Search Documents

By J. M. W. Mackenzie, C. J. Wood

In attempting to describe the size classification performance of a hydrocyclone, most workers have elected to use either an equilibrium orbit theory or an non-equilibrium orbit theory. The equilibrium orbit theory has been used by the majority of workers including Lilge,' Bradley; and Yoshioka and Hotta. In applying this theory, it is argued that particles in the body of a hydrocyclone attain an equilibrium radial position where the drag force on the particle resulting from the inward radial fluid velocity is balanced by the outward centrifugal force caused by the tangential component of fluid flow. When considered over the full height of the hydrocy-clone, attainment of this radial equilibrium orbit results in the particle following a conical equilibrium envelope. It is then argued that if this envelope lies outside the envelope of "zero vertical velocity," the particle will report to the underflow, while if the equilibrium envelope lies inside the envelope of "zero vertical velocity," the particle will report to the overflow or vortex finder product. The d50-sized particle which reports in equal quantities to the underflow and overflow is assumed to correspond to particles whose equilibrium envelope is coincident with the envelope of "zero vertical velocity." In considering the equilibrium orbit theory, it is apparent that the horizontal position of the particles in the feed inlet pipe should have no effect on their ultimate destination on the hydrocyclone. Each particle should attain an equilibrium position which depends on the density, size, and shape of the particle; the density and viscosity of the fluid; and the flow patterns within the hydrocy-clone. The nonequilibrium orbit or unsteady state theory has been largely developed by Rietema4 and Mizrahi.6 Mizrahi has listed four main objections to the equilibrium orbit theory. These objections center on the short residence time in the hydrocyclone, the fact that the experimental classification curve is much less sharp than is theoretically predicted, and the absence of negative efficiency conditions in hydro cyclones operating on a feed material which is much finer in size than d50. Proponents of the nonequilibrium orbit theory argue that for a particle to discharge with the underflow it must have sufficient outward radial velocity to reach the downward-flowing region close to the hydrocyclone wall in which the flow lines are parallel to the wall and the ratio of vertical to radial velocity is constant. It is then postulated that a d50 particle entering the cyclone at the center of the feed inlet will just reach this downward-flowing region as it reaches the apex. Thus for uniform distribution of particles across the feed inlet, half the d50 particles—that is, those injected in the half of the inlet area nearest the cyclone wall —will report to the underflow while those injected in the other half will not reach the downward-flowing region and will be carried inward to the center of the cyclone and thus report in the overflow. The exact thickness of the down-ward-flowing region of fluid adjacent to the outer wall of the hydrocyclone is uncertain but Mizrahi considers it to be equal to the apex radius minus the air core radius. Particles larger than d50 have a greater outward centrifugal force acting on them than the d50 particles and may reach the wall even if injected at a distance from the wall greater than Di/2 (Di is inlet diameter). Conversely, particles smaller than d50 may not reach the wall even if injected at a distance less than Di/2 from the cyclone wall. Since the equations put forward by the proponents of both theories yield approximately the same values of d50, it is not possible to decide between these theories by measurement of d50. It should be possible however to examine the theories by injecting a small stream of solids into the feed inlet of a hydrocyclone running on clear water. If the efficiency or classification curve is measured for various horizontal injection positions, then the curves should be coincident if the equilibrium orbit theory holds. If, however, the unsteady state theory describes the cyclone operation, then the classification curves should show finer d50 sizes for particles injected close to the cyclone wall. Experimental A 6-in.-diam hydrocyclone with geometry as in Figs. 1 and 2 was used. Quartz particles were injected as a 50% by wt pulp via an 1/8-in. steel probe. For each in-

Jan 1, 1971

Lower costs associated with hands-on training in donning and using a CSE ,self-contained self-rescuer (SCSR). Background In June 1987, the Mine Safety and Heath Administration (MSHA) issued an Emergency Temporary Standard (ETS) requiring that all persons entering underground coal mines must be given bands-on SCSR training. The ETS will shortly be replaced by a new standard requiring this hands-on training. Bureau of Mines research has shown that the most effective means of delivering this training is to have the trainee go through a six-step training procedure while in a kneeling position. Once the miner has looped the neckstrap over his or her head, he or she completes the donning sequence in this order: 1) activate oxygen; 2) insert mouthpiece; 3) put on nose clips; 4) put on goggles; 5) adjust neck and waist straps; and 6) replace miner's cap and prepare to move out. This procedure is repeated until the miner demonstrates that he or she is proficient at the task.

