Search Documents

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited avail- ability in certain areas. Limestone and dolomite are so useful and so abundant that in 1972 more than 690 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our recent report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1975

By Robert C. Freas, Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodities in this volume have as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as aggregates, fluxes, glass raw material, refractories, fillers, reactive agents in sulfur-oxide removal, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Holocene. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1989 about 798 Mt were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses. The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1994

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Warren E. Wilson

THE transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. ENERGY. REQUIREMENTS Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: [Solids load in terms of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m, Mass per unit volume of liquid by ml Mass per unit volume of mixture by m,,, We then have as an expression for the solids load: W = pQm¬] The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1945

EARLY in 1911 the Public Service Board of New South Wales suggested the advisability of inaugurating a School of Mines at Broken Hill, arid made inquiries to determine how such an institution should be conducted. He, the author, believed the Board, as a result of the inquiries, was in favour of the project being worked in conjunction with the Technical College, and hoped to be ready to receive students at the commencement of 1912. That the inauguration has not yet taken place is probably due to the vast amount of consideration and preparation that a new departure of the sort would require. At the present time New South Wales or, to speak more broadly under the same denunciation, Australia is not at all suitably catering for the technical training of young men to provide the increasing demand for officers to work the valuable mines within its territory...

Jan 1, 1912

By A. K. Das, S. Pathak, C. Bhanu, P. K. Tripathy

Ferroalloys are integral part of steel melting process. The purpose of using ferroalloys is three fold e.g. killing of steel, modifying the slag composition and steel alloying. Amount of ferroalloys used for alloying is subject to requirements of steel properties e.g. yield strength, ductility, formability etc. Variety of ferroalloys (some-times pure metal) is used by steel industries depending upon their techno-economic feasibility. Size, chemistry and modes of addition of ferroalloys are suitably engineered to bring in operational consistency and cost benefits. Of late, Tata Steel has tried out a few ferroalloys for the first time with interesting results to meet the specific requirements of high strength interstitial free (IF) and micro-alloyed steels. Some of these ferroalloys have been put into regular use with complete or partial replacement of ferroalloys used earlier. Size of one of the ferroalloys has also been modified without any other adverse effects. This paper summarizes requirements of ferroalloys for the steel industry with special emphasis on recent trials.

Jan 1, 2007

A series of fault slip seismic events have occurred at Garson mine. The events have occurred during development advancement exposing faults, after the extraction of single stopes due to mining induced stress change, and due to time effects after delays of many days during which no mining had been conducted. This paper discusses the study completed consisting of a global or holistic approach aimed at mitigating some of the risks associated with the structurally controlled rockbursts at Garson. Background Garson mine is located in the south east area of the Sudbury Basin (Ontario, Canada). Mining occurs in two main ore bodies (the #1 Shear and the #4 Shear) which are copper-nickel-sulphide and occur within shear zones that (as well as the ore bodies) strike approximately east-west and dip steeply south. From the north (footwall), lithologies progress (Figure 1a) from norite (NR), to greenstone (GS), and finally to meta-sediment (MTSD). A generally WNW-ESE striking, bifurcated sub-vertical dyke of olivine diabase (OLDI) cuts the series. The current active mining block at Garson is between 4700L and 5100L (levels denote depth in feet below surface).

