with which it may be soldered—are invaluable. But it is most extensively used in

Jan 1, 1916

By Bish Chanda

In the minerals business, like any other commodity-based business, management faces the daily challenge of holding down costs while the real prices of products are continually falling on an inflation-adjusted basis. Since the marketplace sets the prices, often without any premium attached for product quality, being one of the lowest-cost producers is the most viable competitive strategy. Continuous improvement is the mantra that can make the difference in terms of long-term survival of a mining company. Yet, this message has not always been followed, especially during periods of prosperity ushered by high commodity prices. More often than not, the need for improvement is only triggered by a crisis. This may be caused by events such as the onset of a severe economic recession, a prolonged oversupply situation due to an optimistic expansion of capacity during the period of prosperity, or simply falling profits alerting management to bring costs under control. At that time, there would be a need to implement a new cost-saving program, bring in a consultant to find ways to reduce costs, or re-activate an old program that had been shelved for some time.

May 1, 2003

By C. A. Rawlins

INTRODUCTION Radcont is a program designed by the author of this paper for the industry to use as an instrument for radiation contamination evaluation and ventilation planning system. Radiation in mines are associated with the mining of gold and gold bearing minerals, as uranium and thorium is incorporated in the mining of these minerals. Radiation contamination in South African mines is not a new concept as it was investigated by the Chamber of Mines in the early 1960's and found not to be hazardous at the time. Since some of our mines export scrap metal to customers abroad, it came to light (1991) that some of the scrap metal was radioactive. The authority that oversees the nuclear aspects in South Africa is the Council for Nuclear Safety (CNS). They investigated these matters and found that the mines needed further information regarding radioactive material and the handling of these contaminated materials. As the various mines were licensed (with various conditions incorporated) thereafter, the mines had to do their own investigations as to what extent their properties (Surface and underground) were radioactively contaminated. Some mines were found to be highly contaminated over the years of operation and controlling conditions were installed and measures installed to reduce the contamination levels. One of the conditions when issuing a licence by the Council for Nuclear Safety (CNS), is that a screening survey be carried out to determine the radiation exposure levels and corrective action to be taken if necessary. These surveys must be done by a person trained in the required procedures for such a survey. The person must also measure the risk correctly and assess the results properly. In such a survey, the internal and external exposure levels must be determined to assess the total exposure of persons working in those conditions and take appropriate action if necessary. When doing such a survey, hundreds and more likely, thou- sands of data points are recorded. In order to assess the data recorded, various integrated and difficult calculations need to be made, and takes up enormous amounts of time. (This excludes the interpretation of the results ) The following explanation of the program shows the different parts of such a survey assessment calculations to be done. The paper details the program layout and the different sub- sections within the primary program. It must be stated that the program, as with any other program, is as accurate as the data inserted into the data base. The program and details thereof are given under the following headings: 1. TOTAL EFFECTIVE DOSAGE WITH REGARDS TO: • GME required gravimetric results obtained (mg/m3) • Thick layer or total contamination measured (Bq/m2) • Dry condition surveys with dust loads taken as a Standard l0mg/m3 • Wet conditions survey with dust loads taken as l mg/m3 • Airborne long lived alpha and beta activities as determined by analysis in Bg/m3 • LTD (Thermoluminescent Dosimeter). Results as obtained from the SABS (South African Buro of Standards) are recorded in this section for each month of the year for each individual worker. An average dose is then determined at the end of the year. • Bucket measurements as recorded. • Smear samples (Loose contamination). As determined by Electra or by analysis • Occupational factors for Metallurgical and Engineering occupations in and around the Metallurgical facilities of your mine. • All underground dosage determination and calculations. (Radon and Thoron) 2. INFORMATION REQUIRED WHEN PROGRAM IS INITIALISED: As the program is started, it opens up on the contents page. Here there are various options to choose from, but one is cautioned as a beginner in operating the program, not to perform any tasks before carefully reading these instructions. Firstly, one must go to the 'Information required" pushbutton. Press this button. The information required page is shown where the cursor can be moved to the block where one can enter the specific mines name. To enter a mines name, put the cursor in the block provided and just insert the mines name with the normal keyboard keys and press the enter button on the computer keyboard. To enter the other information required such as Alpha and Beta instrument efficiency, ALI (Annual limit of intake) and probe area, one can either press the 'Data required" button for a dialog box information or enter it manually by just putting the cursor in the block provided and entering as did above. In order to insert all the required information for the pro- gram to calculate the information required, one must proceed further by entering the area names surveyed in the spaces provided. There are 20 spaces to enter 20 different areas surveyed. One must further also provide the amount of days worked in each area (i.8. 250) in the block provided. The de- fault is 250 days. There are also standard information given in the information data page such as breathing rate (1,2 m31h), 8 hours worked per day, 5 days per week and 50 weeks per