Jan 1, 1988

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

By R. N. Chakravorty

Environmental monitoring plays a key role in coal mine safety. In recent years, significant advances have been made in the development of systems suitable for monitoring air in underground coal mines. Because of intensive mining and large capital outlay, the need for higher productivity consistent with safety is well recognized and it appears that environmental monitoring may help achieve this objective. This paper reviews the state-of- the-art in the monitoring technology with particular reference to hazardous gas detection in underground coal mines. The preliminary results obtained from ongoing studies, with regard to continuous monitoring of methane and carbon monoxide in mine air in some of the operations in Western Canada, are discussed. The inadequacies of the methods using spot samples are examined and the need to supplement the present practice with continuous monitoring systems is emphasized.

Jan 1, 1979

By C. W. JEFFERS

During the past few years the use of mechanical equipment for the loading and transportation of coal at the working face has rapidly increased . Many mining officials are of the opinion that mechanical methods have tended to reduce the hazards of mining, and a number of statements have been made to this effect . Little actual data upon which to base conclusions in regard to the relative safety of various methods of mining have been made available . While it may be possible that these systems of mechanical mining are inherently less hazardous , obvious dangers should not be disregarded in the belief that the mere act of installing mechanical loading equipment automatically brings about better accident records . The same rules and regulations , modified to meet the new regime must be applied with the same discipline as heretofore . By diligent study and application there is reason to believe that new methods of concentrated mining can be utilized with at least a possibility of increased accident performance . With the idea of preventing accidents by taking available precautions against their occurrence , attention should be directed to the dangers that exist where room and face conveyors are in operation . Due to the cost pressure prevalent in the mining industry at the present time mechanical means are often used in an attempt to decrease cost of production. The management , after having spent considerable sums of money for new equipment , is expected by stockholders and investors to show results by increasing tonnage and reducing operating costs . Consequently the operating officials apply the same pressure to local mine officials to obtain results . The natural reaction of the superintendent and mine foreman is to secure the maximum production from the new method , and unfortunately safety is frequently , if not generally , sacrificed to this end . In many instances , operators of new types of mechanical loaders are difficult to secure and after being obtained are difficult to hold , especially if the new equipment is more or less in the experimental stage . The tendency is to handle the machine operators with " gloved hands " and to permit many unsafe practices which ordinarily would not be allowed, in order to keep from antagonizing them and losing their services . Although these unsafe practices become habitual and even uneconomical , conditions thus established are difficult , sometimes impossible , to change .

Jul 1, 1930

By Warren D. Longwill

All known resources within the four proposed RARE II additions to the Yolla Bolly-Middle Eel Wilderness in northwestern California occur in the Gig Butte-Shinbone study area (fig. 1). No mineral resources are Figure 1.--NEAR HERE. known in the East Fork, Murphy blade, or Wilderness Contiguous units. About 2,400 tons (2,177 t) of subeconomic manganese resources averaging 9.5 percent manganese have been estimated at the Blue Jay Mine in the Big Butte-Shinbone unit. In addition about 9,700 tons (8,793 t) of subeconomic chromium-nickel-cobalt resources in thin laterite soil at the Grubstake Prospect contain about 1.27 percent chromium oxide, 0.45 percent nickel, and 0.03 percent cobalt. Adjacent Ultramafic rock outcrops have pods averaging 2.5 percent chromium oxide (Cr203); one pod contains about 40 tons (36 t) of indicated subeconomic resources.