May 1, 2009

By P. N. Worsey, M. Schmidt

Many advanced military systems and civilian power generation concepts postulate the availability of compact sources of electrical power capable of delivering gigawatts over microsecond time scales. For example, such a compact power source is essential for future practical pulsed high-powered microwave sources. An explosive-driven flux-compression power generator (EDPG) could fill this requirement. A basic strength of this concept capitalizes on the inherent high energy density storage capacity of modern chemical explosives. It relies on the physics of magnetic flux compression to convert that stored chemical energy into very large amounts of electrical power over short time scales. The generator also has the additional advantage of employing the same types of explosives that are already routinely used in conventional munitions. However, the self-destructive nature of this type of power generator places serious limitations on power pulse-lengths and ranges of applications. This paper describes how a multi-disciplinary team led by researchers from the University of Missouri-Rolla (UMR), Texas Tech University (TTU), and Texas A&M University was awarded a grant by the U.S. Air Force Office of Scientific Research to perform basic research to resolve several fundamental EDPG problem areas. Described are the utilization of UMR’s extensive explosives research expertise and facilities to investigate questions of energy conversion efficiency and the mechanics of energy production. Also, UMR explosives researchers will provide inputs to improved dynamic computer models of the complex, intertwined physics and chemistry operative in these devices. In addition to explosives expertise, UMR provides facilities for basic explosives material research, as well as the storage, machining, and formulation of explosives. UMR researchers are also using test facilities and data collection equipment at the Rock Mechanics and Explosives Research Center and at the UMR Experimental Mine to perform “proof of principle” and subscale tests of explosive-driven flux-compression power generator components. An integral part of the paper is a description of the development of an extreme intensity flash system by UMR and TTU to allow for the high-speed photography of EDPGs in operation. This multi disciplinary research program offers major advances regarding the size, weight, and electrical characteristics of compact EPDGs. Such breakthroughs could dramatically accelerate the practical realization of systems currently under study. Also, these power sources may have far reaching relevance to other Department of Defense and certain commercial compact power applications.

Jan 1, 2000

By G. L. Tufford, R. L. Bleifuss

Low-grade manganiferous iron ores of Minnesota's Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite with subsequent magnetic separation and flotation have not given satisfactory results because, in many instances, concentrate grade and manganese recovery are low. Metallization of iron and concurrent reduction of higher manganese oxides to MnO, as in the R-N process, followed by recovery of iron by magnetic separation and manganese by leaching, seems to be a technically feasible process. High-temperature x-ray diffraction studies show that solid-state reactions between iron and manganese, with the formation of intermediate iron-manganese oxides, occur during reduction and affect recovery of both iron and manganese from the final product. Solid state reactions also occur between FeO, MnO, and SiO, at temperatures as low as 900°C. The kinetics of these reactions are such that they become an important factor in the treatment of ores by the R-N process. These investigations suggest a temperature and gas composition cycle that would maximize both iron and manganese recovery. During the past ten years, iron ore shipments from the Cuyuna Range of Minnesota have decreased sharp1y. Because of adverse grade, structure, and cost, many Cuyuna ores are no longer competitive with high-grade foreign ores and domestic pellets. The low-grade manganiferous iron ores from the Cuyuna Range, in general, do not respond to conventional mineral dressing techniques because of their fine-grained texture. Reducing these ores to magnetite for subsequent magnetic separation and flotation has not given satisfactory results because concentrate grade and manganese recovery are often low. However, a technically feasible process appears to be metallization of the iron and concurrent reduction of manganese oxides to MnO with recovery of metallic iron by magnetic separation and extraction of manganese from the tailings by leaching. In 1962 the R-N Corp., with a grant from the Area Redevelopment Administration, conducted an amenability study of the metallization of manganiferous iron ore from the Cuyuna Range. The results of this preliminary investigation were sufficient to interest the Economic Development Administration in sponsoring further studies of the process with emphasis on secondary recovery of manganese from the nonmagnetic tailings. Inasmuch as the metallization process has considerable influence on the final form of the manganese - its texture and distribution between the magnetic concentrate and nonmagnetic tailings-the investigation included a study of metallization of the ore as well. Therefore, the investigation conducted at the Mines Experiment Station covered three interrelated phases: (1) laboratory R-N roasting studies and magnetic separation tests, (2) laboratory chemical extraction experiments of the nonmagnetic tailings, and (3) a mineralogical study of the crude ores and their various roast products. High-temperature x-ray diffraction investigation of the Fe-Mn-Si0,-0, system is the main topic of this paper and an extension of the mineralogical work. GENERAL GEOLOGY The Cuyuna Range is known for its complicated geologic structure, complex orebodies, and generally indifferent response to attempts at conventional beneficiation. Several geologists have made intensive studies of the Cuyuna Range, including Leithl (1907), ~darns' (1910), Zapffe3 (1925), Grout and Wolff4 (1955), and schmidt5 (1963), whose study was the most comprehensive of all. The Range is covered with glacial deposits - till, out-wash, and lake sediments -up to 250 ft thick. Bedrock stratigraphic units of the Cuyuna Range consist of three tightly folded Precambrian sedimentary formations. The lower unit is the Mahnomen formation, composed of 2000 or more feet of argillite, slate, siltstone, and quartzite. The middle unit is the Trommald formation, which varies from 45 to 500 ft in thickness and comprises the major iron-bearing formation. The upper unit is the Rabbit Lake formation, consisting of over 2000 it of argillite, slate, and interbedded lenses of lean iron formation. In the central part of the Cuyuna Range, the units have been folded into a series of

