Search Documents

By H. Kohno

The Onahama No.3 tankhouse started commercial operation in early 1973, with the capacity of 8,500 metric tons per month. When the No.3 tankhouse was constructed, the starter sheet stripping section was rebuilt at the No.2 tankhouse and electrolyte purification section was expanded. The previous AIME paper in 1976 described the design principles of the No.3 tankhouse and its layout, This paper describes the starter sheet stripping machine in the No.2 tankhouse and the electrodes handling system in the No.3 tankhouse and all these equipments were developed for the operation of the No.3 tankhouse. A Hazelette continuous casting machine was also introduced in order to cast thin anodes with accurate shape. Owing to the adoption of thin anodes, gold, silver and copper inventory is reduced by 40%. Jumbo tanks and newly developed mechanical equipments were adopted and no work on cells during pulling up operation was achieved. Using thin anodes with accurate shape, inspection work was completely abolished while maintaining high current efficiency and high cathode quality. Labor cost was reduced by 70% and only six operaters can produce? 8,500 metric tons of cathodes per month. The same new electrolysis process is appreciated and has been used as a newly built independent tankhouse by Kidd Creek Mines Ltd., in Canada in 1981 with excellent results

Jan 1, 1987

By J. F. Barkley

The work covered in this report was done to meet the requests from many Government agencies for information on alleviating sludge difficulties in No. 6 (Bunker C) fuel-oil storage tanks. Accumulated sludge at times caused serious loss in tank capacities; pumps became overloaded or lost suction; strainers often required very frequent cleaning; fuel-oil heaters in some instances became fouled and inefficient; and gobs of sludge that passed the strainers interfered with good combustion. The requests also included questions regarding the usefulness in general of oil "additives" for preventing sludge and the relative merits of the many trade-named additives being marketed. Realizing that preventing such difficulties would result in substantial savings to the Government, an investigation was begun with the limited funds avail-able. Although various claims are made for No. 6 fuel-oil additives other than preventing sludge, only an investigation as regards the storage tank-sludge problem has been possible.

Jan 1, 1955

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By J-P Franzidis

Mill operators have traditionally been forced to rely on grade-recovery curves and overall flotation rate constants when analysing proposed improvements to plants. This has led to loss in money and time when a proposed change that showed potential in laboratory scale tests failed to show improvement in the plant. Frequently, this is a result of the operators being unable to gain insight into how and why the proposed change affected the flotation performance. This is due to the classical models not including any description of the subprocesses of flotation and their individual contribution to the overall flotation performance. A new flotation model has been developed as part of the AMIRA P9 project that separates the flotation process into subprocesses and includes the contribution of both the pulp phase and froth phase to the overall flotation recovery. It is not possible to determine the individual components of this new model on traditional pilot plants as they lack the required flexibility and scale. Therefore a new pilot plant has been developed known as the Floatability Characterisation Test Rig (FCTR) that has the flexibility and features required for the determination of the flotation subprocesses. The flexibility and features of the FCTR also make it an ideal tool for investigations into many different aspects of flotation research. These include the effect of reagents, grinding, and power on the flotation performance. This paper will describe the methodology for using the FCTR in these fields of research and highlights the advantages of using the FCTR over traditional methods.

Jan 1, 2000

By G. W. Sheary

At Bethlehem's Grace mine's 6000-tpd pelletizing plant a cascade control system is utilized to approach a constant magnetite filter cake moisture, a critical factor in obtaining quality green pellets. Variables being controlled by instrumentation are filter feed solids, filter tub level, first and second stage pump sump levels and thickener sludge level, all at varying feed rates. Startup difficulties, modifications and contemplated additions to obtain closer control of the moisture are discussed. Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Co. 's Beth-lehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with %-in. slotted vibrating screens. The ore is washed and screened in the mill and the 1/4-in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30-in. cyclones, to 1% on 100 mesh and 65% -325 mesh. The ground ore is magnetically concentrated by three-drum permanent-type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50-ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% +'1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica. It has been the usual practice to maintain constant filter tank level by pumping an excess constant volume and using a moveable fishtail splitter to divert the desired amount of slurry to the filter tank. The excess from the fishtail and from the filter overflow pipe, which maintains a constant level, is returned to the source. At the Grace mill, tremolite builds up in the pipelines when pumping heavy magnetite concentrate slurries, making it necessary to use polyvinyl

