Search Documents

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930

By A. N. Pritchard

The development of vibrating screens over the last century has seen many variations to suit the exacting requirements of industry. Indeed, as each year passes, industry has presented the challenge to screen manufacturers of supplying larger machines than those used in the past and the question is often posed - what is the maximum limit? Not only must size or screen area be considered but excellence of performance in terms of screening efficiency must be maintained or maximized.

Jan 1, 1983

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By H. Mulder, M. C. Bekker

The principal objective of this investigation was to conduct a thorough literature review on the status of project readiness mechanisms, tools, techniques, and frameworks for mining projects. The review aimed at identifying common readiness evaluation criteria as well as potential shortcomings that prevent the establishment of a generalizable project readiness index. The literature review included a general overview of capital project performances and the importance of project readiness assessments to improve project delivery success. The study then progressed towards literature involving mining projects and how this differs from infrastructure and industrial project assessments. The paper concludes by summarizing the current state of mining project readiness assessments, the unique and differentiating factors to be considered, and suggests recommendations towards the development of generalizable readiness assessment criteria for mining projects.

Sep 1, 2022

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By John C. Ferm

This report summarizes the results of an investigation of geologic factors that contribute to roof quality in underground mines in the Pocahontas #3 coal bed in southern West Virginia and southwestern Virginia. The investigation consisted of three phases, the first of which was selecting for detailed study five mines which represented the range of roof conditions, mining practices and geologic phenomena. This was accomplished by a statistical analysis of questionnaire data from 35 mines. The second phase consisted of detailed mapping in a "good" and a "bad" top area in each of the five selected mines and resulted in a qualitative assessment of geologic factors contributing to roof £alls. In the third phase, five mines were selected in which most non-geologic factors believed to contribute to roof falls were relatively constant but displayed a wide variety of geologic characteristics. Data from these mines were analyzed to test the qualitative assessments from Phase II. The primary result of this investigation is that slickensides arising from different geologic causes are the major geologic features leading to roof falls. These slicken-sides are found in ancient slump deposits, fire clays and sandy fire clays and channel contacts. Falls also occur where thick sandstone bodies directly over-lying the coal contain abundant shale or ironstone pebbles and coaly strips. The best top material is a sequence which consists of shale grading upward to sandy shale and sandstone within 30 feet of the top of the coal. Thick sand-stone units (301) without pebbles also provide good top.

Jan 1, 1978

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By Keith L. Harris

The economy continued to expand during the second quarter, but at a much slower pace than expected. According to latest estimates released by the Department of Commerce, the real gross national product (GNP) grew at a seasonally adjusted annual rate of 0.6% compared with a revised growth rate of 3.8%2 for the first quarter of 1986 and 2.3% for the second quarter of 1985 (table 1). The strong growth of personal consumption expenditures, Government purchases of goods and services, and residential investment was moderated by the growing trade deficit, declining investment in business inventories, and the continuing lag in nonresidential investment. Much of the decreased capital spending for the nonresidential sector for the first and second quarters resulted from reduced petroleum exploration and drilling in response to low petroleum prices. Capital spending and trade continue to be areas of weakness for the economy. Real new plant and equipment expenditures for 1986 are estimated to be 1.3% below those of 1985 (table 2). Real net exports of goods and services decreased $24.6 billion, as exports declined 5.6% and imports grew 16.5%. About two-thirds of the $19.3 billion increase in imports was in petroleum and petroleum products, which, because of their lower prices, should help the economy in the future. In response to the sluggishness of the economy, the Federal Reserve System reduced its discount rate from 6.5% to 6% in early July. Inflation, as measured by the fixed-weighted GNP price index, declined from a revised 2.5% in the first quarter to 1.9% in the second quarter because of significantly lower energy prices.

Jan 1, 1986

By Christopher J. Bise

Introduction In August 1977, the federal Surface Mining Control and Reclamation Act was signed into law. It stated that: "The Congress finds and declares that because of the diversity in terrain . . . and other physical conditions in areas subject to mining operations, the primary governmental responsibility for developing. authorizing, issuing, and enforcing regulations for surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environmental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall require the operator to adopt measures consistent with known technology in order to prevent subsidence. causing material damage, to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining." This section raises many questions. Precisely what is the "reasonably foreseeable" future as far as land use is concerned? And what is the "standard method of room and pillar mining"? The first part of the paragraph seems to rule out longwall mining, but isn't longwalling a "predictable" manner of "planned subsidence"? Does the Act take into account variations among mining methods in differing regions or coal seams? With these questions and the need to comply with the Act's provisions in mind, many states may turn to the Pennsylvania Bituminous Mine Subsidence Act of 1966- the only comprehensive subsidence act passed by any state-as a model for their own programs. Thus, it is very important to evaluate Pennsylvania's Act to see whether its basic assumptions can accommodate national application. This paper will note the Subsidence Act's provisions and guidelines, briefly analyze the current state-of-the-art in subsidence damage prevention and control, and list several recommendations for altering the Act's application guidelines for different mining areas.

