Search Documents

By R. C. Himes, K. Zanio, J. B. Wagner, J. W. Moody, J. F. Miller, W. Johnson

The recent research with which this paper deals has been concerned with the preparation of pure PbTe crystals suitable for control of radiative processes and othe.v electronic applications. The research has been directed toward the developrnent of methods for the preparation of puve, homogeneous, loul-ca,wier-density PbTe crystals suitable for use in the fabrication of optically pumped and electrically pumped diode lasers. Steps in the preparation of the crystals include 1) purification of the starting materials, 2) synthesis and purification of the PbTe, 3) growoth of PbTe crystals, and 4) adjustt~zertt of composition of the crystals This Paper describes the general preparation procedure employed and discusses some investigntiotzs of purification processes. THE as-received lead and tellurium are nominally 99.999 to 99.9999 pct pure. Assays furnished by the suppliers, obtained by emission spectrographic analysis, show only the presence of about 2 ppm Mg in the tellurium. Such analyses are not very informative, however, since they give no information on the concentrations of normally gaseous impurity elements such as oxygen. Both the lead and the tellurium in the as-received state usually contain appreciable concentrations of oxygen—primarily in the form of oxides on the surfaces of the material. To reduce the oxygen content, the lead is held in the molten state in hydrogen at -700°C for several hours. For this treatment, the lead is contained in a graphite boat which is rf-heated, and the hydrogen is passed through a liquid-nitrogen trap prior to use. Tellurium is subjected to multiple distillation in hydrogen to remove oxygen and other foreign impurities. If, in conducting the distillation, approximately the last 10 pct of the charge at each "stage" is left as the discard cut, purification of the tellurium proceeds as indicated in Fig. 1.l Tellurium used in this work has been distilled two or three times to reduce carrier concentration to about 10" per cu cm. The PbTe is prepared from the purified elements by reacting them in the molten state in sealed, evacuated, or hydrogen-filled silica ampoules. The charge is usually held above the melting point of PbTe (923°C) at 1000 C for 24 hr to ensure that it has been homogenized. Two methods have been employed for the growth of the required single crystals of PbTe: growth from the melt, which will be discussed first, and growth from the vapor phase. Large single crystals of p-type PbTe can be grown readily from the melt by the Bridgman method. For this method of crystal growth, the PbTe is synthesized in situ from proper proportions of the purified elements. Growth (dropping) rates in the range 1.3 to 6.5 mm per hr are employed. Material near the maximum melting composition (about 50.012 at. pct Te) is utilized to avoid composition change on freezing, and thus to obtain crystals of nearly uniform composition. Crystals prepared by use of procedures described up to this point were sufficiently pure and perfect that they could be used for the preparation of laser crystals in studies at Lincoln Laboratory.2-5 ADJUSTMENT OF COMPOSITION Good n-type crystals of PbTe cannot readily be grown from the melt. Further, growth from the melt of crystals of any compositions (n or p type) other than those near the maximum melting composition is difficult because of the large composition changes that must occur on freezing.'" However, melt-grown crystals can rapidly be brought to other desired compositions by isothermal equilibration through the vapor phase with a two-phase Pb-Te stock material, essentially as described by Brebrick and Allgaier.1 The work to be discussed has been concerned with the preparation of n-type crystals; thus, the two-phase stock which was employed contained excess lead, and all ensuing discussion is of the preparation and properties of n-type crystals. The equilibration was designed to the shift composition to the lead-rich limit of stability at the selected temperature. Initial treatment of the crystals at high temperature was employed to minimize the total time required for the equilibration. Final adjustments of the composition and state of the crystals were made by use of low-temperature heat treatment at temperatures in the range 200" to

Jan 1, 1968

By H. G. Papacek

The Fabrica Mine of the Brazilian iron ore company Ferteco mines on an extremely inhomogenous ore deposit. A large amount of the crude ore consists of fines minus 100 micron which cannot be sold without further treatment because of its chemical and physical properties. In order to make full use of the mined crude ore an expansion program has been realized which incorporates among others a concentrator to produce classified blast furnace ore , sinter feed and pellet feed. The pellet feed is converted in a 2.5 million tons per year Lurgi Dravo plant into high grade pellets. The paper discusses the selection of the concentration process, the pelletizing process and describes the experiences with the operation plant during the startup and the first years of operation.