Jan 1, 1962

By Oliver B. Hopkins

"WE HAVE patterned our lives on the things we take from under the earth's surface. Our civilization is built upon the ore from which we obtain our metals and the fuels which power the world as we know it.Today I should like to discuss with you a newcomer to the ancient mining industry. This lusty infant of which I speak is just a century old - the oil industry.While one doesn't commonly think of oil men as delvers in the earth, It was by sinking a shaft that the first oil was obtained commercially in Canada. Men sank a shaft in a ‘gum bed' in southwestern Ontario's Lambton county, not far from Petroilia, and distilled from the gum a burning oil That was just a hundred years ago. The gum was originally liquid petroleum which had seeped to the surface and lost most of its volatile components.Later, the miners dug down to •bed-rock and soon after they were not digging but were drilling wells, as they have been ever since. From the wells they obtained erode oil.What is crude oil? It is not an element like gold, silver or lead, •but a complex mixture of compounds. These compounds are made basically from two elements, carbon and hydrogen, and are called hydrocarbons (Figure 1).The remarkable ability of these. Two elements to combine in different ways gives crude oil its physical and chemical character. The lighter hydrocarbon compounds in it are gases, at normal temperature and pressure, and these are dissolved in the other, heavier compounds."

Jan 1, 1952

By J. C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1995

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By John G. Kelly

"In 1982 an extensive study was carried out to determine the best means of size reduction for the ore to be hoisted through the borehole hoisting system at Sherritt Gordon's Fox Mine.The study examined three alternatives:1. a jaw crusher,2. pneumatic rockbreaker(s) at a grizzly, and3. hydraulic rockbreaker(s) at a grizzly.The final decision was a compromise between alternatives 2 and 3. Two rockbreakers, one pneumatic and one hydraulic, were installed over a single grizzly. Some modifications have been made to the system, but over-all it has operated at acceptable levels since its installation in July 1983.As all the ore passes through a jaw crusher before being hoisted to surface, an evaluation of the relative performance and cost-effectiveness of the jaw crusher and the two types of rockbreakers is possible. This paper outlines the initial study, and compares the three breaking systems in operation at Fox Mine.IntroductionThe Fox Mine of Sherritt Gordon Mines Ltd. is located 800 kilometres north of Winnipeg near Lynn Lake in Northern Manitoba. Production at the copper-zinc orebody began in 1970 at a rate of 3,000 tons per day. Over 12.5 million tons will have been hoisted from the underground mine when the ore reserves are depleted in October 1985.The mining method at Fox Mine is sub-level open stoping with delayed backfilling are from the upper level stopes, above the 2000 level, is mucked on the main levels established at 400-ft elevation intervals, and is fed through a central orepass to the crusher located on 2100 level. Production in the lower levels commenced in 1975, and ore from the 2200 and 2400 level stopes was hauled up a 15010 ramp by 26-ton trucks to the 2000 level orepass dump. Projected production rates from the 2600 and 2800 levels using the trucking system were too low, and therefore, in 1983 a borehole hoisting system was commissioned to hoist that ore'!'. One thousand tons per day of ore are skipped through an 8-ft diameter borehole from the 2650 level loading pocket and dumped on the 2000 level. The ore is transferred by LHD to the main orepass for crushing before being conveyed to the main shaft for hoisting to surface (Fig. 1)."

