Search Documents

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968

By E. W. Enqelmann

INCREASED metal consumption throughout the world in the past three years has brought greater activity in the concentrators and mills that treat the ores.' Comparatively low prices have made greater economies necessary, with a continuing search for more efficient flow sheets, equipment, processes, and reagents. Comminution GRINDING has long been too ex- pensive and even any small increment of saving has been eagerly sought. Although not recently new the use of rod mills to cover the gap between intermediate crushing and coarse grinding has made further headway. They eliminate dusting and the closed- circuit operation of fine crushers, either roll or Symons cone, and the rod-mill product is suitable for secondary mills which can be operated with smaller balls and iron liners instead of coarse balls and steel liners. The newer practice is radically different from the older application of rod mills where they at- tempted to use them instead of ball mills for fine grinders. For that purpose they were not well adapted, as they do not have sufficient grinding surface available per cubic foot of mill volume.

Jan 1, 1940

By A Turner, P Hills, D Johnson

Underground mining for gold began in Beaconsfield in 1877 and development of the Tasmania Mine saw the sinking of multiple shafts, including the Hart Shaft over the ensuing 35 years. The mine closed in 1914 at a depth of 455 m due to prevailing economics, eventually reopening in 1999. The modern mine closed in 2012 after extending the mine from a historical depth of 455 m to the exhaustion of the modern Ore Reserve at a depth of 1210 m. West Tamar Council took over the lease for the immediate area around the Hart Shaft as an extension of the adjacent museum. The Hart Shaft and above ground structures became a significant drawcard for visitors. Tasmania was affected by sustained wet weather during May, June and July of 2016 which caused severe flooding and significant Statewide damage. This uncharacteristically intense wet weather caused saturation of the ground surrounding the Hart Shaft. Eventual shaft failure was first identified in August 2016. The failure of the shaft occurred at approximately 50 m below surface and resulted in a plug of material completely blocking the shaft. Significant surface subsidence affecting the surface infrastructure ensued. Due to the unstable nature of the surrounding material, it was determined that addressing the failure above the blockage would not provide a permanent solution to prevent the continued flow of material into the shaft. Many options to stabilise the shaft were considered, however it was assessed that a concrete plug in the shaft in competent ground at a depth of 100 m below surface and well below the blockage, would provide the only long-term solution. Man-entry was considered unsafe. The solution to access ultimately entailed filling the entire shaft with granular fill up to 100 m depth to act as formwork for a concrete plug. The rising mains at 400 mm and 250 mm diameter, which remained in place in the shaft, provided the avenue for placing the fill and ultimately, the concrete plug. Once the plug was in place the remainder of the shaft up to the underside of the blockage and over the top of the blockage to the surface was successfully filled with a combination of more granular fill and flowable cement stabilised sand. The Hart Shaft and surrounding above ground infrastructure was successfully stabilised and re-opened to tourist access. CITATION:Johnson, D, Turner, A and Hills, P, 2018. Stabilising and filling the Beaconsfield Hart Shaft, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 42–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J. M. West

Increased leisure time and increased interest in the out-of-doors is leading more and more families to experiment with placer mining of gold, and some- times even to going on into small-scale production. This Bureau of Mines report supplies basic information un areas of occurrence, equipment needed, prospecting, sampling, mining, and regulations concerning the possession and sale of gold. Selected references are given for further study.

Jan 1, 1971

By W. G. Pariseau

A two-dimensional finite element program has been modified and extended to account for some of the rock mechanics complexities associated with single entry development of longwall coal mine panels. Program capability includes arbitrary assignment of element properties without regard to element ordering, anisotropic elastic, plastic and brittle rock properties that may be time dependent (aging), arbitrary mining sequences and provision for the effects of artificial support on the adjacent strata. Failure is according to an extended von Mises criterion that may be linear or quadratic in form; flow rules are obtained from the yield function taken as the plastic potential, but brittle behavior is treated as a discontinuous process of material properties change with deformation. In either case the extent of failure is calculated from the external boundary conditions. Application of the program to essentially two-dimensional problems resulted in lose agreement between calculated displacements and field measurements in the double entry system. Bleeder entries were stable in one locality and not in another. Artificial support had little influence on stability.