Jan 1, 1981

By C. Newman

"As underground mining continues to operate at deeper depths and in more complex multiple seam mining geometries there has been an increased demand for higher design standards in ground control safety and stability within the mining industry. For the past 20 years, NIOSH has developed and validated a number of software tools to aid in the development of safer mining environments with respect to improved roof support performance, pillar stability in longwall and room and pillar mines, formation characterization, the prediction of roof conditions, etc. These tools are available, free of charge, to the mining industry as stand-alone software packages. As cloud computing gains momentum, there is a definite need to develop internet based applications for mine design that would be easily accessible to any user at any time, including underground where permitted. This paper introduces a new web-based product which will allow for faster and easier access to existing ground control designs, on-the-fly calculations in the field as needed, and instant online collaboration between operations personnel and planning engineers. It is expected that the industry will rapidly embrace this product and, as it is common with all new innovative technologies, it will be a new paradigm for mining engineering computer applications. INTRODUCTION Since its release to the public in the late 1980's, the World Wide Web has drastically changed from a collection of static HTML web pages to a dynamic vehicle driving e-commerce, collaborative working relationships, and the mass distribution of information and media (Offutt, 2002). Recent developments in Internet capabilities, such as Cloud Computing and Software as a Service, have begun a migration away from desktop-based software in adoption of the web application (Hayes, 2008). Web applications, or web apps, are designed on the client-server architecture paradigm in which the client, or user, can interact with an application through web browsers without disrupting or installing software on potentially thousands of client computers (Nations, 2015). Currently, web-based software applications are being utilized in all business sectors and markets from commerce, finance, media, and even engineering. In fact, the Alabama Department of Transportation has developed a web-based geotechnical geographical information system (GeoGIS) for the management of and access to geotechnical and subsurface data for transportation projects across the state (Graettinger, et al., 2001). Similarly, Dyno Noble has developed a service application for explosive engineers. The Explosives Engineers' Guide application equips users with a full range of product information as well as on-demand blasting calculations for powder factor, airblast prediction, ground vibration, etc. Through the incorporation of a web server, one is able to utilize the functionality of the desktop-based software through a web browser located on any personal computer, tablet, or Smartphone (Vaughan-Nichols, 2002)."

Jan 1, 2016

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200, 000+-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced, The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 200 I. As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By R. Havens

During investigations of the occurrence of manganese in the western United States in the early 1940?s, examining engineers of the Bureau of Mines collected samples from seven claims and mines in southern Arizona. For convenience in reporting the results, the work on the properties is grouped in three districts. As the ores were too low grade to be acceptable to producers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The San Fernando group is about 10.5 miles south of Patagonia in the Harshaw mining district. G. T. Humphries and D. Alonso held an option on the property, which was owned by H. Bender. Two samples were taken; 1 was a picked sample and the other a representative sample of ore as exposed in the mine.

Jan 1, 1954

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016

By G. F. Jenkins

ASBESTOS is a general term embracing the fibrous varieties of a number of minerals. Of these, the hydrous magnesium silicate, chrysotile (H4Mg3Si209), a variety of serpentine, is the most abundant and useful to industry. All other types of asbestos belong to the amphibole group of minerals and are classified as: crocidolite, NaFe(SiO3), FeSiO3; anthophyllite, (MgFe)SiO3; amosite, also a ferromagnesium silicate but with iron content higher than that of anthophyllite; tremolite, CaMg3(SiO3)4; and, actinolite, Ca (MgFe)3(SiO3)4. PROPERTIES The commercial value of asbestos depends largely on the physical property that permits it to be readily separated into fine filaments of high tensile strength and flexibility, which, coupled with the fact that it has the quality of incombustibility of a mineral-in distinction to vegetable and animal fibers-makes it of unique usefulness for many purposes. To some extent, the value depends upon the length of the fiber, although extreme length is neither necessary nor desirable for most purposes. Chrysotile occurs as cross-fiber veins, in which the asbestos fibers are approximately' at right angles to the vein walls, with vein width- or fiber length-seldom exceeding 2 or 3 in.; also as slip-fiber, in which the fibers 'lie in the same plane as the vein or on slippage planes. A cleanly broken vein of cross-fiber has a pearly luster and may range from a deep green or brown color to light shades of yellowish green or cream. When of good quality, the fiber filaments forming the vein may be easily drawn away from their neighbors and exhibit a fine silkiness and pure white color. They may be twisted into a thread and when flexed between thumb and fingers are found to be strong and pliable. Chrysotile withstands comparatively high temperatures without breaking down completely or fusing but begins to lose water of crystalliza-

Jan 1, 1949

By Robert F. Chaiken

The Bureau of Mines is using model ducts lined with coal to study the nature of coal mine fires, their rate of propagation, their influence on ventilation airflows, and their response to sealing and other fire suppression measures. For scale-modeling purposes these studies are being carried out in various size ducts; eventually they will include a full-size mine entry in the Bruceton multiple-entry Experimental Mine. To date, work has been carried out in an insulated 9.l-m-long duct with a 5-cm thickness of coal leaving a 23-by 23-cm square opening for air ventilation. Fire propagation processes in this duct were mainly transient in nature owing to the relatively small length-to-diameter ratio. This report describes the experimental equipment employed and the results obtained to date.