Jan 1, 1986

By PáDeáBosscher, A Bruwier, M Weidenbach, C Philippe, T Ly, A Van Den Bosch

In the mining business the cost of grinding media represents up to 40 per cent of the total milling cost and therefore grinding media optimisation has a direct impact on the concentratorsÆ bottom line. In the process of optimising grinding media alloys, Magotteaux developed its own methodology which consists of a series of analyses, tests, calculations and evaluations and assist the concentrator in optimising their processes.This paper presents the Prominent Hill case study where this methodology has been applied on both the secondary ball mill and regrind IsaMill«.The analysis of the wear conditions in the secondary ball mill allows Magotteaux to select a series of grinding media alloys to be tested to reduce grinding media consumption. By marking these different grinding media types with a unique drilling pattern, one can quantify the relative wear performance and cost effectiveness of each grinding media type within the same milling environment. After selecting the most economical grinding media composition a full scale industrial trial, involving topping up the selected grinding media is carried out and the media wear performance closely monitored and analysed.For stirred grinding mills, suppliers propose different grinding media, mainly ceramic beads, with specific properties and cost. Therefore the concentratorsÆ choice is a compromise between grinding efficiency, wear resistance and cost. The selection of the correct grinding media for stirred milling and the assessment procedure will be presented in this paper. The test results of the new stirred grinding media type in the regrind IsaMill« at Prominent Hill are presented and analysed.CITATION:Weidenbach, M, Van Den Bosch, A, Bruwier, A, Ly, T, De Bosscher, P and Philippe, C, 2012. Forging ahead - A collaboration between the OZ Minerals Prominent Hill Concentrator and Magotteaux to improve plant performance, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 105-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

By Morgan M. Sears, lhsan B. Tulu, Ted M. Klemetti

"Why do some room and pillar retreat panels encounter abnormal conditions? What factors deserve the most consideration during the planning and execution phases of mining and what can be done to mitigate those abnormal conditions when they are encountered? To help answer these questions, and to determine some of the relevant factors influencing the conditions of room and pillar (R&P) retreat mining entries, four consecutive R&P retreat panels were evaluated. This evaluation was intended to reinforce the influence of topographic changes, depth of cover, multiple-seam interactions, geological conditions, and mining geometry.This paper details observations made in four consecutive R&P retreat panels and the data collected from an instrumentation site during retreat mining. The primary focus was on the differences observed among the four panels and within the panels themselves. The instrumentation study was initially planned to evaluate the interactions between primary and secondary support, but produced rather interesting results relating to the loading encountered under the current mining conditions. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the stress conditions. Both the LaModel 3.0 and Rocscience Phase2 programs were used to evaluate these four panels. The results of both models indicated a drastic reduction in the vertical stresses experienced in these panels due to the full extraction mining in overlying seams when compared to the full overburden load. Both models showed a higher level of stress associated with the outside entries of the panels. These results agree quite well with the observations and instrumentation studies performed at the mine.These efforts provided two overarching conclusions concerning R&P retreat mine planning and execution. The first was that there are four areas that should not be overlooked during R&P retreat mining: topographic relief, multiple-seam stress relief, stress concentrations near the gob edge, and geologic changes in the immediate roof. The second is that in order to successfully retreat an R&P panel, a three-phased approach to the design and analysis of the panel should be conducted: the planning phase, evaluation phase, and monitoring phase."

Jan 1, 2016

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014

By G. Duncan

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above..

Jan 1, 1999

"Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.INTRODUCTIONThe National Institute for Occupational Safety and Health’s (NIOSH) Office of Mine Safety and Health Research (OMSHR), formerly the United States Bureau of Mines, has been conducting research on ground control safety for over 50 years. The overall objective of the research is to reduce underground mining injuries and fatalities by characterizing roof conditions, improving roof support performance and application, and optimizing pillar design and mine layout. Underground mining has one of the highest fatal injury rates of any industry in the United States—more than five times the national average compared to other industries (CDC, 2012). Roof fall injuries can be severe, resulting in lacerations, bone fractures, amputations, and death. Non-injury roof falls can also be problematic, resulting in lost production, delays, blockage of primary escape routes, disruption to ventilation, and hazardous rehabilitation conditions.Coal mining is increasingly subject to more adverse geological conditions. Weak roof can be found in all coal mining regions in the United States, but there are a few geographically isolated areas with higher roof fall rates contributed to by particularly poor roof conditions, as represented in Figure 1. This figure shows that when non-injury roof fall rates are normalized to production, the Illinois Basin and Central/Northern Appalachia regions have the highest rates. These isolated regions have inherently weak roof even before mining has occurred, and this roof is easily damaged during the mining process. The weak roof in these regions consists primarily of shale. Shale can be troublesome in underground coal mining because it can appear massive but easily splits along bedding planes and is often moisture-sensitive."