Jan 1, 1978

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

By W. E. Foreman

A mathematical model was developed to assess the costs for reclamation of surface mining using the shovel overcasting operation, the front end loader operation, and a backfilling operation. A literature review was made of the present laws in Kentucky, Pennsylvania, Virginia, and West Virginia pertaining to surface mining and of the various parameters that influence the input data for a mathematical model. It was determined that the working mathematical model would have to be applied on an area to area basis, preferably on a permit by permit basis in the area where surface mining was being done. To this end, a flexible model was developed with input data obtained from the area of study. The results of the study show that the cost per ton of coal for reclamation can be estimated for various reclamation levels. Validation of the model was done for selected permits from Virginia. It was determined that the permits could easily be used for input data to the model.

Jan 1, 1974

By J. H. Gasper

A cost analysis for two alternative contour mining methods is performed to compare their results. The methods evaluated are: 1) Front-End Loader/Truck Haulback and 2) Scraper Haulback. Before performing these analyses, output requirements and equipment needs are found based on integrating geometric limitations with material properties. The final geometric design establishes limits on clearances, congestion problems and grades (with associated running surface materials). All calculations are kept practical, with assumptions clearly stated. The cost analysis is a unique, easily utilized compilation of several different approaches incorporating cost engineering principles. The strengths of each are welded into a cohesive entity once again aimed at practical application. The results are presented in tabular form.

Jan 1, 1992

By Paul Sterling

1. INTRODUCTION. THE general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a "coal-breaker." This name is misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only in the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for domestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Oct 1, 1911

By Y. Ye

Typically, rougher molybdenite flotation and recovery from bulk copper/ molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment for the depression of copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40 and 90% at a concentrate grade of 5 to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Me concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning results in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/flotation strategy, the process is technically and economically viable and should be suitable for industrial application.

Jan 1, 1990

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

WHEN pouring concrete it frequently happens that space prohibits the placing of a mixer at the point, or points, where the concrete is to be used. Usually in such cases recourse is had to some form of pressure chamber, or concrete gun, to blow the mix by compressed air from the mixer to the point of pouring. Recently such a case arose at one of the western mines. The experience obtained there may be of benefit to others, not expert in the means of transporting mixed concrete, when they run up against similar situations. The first stage in pouring in this instance was a vertical drop of 100 ft. from the mixer on one level to the point where horizontal travel began on a lower level. Standard 6-in. pipe with flange joints was used, hung in the shaft space available. A standard 45" bend near the bottom directed the mix, with free discharge, into an air chamber for the horizontal stage of travel. With an air chamber at the mixer and pressure applied to the falling mix in the vertical section, jamming frequently occurred at the turn and the pipe would have to be taken apart for freeing. To obviate this difficulty the mix was poured slowly without the addition of air pressure, when it was found that the mix got through much better.

Jan 1, 1929

By M. S. Millman

Close monitoring of performance at each process stage, from raw material through to finished product, is vital for operational consistency and the production of high quality steel. However, many of the integrated iron and steelmaking process route stages operate under such severe conditions of temperature, dust, water, thermal radiation, vibration, pressure, vacuum, extreme dynamic events, high material flows, corrosion, erosion, electrical-noise, electromagnetic-noise, or audio-noise that, in general, it is a very difficult challenge to obtain useful information for control. Thus, state-of-the-art non-contact and remote sensors are applied to help monitor and control specific process operations. Often, these sensor systems have been developed especially for the steel industry and they are based on four principal technologies: Laser, Microwave, Electro-Magnetics and Thermal Imaging with supporting technologies such as: X-ray Fluorescence, Audiometry, Digital Image Processing, Radio Telemetry, GPS and many others. These advanced sensor technologies are reviewed with respect to their application at various stages along the integrated process route.

