Search Documents

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By R. H. Marshall, J. Welchner, E. S. Rowland

THIS paper presents results on an exten¬sion into the realm of high-carbon steels of some work recently published' on the effects -of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting harden¬ing of parts in production, the correlation of hardenability information with the [ ] hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd ,2 3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,7 Post and associates' and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however,' into the quantitative variations produced on the hardenability of commercial high¬carbon steels by changes in these factors of time, temperature and prior structure. PROCEDURE A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molyb¬denum-bearing high-carbon steel contain¬ing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. [ ] The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (1650°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (1600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was selected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard. procedure was followed. The effect of time at temperature was examined at intervals of 0, 10 and 40 min. and 4 hr., and a few i6-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By M. Townsend, E. L. Petsonk, H. Abrons, E. Daniloff, K. Kinsley

Workers exposed to certain inhaled dusts may show increased levels of nonspecific airways responsiveness (AR). In some studies, cigarette smokers have also been reported to have increased levels of AR. As part of an ongoing study, we compared the results of preshift methacholine inhalation challenge, spirometry, and smoking and occupational histories, in 191 under-ground bituminous coal miners (M) and 215 non-mining control workers· (C) . All M and c were selected to have normal baseline% predicted FEVI (PPFEV). Mining tenure was recorded as years worked underground (YRUG) and at the coal face (YRFC). AR was assessed as the% decrease in FEVI from baseline divided by the dose of methacholine delivered. M reported similar years smoked (YRSM) but fewer pack-years* (PY) than c~ Overall, both increasing YRSM and PY were associated with more AR*. Smoking C* but not M showed increased AR with increasing PY. In smoking and nonsmoking M, baseline AR and PPFEV showed no association with YRUG. The level of AR was inversely related to YRFC*, possibly representing selection away from dustier jobs. AR was inversely correlated with PPFEV*. In this study, AR and baseline PPFEV were not significantly associated with mining tenure, but cigarette smoking was related to both baseline lung function and level of AR. * p < 0.05 (Supported in part by Grant Gll35142, us Bureau of Mines, Generic Mineral Technology Center for Respirable Dust.)

Jan 1, 1989

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By J. R. Dawson, J. A. Glunt

VESTA No. 4 and 5 mines supply most of the high volatile coal required for Jones & Laughlin&apos;s byproduct coke plants. Until 1944 all coal produced in these mines was loaded by hand. Pressure to mechanize at Vesta was brought on by the manpower shortage in World War 11, and in 1943 a decision was made to change to mechanical loading. It was the opinion of those concerned that by use of selective mining the coal would be clean enough to be processed by the existing preparation plants. At that time coal cleaning at Jones & Laughlin consisted of hand picking the larger sizes at the mine tipples and wet washing at plants located at the Pittsburgh and Aliquippa Works. A typical section of the Pittsburgh seam as it occurs at Vesta is shown in Fig. 1. The 14 to 16 in. of drawslate immediately over the coal is too soft to be used for roof and must be taken down, leaving the rooster coal just above for roof. In selective mining an attempt is made to mine the coal under the drawslate first and then load out the drawslate separately as refuse. In full seam mining slate and coal are shot down at the same time and loaded out. Mechanical loading at Vesta created new problems. It was found that selective mining, even when carefully applied, increased the refuse in the raw coal to such an extent that the washers at the mills were unable to handle it. Large tonnages of refuse were being transported, a reject disposal problem was created, and good metallurgical coal was being loaded out and lost. In addition, the selective method handicapped operation of the loading machines. Fig. 2 shows how the ash content of the raw coal increased as mechanization proceeded at No. 5 mine. New Preparation Plant: After an exhaustive study of this situation by J & L management, is was decided that a preparation plant should be constructed at the mines, capable of handling full seam mined coal and large enough to process full production of both No. 4 and No. 5 mines. It was decided that from the standpoint of inside operation and haulage the new plant should be located as near as possible to the old No. 5 tipple on the Monongahela River near Vestaburg. Full seam mining at Vesta could be expected to produce a tremendous volume of refuse along with the coal, since 14 to 16 in. of slate would be mined with an average 78 in. of coal. Disposal of this refuse required serious consideration in selecting a plant site. The only area near Vestaburg large enough for disposal of the plant refuse was across the Monongahela River at LaBelle. Ample space was available here, and construction at this location would not interfere with operation at the No. 5 tipple. It had been noted over the years that the sulfur content of the coal produced at Vesta was gradually increasing, and there was every indication that this increase could be expected to continue as the mines developed further from the river. It was decided to construct a three-part separation plant with complete blending facilities to produce both metallurgical and steam coal. In this system an attempt is made to reduce the sulfur in the metallurgical coal in a secondary cleaning process. Construction of the new preparation plant got under way early in 1947 and continued until the spring of 1950. The plant was designed to handle 2400 tph of raw coal containing 30 to 35 pct refuse. Cost of outside buildings and equipment was about $14 million. Total cost of the plant, together with improvements and changes made at this time, was approximately $21 million.