Jan 1, 1969

By Art Cooper

Granulation systems are common in the metals industry. The process of granulating slags, mattes and metals is more than a century old, and a number of different systems have been developed to accomplish this task. These systems have followed an evolutionary path, and may be characterized by common elements in terms of molten material handling, granulation methods and post-granulation processing. This paper will summarize the more common systems used in the metals industry, with particular reference to non-ferrous applications.

Jan 1, 2006

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By K. Hanumantha Rao, K. S. E. Forssberg

The limestone deposit of Gâsgruvan, Sweden contains around 89.2 per cent of calcite. Conventional and column flotation studies have been carried out using sodium oleate and modified fatty acid collectors in the presence of sodium silicate modifier. The effects of collector and silicate concentrations, and particle size on the flotation response of calcite have been investigated. The results have been discussed in comparision to the performance of conventional and column flotation cells. The feed size is found to be a significant factor to achieve a high grade calcite concentrate either by conventional or by column flotation. The loss of selectivity at fine particle sizes is examined using a modified DLVO theory.

Jan 1, 1995

By Rich Perry

HARRY HINDS: Our second speaker today is Rich Perry. Rich is the manager of leach and dewatering at Newmont Gold Company's Carlin operations. He has been the operator of Newmont's refractory leach development program for the past three years. Prior to joining Newmont in 1994, he was plant superintendent at the Big Springs and Jerritt Canyon Roasting Mills for Independence Mining Company. He graduated from the University of Nevada's Mackay School of Mines, and has lived with his wife and three children in Elko, Nevada, for the past 12 years. Please welcome Rich as he presents "New Facility Design Engineering: On-Site Versus Engineering Companies' Offices." RICH PERRY: Newmont Gold Company has been mining and processing gold ore at its Carlin, Nevada, operations since 1965. Processing is done using oxide milling, heap leaching, and whole ore roasting methods. Newmont began development of refractory leach processing technology at its research and development facility in 1988. The R&D staff focused on developing processing methods for low-grade refractory gold resources at Carlin that could not be economically processed by refractory milling methods. The term refractory ore refers to those ores that contain quantities of sulfides and/or organic carbon that result in low recoveries using conventional cyanide leaching. The R&D staff developed two potential processes deemed worthy of further testing: heap biooxidation to liberate gold occluded by sulfides and ammonium thiosulfate leaching for gold recovery from carbonaceous preg-robbing ores. These were piloted in small heaps by the staff of the R&D and Carlin metallurgical labs from 1990 through 1994. By 1994, Newmont's R&D and metallurgical staffs had unlocked the chemistry and kinetics of the two processes, and it was decided that the operations group would be brought in to begin development of a commercial plant. A project manager at Newmont's Denver office was assigned to the project. Scale-up issues such as biooxidation leach pad design; on/off heap heights; handling of various ore types during stacking and reclaiming; operating costs; and environmental, health, and hygiene concerns using a new process chemistry remained unanswered.