Jan 1, 1979

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By P M. Hetherington, M P. Murphy, K E. Crook, F Pym

Resource characterisation is critical for informed decisions in both strategic and operational space. The sources of information for resource characterisation are limited by: direct measurement of resource attributes, such as grades, rock-types, mineralogy, and are available only from sparse locations, ie drill holes; or indirect geophysical measurements such as seismic, gravity or electro[1]magnetic survey. Data collection tools, methods, and processing technologies are constantly improving providing a broad spectrum of options for data collection strategies. The cost of each data survey varies from thousands to millions of dollars with the value of each additional data having diminishing return for a particular business decision. The value of information analysis provides the optimal decision on data collection strategy within a limited available budget. This work presents an example of value of information analysis for new Blast Hole Assay Tool (BHAT) and Reverse Circulation Grade Control (RCGC) data used in addition to the wider spaced exploration data. The value of information is quantified in terms of reduction of grade uncertainty, ore loss and dilution by comparing different combinations of data collection methods. Four different strategies were considered: exploration samples in addition to 50 per cent of blastholes surveyed with BHAT, exploration samples in addition to 33 per cent of blastholes surveyed with BHAT, exploration with wide-spaced RCGC data, and exploration without additional grade control. For each strategy the observed values have been simulated using advanced multivariate geostatistical simulations and compared with simulated ground truth models. The calculated uncertainty, ore loss and dilution informed the optimal data collection strategy. Opportunity to reduce sample density from the nominal 50 per cent of drill holes was evaluated.

Mar 22, 2022

By Ho-Sang Sohn

The kinetic study on desulfurization of copper matte by gas bubbling was designed under the presumptions of lower FeO activity and of no slag formation, Copper matte with 59% Cu and 22.6% S in weight was oxidized at 1523K by bubbling of Ar + O2 gas through a submerged nozzle. The effects of oxygen partial pressure and flow rate of gas on the oxidation rate of matte were discussed. The desulfurization rate and the evolution rate of SO2 gas of copper matte were significantly influenced by the oxygen partial pressure, but the dependence on gas flow rate was rather complicated. The desulfurization rate and evolution rate of SO2 gas of copper matte were described by the mass transfer rate through the gas film around the rising gas bubbles. Thermodynamic correlation equations between the partial pressure of gaseous species and matte composition were incorporated to the kinetic calculation, The present model shows that the reaction path starts to transiently cross over an isobar line of PSO2 to asymptotically approach to the particular isobar line drawn in a matte composition plane of %S and %O.

Jan 1, 2003

Gary R. Steele is vice president, corporate marketing with Energy Fuels Resources. As such, he knows the global uranium market. The following are some of his thoughts on uranium?s place in the global energy picture. ME: What are Energy Fuels Resources? thoughts on the global nuclear power industry? Steele: The global nuclear power industry is a major contributor to the electrical needs of the world. Though generation by nuclear reactors has primarily attracted attention through the reactor accidents at Three Mile Island and Chernobyl, nuclear power continues to quietly and safely provide power to a growing and power-hungry world population. As of March 2008, 30 countries were operating 439 nuclear power reactors. Nuclear power plants provided about 15 percent of the world?s electricity production in 2007. France leads the world in nuclear utilization, with 77 percent of its power coming from nuclear plants. And Lithuania, Slovakia and Belgium each derive more than 50 percent of their power needs from nuclear plants. For much of the developed world, nuclear generation has already been contributing significantly to the supply of electricity. Additionally, 34 new nuclear plants are under construction in 14 countries. Leading the rush to build new nuclear generating plants are China, Russia and India. Each of these countries is building six new nuclear power plants. These 18 plants, totaling almost 12,000 MW of generation capacity, will require about 7.25 kt (16 million lbs) of U3O8 for their initial fuel load and will consume about 2.45 kt/a (5.4 million lbs/year) for the rest of their operating lives. The rest of the world, outside of the United States, has used nuclear power as a viable and economic generation alternative since the commercialization of utility nuclear reactors. And current activity supports the strong future of the nuclear alternative internationally.