Jan 1, 1997

By Chao Li, Qian Li, Yong-bin Yang, Kai Li, Qiang Xie, Yuan-yuan Zhu, Dong-ye Li, Qi-bing Tan

"The permeability of sintering mix is a vital technological property in sintering process. However, it can only be measured by off-line method on samples picked from the production. In order to acquire the properties of sintering mix accurately, on-line measuring of permeability is urgently required. Based on the reflection characteristics of bed permeability on pipe flowing parameters, a new method is presented in this paper for on-line measuring of sintering mix permeability. The measurement can be performed by blowing gas flow in the bed with the measuring pipe. Measuring results are obtained by picking the data on flowing rate and pressure in the pipe. The function of flowing rate to pressure may be certain for samples with the same permeability. Thus, the permeability was determined by contrasting this function to the result of off-line measuring, and the relative coefficient or R2 value was more than 99%.IntroductionThe permeability of sintering mix is a vital technological property in sintering process, which directly determines production and quality of sinter, or even determines whether the sinter production is carried out smoothly [1,3].The permeability have more obvious influence on vertical sintering speed, which is mainly related to air quantity passing through material bed. Under certain inducing capacity and negative pressure, the vertical sintering speed mainly depends on the permeability of sintering mix. Low permeability may make burning through point of sintering move back, and the sinter mix cannot be burnt through. High permeability may make burning through point of sintering move forward, improving production efficiency by increasing the speed of sintering machine [4] Good permeability means a small resistance of fan ,reduction of negative pressure of sintering machine, and full contact between air and sulfide, which can strengthen physical-chemical reaction during sintering process and increase desulphurization rate. In gas well through material layer process, gas-solid desulfurization reaction and gas-solid-liquid heat exchange are completed and hot gas through the combustion zone supplies the sintering process with heat. Finally uniform sintering of the material layer in height and width direction is achieved [5] While high permeability index leads to weak sinter strength, fast sintering speed, short residence time of high temperature region and little liquid phase. Moreover, liquid phase in the fast cooling process is too late to fully crystallize but forming glass phase which is harmful to sinter strength as well. Bad permeability means a big fan resistance and increase of negative pressure of sintering machine, which make the air pass through material layer difficultly. When air and mix contact difficultly, removal of sulfide reduces so that desulfurization is incomplete. Meanwhile, low caking efficiency, slow sintering speed and easily burnt sinter , reduce sinter output. Therefore appropriate permeability of sintering mix is the premise of stable burning through point and satisfactory sinter output and quality."

Jan 1, 2013

By Alexander Gow

THE object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the "bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a compre-hensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific varia-bles, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this "new philosophy" consists of using power as an index of the mill operation, and investigating grind-ing from the standpoint of set and induced variables, with emphasis on the latter.