Jan 1, 2004

By Randall Wheeler

In early 2008 we were asked by a quarry to become involved in a conflict with a pipeline company concerning blasting near one of their underground high pressure gas lines. The pipeline company, without the quarry’s knowledge, had sought and obtained a temporary restraining order against the quarry forbidding them from blasting near the pipeline.

Jan 1, 2011

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

The absence of coal face particle management practices heavily penalizes coal transportation from initial loading to final consumption. Penalties include dust problems, significantly reduced mine loading cycle productivity, mine belt spillage, excessively high coal preparation costs and chute and dangerous pulverizer blockages at the final point of utilization. The common environmental and economic enemy is fines. Everyone knows that fines cause safety and environmental dust problems, but few understand that fines also swell broken coal to a point where 5 to 15 percent more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long established and frequently misleading basis of tonnage. After all, it is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain non-frothing chemicals added to mine face spray water and/or by employing improved mine face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed.

Jan 1, 1994

By Sebastián Seria, Jorge Álvarez, Diego Cáceres

The capacity to break the rock into adequate size fragments and in a cost-effective way is one of the main challenges in large open pit copper mines in Chile. That capacity is often compromised by the accuracy of geological estimations and the resources allocated by the mine site to update those models, making the blasting design highly dependent on that input and in consequence, blasting results. Given these opportunities, having an alternative method to input estimated key geological parameters allows blast designers to modify their designs and apply the appropriate energy to achieve the desired results. By using measurement-while-drilling data from boreholes and a few samples of actual, widespread, hardness measurements on site, we can deliver an updated cost-effective hardness estimation that is used as an input to improve the blasting design and its results on fragmentation. This estimation is delivered as a hardness interval – often in MPa units- related to the position of actual drilling measurements. In addition, having a sufficiently large drilling dataset allows us to predict hardness in new, undrilled areas near already measured boreholes, serving as a prior estimation available before pattern design. The use of these estimations, applied to several copper mines in Chile, allow us to more accurately determine explosive amounts and borehole drilling, which directly contributes to more productivity and efficiency in mine site operations. The results are often related to narrowing the gap for fragmentation results, even so, in some cases that will be related to direct savings in Drilling & Blasting process in a range 5-10% of the budget, due to powder factor changes.

Jan 26, 2026

By P. F. MINISTER

AT Lime Spur, Mont., the East Butte Copper Mining Co. has been quarrying limestone for twenty years. The quarry is beside the Northern Pacific R. R. in the Jefferson River canyon, 4 ½ miles east of Cardwell, at Lime Spur, Montana. HISTORY This quarry was opened early in 1900 by Dan Morrison of Whitehall, the discoverer of the Morrison cave, to supply a demand for smelter flux. Limestone was sold to the Pittsmont smelter of The East Butte Copper Mining Co. and to the Butte Reduction Works. As no particular effort was made at the quarry to select the rock that delivered to the smelters was unduly high in magnesia and impurities. The East Butte com¬pany, therefore. Bought the quarry. in 1909 and confined operations to the high-grade beds in order to supply rock of the desired purity for its own smelter and the Butte Reduction Works until the latter shut down. It also developed a market for some of its rock with the sugar factories. The latter market increased until in later years all rock, larger than 4 in. in size over a bar grizzly, was being shipped to the sugar factories, and the rock smaller than 4 in. was being used as a flux in the blast furnaces at the Pittsmont smelter. In 1924, the East Butte concluded a contract with the Anaconda company for the treatment of its ores, and the Pittsmont -smelter -was shut down: which made the minus 4-in. rock a useless by-product. Since there was not enough revenue in the sugar rock alone and also because of limited waste room it became necessary, if Lime Spur was to continue to operate, to increase- the proportion of plus 4-in. rock and to develop a market for the minus 4-in.

Jan 1, 1930