Jan 1, 2008

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Pre-reduction of chromite outside the submerged-arc furnace (SAF) can significantly lower the specific power consumption in the SAF process. Conventional processes for the pre-reduction of the ore operate at relatively high temperatures, at 1400-1500°C. It is possible to enhance the rate of reduction at low temperatures by optimizing the flow rate of inert gas over the reaction site. The influence of the flow rate of inert gas on the rate of reduction of chromite ore was investigated. The rate of reduction initially decreased wit the flow rate of the gas. It increased subsequently at higher flow rates to be followed by a decrease again. There was an optimum flow rate at which maximum reduction could be obtained. It was possible to achieve high levels of reduction at 1200°C by optimising the flow rate of the gas. The degree of reduction obtained was comparable to that obtained at 1400-1500°C, by conventional process routes.

Jan 1, 2007

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By J. E. Bevan

Once mining compromises the stability of a rock mass, the dangerous task of roof bolting begins. Many attempts have been made to automate this process, but there are still many refinements that need to be made. In the past, roof bolting modules were designed around the abilities of a human operator. Currently, researchers are taking a new approach that focuses on designing modules that can utilize bolting methods that are easily automated. A non-rotating anchor that is locked into position by a linear force (as opposed to a rotational force) was designed by researchers at the U.S. Bureau of Mines. Once the bolt is secured in the bolt-hole by the anchor, the bolt is tensioned and a collet is used to secure the other end of the bolt. This process replaces the traditional bolt-nut fastening method. This program is part of an effort at the U.S. Bureau of Mines to automate the coal mining process.

Jan 1, 1994

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

By C. Eddine

"Can we use data to make communication effective? How does one successfully tackle the challenge of solving cultural differences and harmonizing the needs of diverse stakeholders while developing and maintaining a strong and reliable corporate image? Is it possible to achieve better engagement and minimizing risks with data? This paper aims to explore human rights and business procedures, the promotion of shared prosperity in a sustainable manner and the use of metrics to guide decision-making process. Among the topics examined are: • the significance of stakeholder engagement in community development projects; • the use of grievance mechanisms to give a voice to First Nations and communities / populations in vulnerable positions (including children and elders); • the benefits of configuring and implementing a feedback system in partnership with the communities. This research is a preliminary initiative and has limitations on the extent of the material used. The author acknowledges there is a vast amount of work and publications available on this subject, as well, as a variety of examples that have not been included. The intention is to keep developing this research to assess and expand how data can be used to minimize risks and improve engagement, in addition to inspire others to continue advancing this topic. Natural resources consumption is a reality that will not disappear in a foreseeable future. Several developments and operations are located in remote areas where communities in vulnerable situation and Indigenous Peoples live. Feedback systems are being ratified as a tool to help tackling the challenges of harmonizing cultural differences and fulfilling the needs of diverse stakeholders. Integrating social, environmental, and economic values plays an imperative purpose in preserving a productive and trustworthy relationship with stakeholders. Positioning social standards next to environmental and economic principles shows inclusiveness and firm intention of integration. We add value to a positive image of our industry by embracing responsibility for corporate actions and promoting their beneficial impact on the environment. The social context within communities, groups and organizations is dynamic and presents new challenges as connections evolve. There are wildly diverse expectations which one may need to address during exploration, construction and operating phases. Disagreements are an inevitable consequence of interactions due to the different needs and requirements of the parts involved. Nevertheless, balancing differences and solving conflicts can offer remarkable opportunities for improvement."

Jan 1, 2016

By K. I. Savage, L. G. Austin, S. C. Sun

The comminution environment - the physical, chemical, and solid state - was studied for silicon carbide ground wet in a laboratory vibratory mill. The relative importance of these variables on the grinding rate of producing a material 50% passing 5µ from a powder feed of 50% passing 19µ was established.

Jan 1, 1975

By Daniel C. Boteler

Five lignites from the northern Great Plains province were carbonized at temperatures from 500° to 1,000° C in a bench-scale unit. A replicated Greco-Latin square experimental design was employed to allow testing of four independent variables at five levels. Independent variables investigated were temperature, source of lignite (mine), weight of charge, and moisture content of charge. Dependent variables were char yield, tar yield, light-oil yield, tar plus light-oil yield, carbonization gas yield, and carbonization gas heat yield. An analysis of variance indicated that, at the 99-percent confidence level, the independent variables of carbonization temperature, source of lignite, and weight of charge were significant for yields of char, tar plus light oil, and carbonization gas, whereas moisture content was only significant for carbonization gas yields. At the 95-percent confidence level, moisture content significantly influenced the carbonization gas heat yield per pound of lignite charge and the yields of dry tar plus light oil. All dependent variables were determined on a moisture- and ash-free basis. Multiple regression equations for predicting seven different factors of carbonization yields as functions of carbonization temperature and initial composition were developed using computer techniques. Equations for yields of char, tar plus light oil, and carbonization gas were compared with equations previously developed by others at the 500° C level.