Jan 1, 1957

By S. L. May

Tantalum and columbium can be extracted from several of their ores or concentrates by chlorination procedures. Direct chlorination of high-grade minerals in the presence of carbon at temperatures between 500° and 800° C will extract up to 99 percent of the tantalum and columbium. Metallurgical beneficiation of low-grade source materials by carbothermic reduction produces a ferroalloy that is amenable to chlorination at a temperature of 500° C. Over 90 percent of the tantalum and columbium can be recovered.

Jan 1, 1965

Longwall mining originated in the early 18th century in the county of Shropshire in England, where it was known as the longway method. Its name implies the extraction of the seam over a long continuous length or wall of exposed coal. Until the late 19608 and early 1970s the use of the longwall system with a few exceptions was confined to the United Kingdom and Europe. It was not until the early 19708 that the highly productive longwall faces we now know, were developed and the application of the longwall system extended to Australia, South Africa, United states of America and other parts of the world. The modern longwall face has three major components, namely: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the machine to break and load the coal +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the face conveyor; +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; and a system of roof support. &nbsp; This paper reviews the development of longwall mining technology. The parameters directly influencing the production &apos;of a modern longwall face are considered, as are the possible constraints to the further development of the longwall system.

Jan 1, 1991

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993

By Harold E. Heide

The United States is the world&apos;s largest consumer of tin and depends entirely upon foreign imports for its major source of supply. Only a small quantity of tin is produced on the North America continent. The advent of the war in Europe in 1939?brought a threat to our foreign sources of supply, and the Congress took steps to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, and subsequent legislation, the Bureau of&apos; Mines ?and Geological Survey conducted investigations of domestic tin deposits. Most of the tin that has been produced in North America came from the Seward Peninsula, Alaska.

Jan 1, 1948

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

By A. V. Tarasov, V. M. Paretsky

"The knowledge of the true phase composition of the liquid slag is a very important problem, mastering of which grants the possibilities for the scientifically founded choosing of the decoppering method of the autogenous smelting slags. The investigation using different methods of the phase composition of the flash quenched autogenous copper melt's slags has shown, that the most effective method of the slags' decoppering during smelting with the white matte production is the flotation of the recrystallized slags. In this work the authors posed the problem to realize the slags quenching with the rates similar to those, which are used in the modem investigations devoted to the flash quenching of the ironcontaining alloys, with the subsequent study of the quenched samples using the Mossbauer spectroscopy methods in order to establish the connection between the liquid slag's structure and the metals losses with the slag."

Jan 1, 2000

By RAYMOND C. HARTVIKSEN

The Drumbo Mine is located near Highway 401 between Woodstock and Kitchener in southwest Ontario. The tabular flat-lying gypsum bed is between 1.5 to 2.4 m thick and is situated near the base of the Salina Formation, about 116 m below surface. The mine is owned and operated by Westroc Industries Limited. The 3.8 m diameter shaft was drilled using a Hughes CSD 820 drilling rig and a liner sinking technique new to the North American continent. The shaft was completed in the fall of 1977, and remaining facilities were finished in the fall of 1978. Gypsum production started in December 1978, employing the conventional room-and-pillar method of mining.