Jan 1, 1934

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By Sergey Komarov, Manuela Diaz, Sano. Masamichi

"Mixing time, bubble behavior and absorption rate of gas injected into a liquid bath through rotary L-shaped lances have been studied by cold models with an effort to improve refining characteristics of metallurgical processes. Two kinds of the rotary lances were tested, namely the single-hole lance and the multi-hole lance. The effects of gas flow rate, bath depth and rotation speed were examined.It is found that when gas is injected through the rotary lances, the mixing intensity and the gas absorption rate are larger than that for the gas injection through stationary lances. The effect of rotation speed decreases as the bath depth and the gas flow rate increase.The multi-hole lance produces much smaller bubbles, which lead to an increase in the volumetric mass transfer coefficient by 3-4 times as compared with the single-hole lance. However, the effect of rotation speed is smaller for the multi-hole lance. The obtained results are explained in terms of the bubble coalescence and fragmentation, the rate of which depends on the departure bubble size and the power supplied to the liquid bath.IntroductionIn recent years, there has been a growing interest in the development of gas injector for metallurgical processes. The majority of the previous work was focused on modification to the injector design to improve mixing and to increase the of chemical reaction rate. These two goals can not be necessarily achieved by the same way. Bottom nozzles and stationary immersed top lances, which have been widely applied to steelmaking processes, are effective for the bath mixing, but have a limit to decrease in the bubble size. This results from a vigorous coalescence occurring between the bubbles when they rise in the molten bath as a bubble swarm.One of the ways to ensure the small bubble size and the effective bath stirring is the gas purging through rotary injectors. A number of studies have been undertaken to improve the refining characteristics by using rotary injectors. All of them are related to aluminum refining. The SNIF equipment (The Spinning Nozzle Inert Flotation) has significantly improved the quality of aluminum products at National Luxemburg Aluminum [1]. Rotary injectors made in the form of a disc have been applied to the Alcoa 622 [2] and the GBF processes [3]. A study of the gas injection by a rotary impeller has been carried out by C. Leroy and G. Pignacelt [4]. All researchers note the significant improvement in removal of sodium, calcium, hydrogen and non-metallic inclusion."

Jan 1, 1996

By V. C. Wansbrough

First, permit me to say with what very great pleasure we find ourselves assembled in this most ancient and honourable city of Quebec. It is a city which we deeply respect as the fountain-head of the culture of French-speaking fellow citizens, and the seat of government of a province which is steadily recording new achievements in Canadian mining. Such achievements prove what can be accomplished when enlightened and progressive government policy, technical and scientific competence, and private initiative pull forward together in harmonious rhythm. It is a most happy and auspicious event also that the guiding control of the affairs of the Institute and of the fine traditions of provincial administration have for the past year been united in the person of our honoured President, Dr. A. O. Dufresne. This year, again, we have bad prepared for us by our hosts a splendid programme of technical sessions and social entertainment. Each year we pay an unspoken compliment to the Institute, expecting as a matter of course nothing but the highest standards in both these spheres. In its annua1, semi-annual, and regional meetings, in the constant activity of its local Branches, the Institute continues with marked success to perform its great dual service, social and educational. We are all its beneficiaries to the extent to which we choose to profit by participation in its affairs. But, one imagines, to none are the advantages of Institute membership more valuable than to young men embarking on their professional careers.

Jan 1, 1951

By B Kretschmer, G Bartel, B de Villiers, W Watt

"The Nyrstar Port Pirie Smelter, located on the eastern shore of the Upper Spencer Gulf in South Australia 230km north of Adelaide, began operation in 1889 to process lead concentrate from the Broken Hill lead and silver mines. The site still operates an updraft sinter machine, commissioned in 1955, with the product fed into a blast furnace. While sinter plant technology has changed and improved since 1955, development has reached the stage where further enhancements are not possible or economic. High purity lead concentrates command lower margins and for the smelter to remain economically viable a wider range of higher value materials must be treated. The current flowsheet cannot meet this demand. Additionally, community blood lead levels particularly in children below four years of age, are a critical indicator used to measure the site’s environmental performance. The smelter’s environmental licence to operate is dependent on meeting future community and regulatory expectations. To achieve this a major step change in the emission performance of the smelter is required. Since 2008 pre-feasibility work has been undertaken to develop a new flowsheet and business model to allow Port Pirie to operate sustainably into the future. The main requirements were for the smelter to reduce lead and sulfur dioxide emissions that impact on the local environment and community to meet current and future environmental expectations, as well as dramatically reducing current feed constraints and change the business case from a marginal business to a sustainable profitable business. After reviewing all practical options a decision was made to replace the sinter plant with an Outotec Top Submerged Lance (TSL) furnace. This paper describes how the new furnace technology was selected and how it will be integrated into the present flowsheet; the unique funding arrangements that are in place to deliver the redeveloped site; and future opportunities that are associated with the implementation of the new flowsheet. CITATION: De Villiers, B, Bartel, G, Watt, W and Kretschmer, B, 2015. Nyrstar Port Pirie redevelopment, in Proceedings MetPlant 2015, pp 325–337 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 7, 2015