Jan 1, 1979

By R R LARGE

In the past decade mineral deposit models have become an important tool for the exploration geoscientist. By combining genetic theories on the formation of particular deposit styles, with geological, geochemical and geophysical criteria relevant to ore location, it has been possible to more effectively focus exploration effort to the regions and local targets which have the best chance of success. However, such models have their limitations, and must be carefully and critically applied and continually updated as new technical and research information becomes available.

Jan 1, 1992

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1974 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

By Brian W. Mackenzie

The paper addresses five questions concerning the economic of gold exploration in the western Canadian shield. Can historical footprints be used to project future gold prices for exploration planning? Experience suggests that gold price forecast are too clo ely tied to current market events to provide meaningful guidelines. What range of breakeven gold price will typically be required to ju tify gold exploration in Canada? Minimum price requirements. initially asses ed at $540 to $1080 per ounce, probably lie in the range of $480 to $760 per ounce (expressed in 1985 Canadian dollar). Within Canada, what role do regional conditions and taxation policies play in determining the viability of prospective gold exploration targets? Striking interprovincial differences are found to exist, given the same geological circum tance -Nova Scotia, ew Brunswick, and Quebec rank towards the top in term of motivating exploration, Briti h Columbia provides the least investment incentive, while Saskatchewan and Manitoba place around the middle of the Canadian league. How can minimum acceptable tonnage-grade conditions for gold targets in the western shield be established and, then, constructively applied to provide exploration planning guidelines? Minimum target conditions, realis tically defined in terms of a broad band of doubt, can be used judiciously to help balance the direct costs of uneconomic exploration with the opportunity costs associated with rejecting economic deposits. How does the average cost per ounce of gold discovered in the western shield compare with the overall Canadian experience? Average discovery costs for the we tern shield, apprai ed at $100 per ounce, are shown to compare favourably with the Canada-wide record.

Jan 1, 1986

By J. Visman

The water cyclone washer has a number of advantages that makes it a desirable machine for the cleaning of fine-grained and friable materials such as 1,4 x 0" slack coals. In this paper results are presented of tests carried out on a shaly coal containing a high percentage of inter-grown materials from the Minto area, New Brunswick. The tests were con-ducted in the pilot plant of the Western Regional Laboratory in Edmonton. The test results show that the cleaning characteristics of this coal can be improved by lightly grinding the recirculating middlings fraction, which constitutes approximately 30 per cent (1.45-2.00 fraction) of the raw feed. • The cleaning of 1;4 x 0" fines by water cyclones compares favourably with other coal cleaning machines and has an added advantage of being extremely simple to operate, low in capital and operating cost, and high in capacity. The application of water cy-clones dates back approximately ten years, following its development at the Dutch State Mines. ( 3) A number of papers published d

Jan 1, 1961

By William Campbell

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetitions of foot-notes, references to authorities are made in the paper by means of figures, referring to a numbered list in the appendix.-J. S.] I. INTRODUCTION. IN the olden days the making of alloys was au art, and the secrets of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formula are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,1 Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville 7 on the Cu-Sn series and of Shepherd 8 on the * Associate Professor of Metallurgy, Columbia University in the City of New York.

Dec 1, 1912

By D. S. Bubar

This presentation will represent a diversion from the central theme of Cordilleran geology, in both time and space, as we move 2,000 miles east of Spokane to eastern Canada, specifically the province of Quebec, to discuss a major new Archean-age volcanogenic massive sulphide deposit called Louvicourt. The deposit is located in the Val d'Or camp in the prolific Abitibi Greenstone Belt some 400 miles north of Montreal. It was discovered by Aur Resources in June, 1989 on a property operated under the terms of a joint venture with Louvem Mining, a Quebec company controlled by Ste. Genevieve Resources Inc. of Montreal. As a geologist, I am proud to be able to describe Louvicourt as a geological discovery, as it was found by doing systematic deep diamond drilling based on a geological concept. The deposit is essentially blind from surface and lay undiscovered for the 10 years that the Louvem mine was in production just 2,000 feet away from its easternmost workings.