Jan 1, 1984

By J. L. Eakin

The Bureau of Mines determined agents that are effective in foaming heavy brines and oil from gas wells in severe concentrations of sodium chloride, in severe concentrations of calcium chloride, or in moderate oil-brine mixtures. Dynamic foam tests were designed to select the more effective foaming agents. Numerous foaming agents were tested in concentrated simulated brines, in oilfield brines having varied concentrations of ions, in heavy natural brines, and in a commercial brine generally used as a reservoir pressure-balancing fluid. Several agents were detected that could perform efficiently in the field under the most severe saline conditions. Agents that promote foaming in oil-brine mixtures were also determined.

Jan 1, 1965

By H. D. Jacobs

The Bureau of Mines developed a concentration method to upgrade and utilize marginal natural or direct-shipping iron ores and fine-grained lean iron ores. Presently these ores receive little beneficiation and accordingly have low iron-silica (Fe-Si02) ratios. Ore samples were roasted with equal weights of solid reductant at 1,100° C for 1 hour to metallize the iron and for an additional hour at 1,200° C to promote grain growth. Concentration was effected by crushing and screening techniques and/or wet magnetic separation. Sized concentrates (minus 4 plus 35 mesh) derived from crushing-screening processes contained from 80 to 85 percent iron that was 90 percent metallized. Iron-silica ratios as high as 12:1 and iron recoveries from 75 to 94 percent were obtained. The sized concentrates were judged suitable for use as blast furnace feed. Minus 200-mesh metallized concentrates derived from roasted minus I-inch plus 8-mesh ore fractions and magnetically concentrated contained 90 percent Fe and 4 percent or less Si02, chemically qualifying them as feed for electric furnaces. Roasting minus 8-mesh ore with hydrogen, then magnetically concentrating it, produced iron concentrates containing 57 percent to 67 percent Fe and 3.6 percent to 8.4 percent Si02. The concentrates having Fe-Si02 ratios ranging from 8:1 to 12:1 were considered adequate for use as blast furnace feed. Overall iron recoveries for the 12 ores tested ranged from 56 percent to 94 percent with an average iron recovery of 86 percent.

Jan 1, 1969

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By J. G. Groppo

Laboratory settling and filtration testing was conducted on wet processed fly ash in order to determine the applicability of conventional dewatering techniques to reduce the moisture content prior to drying. Settling tests showed that acceptable clarity (<1.5 g/l suspended solids) could be achieved after as little as 6 minutes of settling. After settling to a consistency of 40 weight % solids, continuous laboratory vacuum filtration testing produced a cake containing below 20% moisture with throughput exceeding 150 lb/ft2/hr.

Jan 1, 1997

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007

By G. W. McCaa

Plans for a large industrial development in the Upper Ohio Valley between Moundsville and New Martinsville, West Virginia, were announced in the Fall of 1955. This development consisted of a large aluminum plant to be .built by Olin-Mathieson; a 675,000 KW power plant to be constructed by the American Electric Power Service; and a large coal mine adjacent to the power plant to be developed by the Hanna Coal Company Division of Consolidation Coal Company. The Ireland Mine was designed to efficiently supply fuel for the power plant, and this was the first consideration in the location of facilities, design, and development of plant and the selection of the equipment. The first problem was to find a suitable area for the surface facilities. A level bottom area south of the power plant was reserved for future industrial plants and this area was also blocked off from the coal reserves by an old abandoned and flooded mine. The coal storage facilities of the power plant were on the north side of the plant and it was decided to locate the coal mine preparation plant on-the shoulder of a hill above the power plant. This location required the excavation of 70,000 yards of rock but permitted the driving of a belt slope from the plant at an angle so that the haulage roads underground would miss the abandoned Cresap Mine. This location also permitted the plant to be located at an elevation so that the conveyors leaving the plant were horizontal and had sufficient clearance above the highway and railroad tracks. The other surface facilities consisting of air shafts, supply slope, supply yard, office, bathhouse, shop and warehouse were located in the valley some distance north of the preparation plant. This location placed these facilities one mile nearer to the working area. Plans for design and development of the mine were started in November 1955; grading and clearing of surface area was started in January 1956; the air shafts and slopes were started in the Spring and Summer of 1956; and the first coal was produced from the supply slope in October 1956. The preparation plant was put in operation in March 1958, and by July 1959 was producing 8,000 tons per day.

Jan 1, 1959

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners&apos; health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker&apos;s cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM&apos;s response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM&apos;s versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner&apos;s average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.