Jan 1, 1970

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By Douglas Castleberry

The degree of fragmentation obtained in primary quarry blasting has always been a factor in the speed of digging' the muckpile This paper will discuss a case history of increased production and associated lowered costs from increased fragmentation. The quarry under discussion is fairly new, located in Georgia, and is in the large operation .category. Loading is done by three yard shovels, and, primary crushing by a 48" x 60" haw crusher preceded by a 5' wide feeder. The stone is a hard granite gneiss, of Los Angeles rating 22, and apparent specific gravity is 2.68. The product is shipped to points in that state for railroad ballast, concrete aggregate, and road building stone. Inasmuch as fairly large shovels and a large Jaw were to be utilized, initial drilling and blasting were pointed toward producing fairly large sized muck for this large equipment. This was following a concept somewhat in vogue for some years in the Southeast wherein many large equipment plants would tend towards larger fragmentation, and smaller equipped plants would conversely tend toward attempts at smaller sized rock piles for smaller shovels and crushers.

Jan 1, 1960

By Xu Zhang, Xuewei Lv, Guibao Qiu

Slag foaming phenomenon is of vital importance to the mass and energy transfer in metallurgical processes. A considerable extensively studies carried out via out-gas in the past cannot simulate well the foaming phenomenon formed in the blast furnace where high TiO2 iron ore is used. A gas reaction was designed in the water-glycerol system to simulate the inner-gas system. This study investigated the influences of solution viscosity, particle concentration and particle size on foaming caused by endogenetic gas. The results show that the foaming height decreases with the increase of solution viscosity, which means reduced foaming ability, more difficult foaming elimination process and prolonged time for natural defoaming. With increasing the solid particle content, the foam height presents a trend which increases firstly and then decreases. Under a certain solid particle content, foaming height decreases with the increase of solid particle size, indicating a weak foaming ability.

Jan 1, 2015

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By Z. Sun, H. A. Davies

"Current understanding of the mechanisms by which glassy and crystalline thin ribbons are formed in high speed continuous casting processes is considered. A computer model of the combined heat and momentum transfer during melt spinning has been developed. The influence of roll velocity and of heat transfer coefficient (between the melt and the roll) on the temperature and velocity distributions within the melt puddle is analysed and the thickness of the extracted ribbon computed. The relative importance of heat and momentum transfer under different conditions is assessed and differences between the casting of crystalline and amorphous strip highlighted.IntroductionHigh speed continuous casting of thin metallic ribbon and strip is currently of considerable interest both to metal processers and to those studying process mechanisms. The practical interest arises both from the potential economic benefits to be gained from a shorter and more energy-efficient production route and from the ability to obtain extended and uniform thin strip having a metastable microcrystalline or amorphous structure with enhanced or unique properties. The latter arise from the rapid solidification associated with the cooling of very thin sections of melt brought into intimate thermal contact with one or two rapidly moving heat sinks.The principal processes for casting thin strip include free jet, chill-block melt-spinning (GBMS) (1), melt drag (MD) (2), planar flow casting (PFG) (3) and twin-roll casting (TRG) (4). For the first three of these, all essentially variants of melt-spinning, melt flows through a nozzle onto the circumferential surface of a rapidly rotating roll, whereas for TRG the melt passes into the nip between two contra-rotating rolls. We shall be concerned in this paper with the single-roll melt spinning processes only. For these, a puddle is established where the melt contacts the roll surface and the length of this puddle l is a function of the process conditions, notably the circumferential velocity of the roll Us and the volumetric flow rate of the melt Q. The contact time between any point on the roll surface and this puddle, or residence time eR(= l /Us) determines the thickness of ribbon t extracted from the puddle. This thickness, in turn, partly governs the cooling rate T and the amount of undercooling in the melt and thus the microstructure of the solidified ribbon."

Jan 1, 1986