Jan 1, 1998

By Don M. Jackson, Robert W. Howard

Techniques for the epilaxial growth of single -crystal silicon carbide films on silicon were developed. The vapor-phase decomposition and bydrogen reduction of silicon tetrachloride (SiC14) and Propane (C3H8) resulted in clear films of silicon carbide, lip to seveval microns in thickness. The growth took place in a horizontal . silicon epilaxial reactor at 1100°C (pyrometer) at a rate of- 3000Å per minute. Electron diffraction and X-ray diffraction studies demonstrated that the films were single-cyrstal, ß -phase, or cubic silicon carbide. SiO2 film were used to mask areas of the silicon sur-lace in order that the silicon carbide might be grown in controlled geometries. Both n- and p-type films were grown on p-type silicon waters.. Heavily doped silicon films of the same conductivity type as the silicon carbide films were deposited over the silicon carbide in order to affect better probe contact to the structures. when n-type silicon carbide mesas were grown on p-type silicon substrates the de vollage-current relationships between films and substrates were that of junction diodes. These diodes showed a sensitivity to while light ill that the incident light increased forward- and reverse-satro,ation currents, P-type silicon carbide mesas grown on p-type silicon were ohmic rather than rectifying in their voltage -current relationship. No conclusions could he reached concerning heterojunc-tiou rectification in the structure. SILICON carbide is a semiconductor with many interesting properties. It decomposes at temperatures above 2200°C.1 It occurs in two general crys-tallographic forms—hexagonal (a Sic) and cubic (ß Sic)—with the cubic form having a forbidden-gap energy of 2.32 ev and the hexagonal form (specifically the 6H polytype) a gap energy of 2.86 ev.3 It behaves as an extrinsic semiconductor at temperatures approaching 5003C. It has been shown to have a high resistance to radiation damage4 and p-n junctions formed in Sic have been shown to radiate visible light under forward- or reverse-bias conditions. Epitaxial silicon carbide on silicon carbide has been successfully grown through the use of a variety of techniques, such as gaseous cracking of SiCL4 and CC4, nearly all of which require a deposition temperature above 1500°C.6 This paper will cover very recent work on the gas-phase deposition of highly ordered films of silicon carbide on high-quality silicon single-crystal substrates. The films have been shown to ex- hibit junction-rectification properties when geometrically isolated regions are electrically biased with reference to the silicon substrate. There will be no discussion of the mechanism of heterojunction rectification, but the methods of film fabrication, geometry control, and structural evaluations will be covered in detail. Electron diffraction, X-ray diffraction, and diode electrical properties were used to characterize the films and the junctions. GAS-PHASE DEPOSITION OF Sic The techniques for the deposition of silicon carbide films were a logical outgrowth of the standard silicon epitaxial process. The major premise followed was that, for any film to nucleate in an ordered fashion where there is considerable mismatch in lattice parameters (in this case 22 pct), an extremely clean, damage-free substrate surface must be presented to the gas stream. Thus a standard gas-phase HCl etching step was used to prepare the substrates for growth. A minimum of 5 µ of substrate-surface material was removed prior to the deposition of Sic overgrowth films. The techniques used for growing silicon carbide films were those of growing silicon alone, with the added injection of a hydrocarbon gas into the hydrogen and silicon tetrachloride gas stream. The hydrocarbon gases used thus far have been research-grade (99.99 pct) methane (CH4) and propane (C3H8). Propane ultimately gave the best results. The gas flows were controlled through a panel shown schematically in Fig. 1. A hydrogen main stream of 30 liters per min passed through the horizontal quartz-tube epitaxial reactor, while SiC14, C3H8, HC1, and doping gases were injected as side streams. The

Jan 1, 1965

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the 'contract' system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By John Pilling

The concept of microstructure, its evolution through materials processing and its effect on the properties of the material is, perhaps, the foundation upon which the science of materials is built. PHAUST, a computer aided learning program, attempts to provide instruction in establishing the relationships between phase diagrams, thermal processing and microstructure. Using phase diagrams derived from a database or created by the user, the evolution of microstructure during processing is quantified using the lever rule and/or the Scheil equation and tracked through a doubly linked list (a form of binary tree). Microstructures, in the form of full colour cartoons are then drawn using the quantitative and logical information contained within the linked list using bitmapped templates and logigal operators such as NOT. AND, OR and XOR, giving the student a view of the structure as it would be seen under the optical microscope. The software provides complete diagnostics of student answers, locates errors and misconceptions as well as providing tutoring towards the correct solution method and answer.

Jan 1, 1991