Jan 1, 2015

By M Costa, L Polizzi

Process optimisation and continuous improvement are usually acknowledged when making a process more effective, efficient and transparent. During the last few decades, thousands of companies around the world have used total quality concepts in order to establish a continuous improvement process in their companies. Typically these companies apply some kind of Kaizen-type tools and expect results in the short term; however, the great majority of companies are poorly implementing these continuous improvement programs.Usually the most common reasons for failure of the program are lack of commitment from leaders, lack of discipline and engagement from the team to follow process and lack of clear targets for the program. When the results do not come at the expected timeline, it is common to simply drop the current process and apply a different approach from another company or consulting firm.This paper will explore some successful cases of companies that have invested time and effort to establish a reliable and sustainable process of continuous improvement. The focus will be case studies of mines and smelters around the world that use the plan–do–check–act (PDCA) cycle to increase productivity with the best services and lowest costs. The main tools and processes used by these companies will be discussed, as well as results achieved.CITATION:Costa, M and Polizzi, L, 2014. Introducing and sustaining a continuous improvement program in mines and smelters, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By K. Shame, H. H. Thiele

South Africa holds approximately 70% of the world’s total chrome reserves. Chromium is an important raw material for the production of stainless steel and ferrochrome alloys. Over the years, China’s ferrochrome market has been dependent on chrome ore imports from South Africa. In 2018, China imported about 75% of its chrome ore from South Africa. With the low platinum price and the rising demand for stainless steel, a growing demand to evaluate new beneficiation technologies for fine chromite was identified. Gravity separation of fine chromite (<75 μm) is inefficient, due to the limitations of the technology to upgrade fine particle size distributions. Potential for the recovery of chromite, specifically fines (<75μm), lost to UG2 PGM flotation tails, but also from MG and LG6 spiral circuit tailings exist. Flotation of podiform chromite ores from India and Kazhkhstan is successful in generating saleable product grade, following acid or alkaline flotation routes. Application to South African stratiform chromite is being evaluated, with the emphasis on evaluating reagent type, optimising dosages and the effect of pH in optimising flotation performance. Flotation can unlock additional value from chromite tailings material. The effect of ore characteristics such as gangue mineralogy, particle size distribution and headgrade are reported. The performance in terms of product quality and yield are evaluated and compared. The impact of this paper will not only prolong life of mine and increase revenue but will also alleviate environmental burdens associated with tailings dams. Keywords: Chromite, flotation, fine material, performance optimisation

Jan 1, 2020

By Tom Lewis

This report discusses the evaluation of the ENVIRO-CLEAN PROCESS, a technology developed by Lewis Environmental Services, Inc. for the recovery of metals such as chromium, mercury, copper, cadmium, lead, and zinc from surface and groundwater streams. This new heavy metal removal process (patent-pending) utilizes granular activated carbon with a proprietary conditioning pretreatment to enhance heavy metal adsorption combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA limits. A 50 gpm system was installed for recovering hexavalent chromium from a ground water stream at a site located in Fresno, California. The effluent from the activated carbon system was reinjected into the ground water table with the hexavalent chromium concentration < 10 ppb. The system simultaniously removed trichloroethylene (TCE) to concentrations levels < 0.5 ppb. The activated carbon is regenerated off-site and the chromium electrolytically recovered. The full scale system has treated over 5 million gallons of ground water since installation.

Jan 1, 1996

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006