Jan 1, 1991

By E L. Kotova

Completeness of extraction of a mineral from ore depends on many reasons. First of all it is a function of quality of disintegration of ore. It is supposed that two basic factors: character of structure and texture of the ore aggregate and a disintegration technique influence the quality of the mineral aggregate destruction, æopeningÆ of its internal boundaries. In this paper, the problem of technological mineralogy from the point of view of genesis of the mineral aggregate, its typomorphical features and methods of their quantitative description are discussed. The purpose of this research is to provide information for technologists. It should enable the development of a rational flexible scheme of disintegration of ore with full extraction of a useful component, without its losses and without unnecessary expenses of energy. For achievement of this purpose the mineralogical information should have ½number and a measure+. By the authors, the technique of the quantitative analysis of fabric of the mineral aggregate based on several models û thermodynamic, crystallographic and geometrical is offered and discussed. The leading role in the quantitative analysis of a fabric of ore belongs to internal bounders. But internal bounders of the mineral aggregate by bounders or faces of the mineral individuals or mineral grains are formed. Their geometry, orientation concerning own (mineral grain) crystallographic lattices, orientation and distribution in space of the ore aggregate are proportional to the energy accumulated at origin and the further growth. These characteristics of mineral individuals are consequences of conditions of their formation. That is why the named triad of models is used. From crystallography it is known that faces of different stability and mobility form borders of crystals. They also contain different quantity of energy. Mineral grains also are faceted by different energy borders. They form intergrowths with each other according to a principle of balance or unbalance. That is why in addition to traditional parameters of the description of a fabric of the mineral aggregate (mode and grainmetrical composition) it is necessary to add new. For example, length and the square of intergrowthing bounders of mineral individuals differentiated (in couples), crystallographic symbols of borders, their roughness and so forth. Consequently, solving a problem of the geometrical characteristic of borders, we define also its power characteristic. In this paper experience of application of our technology in studying ores of one of deposits of Urals Mountains is presented. For realisation of these types of the analysis technologies of measurement, the program of calculation and the devices, which are carrying out the analysis in a semi-automatic mode, are possessed. Structure and texture of rock or ore aggregate reflect its formation and transformation conditions. It is important to understand that disintegration energy cannot be more than aggregation energy, the energy of intergrowths formation. The square and orientation of mineral individuals borders vary at pressures or stresses of mineral aggregate evolution. These phenomena often cause selective increase in the square of borders at constant average grain size, ie the granulation. Granulation presents the increase in quantity of mineral individuals while their modal share remains constant. At the same time their average mineral grains size. Some mineral individuals increase in size at increased pressure. When lithostatic or lateral pressure drops the majority of mineral grains increases in volume at the cost of intersticial or film solutions or fine grains. These are only special examples of the ontogenesis of the mineral aggregate. They illustrate our statement that all changes in fabric of the mineral aggregate are a reaction on varying external (ie geological) conditions. It is possible to consider that structurisation of totality of mineral individuals as a whole is a process of adaptation of the mineral aggregate, which forms and exists in varying force and energy fields. Differential and integrated geometry of total internal boundaries of the mineral aggregate serves as adaptation mechanism of the mineral grains system. Boundaries form intergrowths of the mineral aggregate. Thus, it is possible to consider that the most informative parameters of the stereometric analysis for restoration of the ontogenesis of the mineral aggregate are the following. First of all, it is a quantitative estimation of the volumetric shape of the ore mineral in crystallographic coordinates, a total area of borders of all mineral grains in the aggregate, the specific square of their boundaries, the specific square of intergrowth boundaries of the ore mineral separately with grains of each minerals of the matrix of the mineral aggregate as well as traditional grainsmetric and modal composition. For realisation of these types of the analysis technologies of measurement, the program of calculation and the devices that are carrying out the analysis in a semi-automatic mode are possessed.

Jan 1, 2008

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010