Jan 1, 1982

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By M. E. Poad

In 1986, a cooperative effort by the Homestake Mining company, the U.S. Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will be safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modelling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1994

By V. H. Gottschalk

Among the procedures developed by the Germans for providing the tonnage of iron powder needed to make rotating bands for artillery shells is the use of a ceramic tunnel kiln, not only for finishing the reduction of centrifugal powders but also for making so-called "brickyard sponge iron," which, after crushing and grinding, seems to yield a product suitable for powder-metallur- gical purposes. The final report issued jointly by the German Powder-Metallurgical Society (DPG) and the Chemical-Metallurgical Branch of the Research Depart- ment of the Metallgesellschaft, Inc. (ZFC of MG) gives the available details of this procedure, which may be regarded as a further development of the process in commercial use since 1911 at a ceramic plant in Hoeganaes, Sweden. The Bureau of Mines' wartime development of the Hoeganaes process also cul- minated in the adaptation of ceramic tunnel kilns for carrying out the solid- carbon reduction of iron ores, and comparison with the German technique should further advance the art. This information circular is issued as a supplement to Bureau of Mines reports of investigations Nos. 3819,2 3822, 3841,2 and 4271, on brick- yard sponge iron and is based on four German reports entitled "Making Iron. Powder in the Tunnel Kiln," translated from FIAT microfilm reel H-46, frames 9190-9209, 9280-9299, 9339-9357, and 9377-9384 (PB L 70042), which represent the four original research reports, Nos. 2005, 2008, 2010, and 2012, respec- tively, of the Metallgesellschaft, Inc.

Aug 1, 1948

By Eldon C. Pattee

THE BUREAU OF MINES began an investigation of tungsten resources of Montana in September 1953. This report presents information obtained from July 1955 to September 1957 on tungsten deposits in and near the Mount Torrey batholith. The batholith comprises part of the Pioneer Mountains of Beaverhead County in the southwest corner of Montana. Included in the report are assays and preliminary-examination data on 22 properties. Tungsten minerals are known to occur in 19 of the properties. The major producer is the Brown's Lake mine which has produced more than 625,000 tons of ore. Nearly all of the deposits are in the Lost Creek, Utopia, and Bald Mountain mining districts along the east and south margins of the Pioneer Mountains. The districts are less than 27 miles from Dillon, Mont.

Jan 1, 1960

By R P. Douglas

During 1955, Cominco commenced an exploration pro-gram in northern New Brunswick; in the following year, what is now the Wedge mine was discovered. The mineralization is mainly pyrite, with associated chalcopyrite and minor amounts of sphalerite and galena. The property was brought into production at 750 tons per day in early 1962. The ore is trucked 10 miles to the Heath Steele concentrator, where a copper concentrate grading about 19.5 per cent is produced and shipped to the Japanese markets through the port of Dalhousie, New Brunswick. Introduction THE Wedge mine, owned by The Consolidated Mining and Smelting Company of Canada Limited (Cominco), is located in the Newcastle-Bathurst area of New Brunswick. It is 42 miles by road northwest of Newcastle and 37 miles southwest of Bathurst (Figure 1). The mine is located on the north side of the Nipisiquit river in one of the more mountainous areas of the Province, the local relief rising to 1,500 feet above sea level. There is an almost complete forest cover of mixed hardwoods and conifers -the val-leys and hillsides being covered by balsam, spruce and pine, the swamps by cedars and black spruce and the highlands by mixed hardwoods.

Jan 1, 1965

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By Thomas Varley

"The literature on flotation of oxidized ores except for patents (especially for reagents) is very sparse. The Bureau of Mines in 1936, published a circular on the subject, by Ralston and Allen. The treatment of oxides by flotation was then in its infancy, but several of the most important mining companies in the Western United States and Mexico are now operating flotation plants for treating oxidized ores. The purpose of this present circular is to review the progress made and bring the subject up to date. One of the writers of the 1916 report (Mr. Allen) has been associated with some of the most important mining companies who have put into practical operation the process of flotation of oxidized ores; among these companies are the Shhttuck Arizona Copper Co., Bisbee, Arizona (now the Shattuck Denn Co.) and the San Francisco Mines of Mexico, Ltd., San Francisco Del Oro, Chihuahua, Mexico. His experience and other sources of information have been freely drawn on in pre-paring this paper. Mr. Ralston, assistant chief metallurgist of the Bureau of Mines, contributed many valuable suggestions and criticisms.Sulphidizing Reagents for Oxidize Ores.The various reagents and methods that might possibly be used for sulphidizing were summarized by Ralston and Allen as follows:""Sulphidizing (1) by the use of hydrogen sulphide on either the dry or the wet crushed ore, (2) by the use of solutions of the various sulphides and sulpho-compounds of sodium, (3) by the use of solutions of the various sulphides and sulpho-compounds of calcium, (4) by the use of sulphur vapor, (5) by the use of a sulphureted oil, (6) with colloidal sulphur."

Jun 1, 1927

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019