By D. Mills, W. J. Brantina

"Mechanical and magnetic characteristics of ferromagnetic materials were investigated by a pulsed ultra-sonic technique. Two instruments, the Ultrasonic Attenuation Comparator (Sperry) and the standard type Reflectoscope (Sperry) were used for measurements of the attenuation of the ultrasonic pulse. The effects of elastic tensile and compressive stresses on the attenuation of annealed and cold worked material are described. In addition, the effects of plastic de-formation, relaxation and aging processes and different ultrasonic test frequencies are reported. The results for Armco iron, SAE 1020 steel, SAE 4340 steel and AISI 420 stainless steel are shown. Under the test conditions, the attenuation was found to be largely a sum of two components; a ""dislocation"" component associated with the losses accompanying the oscillations of dislocation line segments and a ""ferromagnetic"" component associated with the microeddy currents generated by magnetic domain wall oscillations. Either of these components might be dominant depending on the nature of the particular specimen and the test conditions. Finally, the possibilities of using ultrasonics in residual stress determinations, in fatigue studies and in the study of the ductile-brittle transition in ferrous materials, are briefly discussed."

Jan 1, 1960

By J. P. Messervey

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947

By Musa Karakus

The sedimentary iron ores of Alsace-Lorraine, France have very high phosphorous contents that average 0.7% and are as much as 2.19% P. Ores from the Tucquegnieux and Joeuf mines have been studied by cathodoluminescence microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe analysis in order to fully characterize the mineralogy, size, shape, and distribution of the deleterious phosphate grains. The phosphorous occurs as collophane, a carbonate fluorapatite, in ten morphological forms, most abundantly as microcoprolites, but also as intraclasts, concentric layers, and cortices in ooids, phosphate replaced ooids and bioclasts, phosphatiC shells, fossil infillings and internal molds, fish teeth, phosphatiC laminae, and cements between the goethite ooids. About 95% of the phosphate grains are sufficiently large that relatively fine grinding fol'lowed by reverse flotation would be expected to be effective in significantly diminishing the phosphorous content of the concentrates.

Jan 1, 1989

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By Teresa Sikora

For over 40 years the Institute of Innovative Technology EMAG has specialized in the development of systems and equipment for laboratory and on-line monitoring of coal quality parameters, as well as the implementation of these systems and devices in mines and power stations. Some of these systems, based on advanced radiation detection techniques such as ?-ray backscattering (ALFA-06 and ALFA -06/T systems) or dual energy ?-ray transmission measurement (ALFA-06/2E ash meter), and also the ALFA-06/3E system applying microwave technology for the measurement of moisture, have had numerous applications in Poland. At present, over 100 systems and devices are used in Polish hard and brown coal mines. For over 10 years, EMAG has been specializing in the development of systems and devices, based on natural gamma measurement technology. An on-line ash meter, RODOS and RODOS Ex, based on measurement of natural gamma radioactivity of coal, has been developed and put into operation. This technique has been also used in developing the portable ash meter WALKER and laboratory analyzer GAMMA NATURA. The paper briefly presents features of the above-mentioned devices, their limits and their obtained accuracy, but in particular refers to the laboratory analyzer, GAMMA NATURA, as the first such device in the world, and presents the results of ash and moisture content measurement in hard, brown coals and potassium salts. The possible applications and advantages of the device in coal mines are discussed. The paper also presents the implementation results of the portable ash meter, WALKER, and the on-line ash meter, RODOS, that is used underground in coal mines.

Aug 1, 2013