Search Documents

By L. C. Brown, A. J. Stewart

Phase transformations have been studied in Ag-Zn alloys quenched from the high-temperature bcc 0 phase and lying in the composition range 37.4 to 50.0 at. pct Zn. On quenching, the alloy with the lowest zinc content transformed to massive a (fcc); all other alloys formed the ordered (3' phase. On deformation, a martensitic reaction took place forming a close-packed structure. At Lou' zinc contents transformation to this structure was complete. However, above 43 at. pct Zn a p.rogressively increasing amount of ß' was retained following deformation. The close-packed structure was fcc at lower zinc contents (under 47 at. pct Zn) and either hcp or a mixture of fcc and hcp at high zinc concentrations. The structures produced by cold working were unstable and on aging transformed to the ß' phase or the complex hexagonal to phase. For low zinc contents (under 43 at. pct) the fcc st-ructure transformed directly to the equilibrium To phase. With higher zinc contents, some 13' was retained following defownation, and on aging the amount of this phase relative to the close-packed structure increased. On further aging both structures transformed cornpletely to PO. Metallographic examination indicated that the nature of the deformation product depended very markedly on the mode of deformation. Tensile deformation gave a microstructure characteristic of thermal martensite. KING and Massalski1 have shown that an alloy of Ag-50 at. pct Zn quenched from the high-temperature bcc ß phase undergoes a low-temperature ordering reaction forming ß' which can be retained to room temperature. On deformation an hcp phase is produced, although this is unstable and the structure reverts completely to ß' on aging. In the present paper, the work of King and Massalski is extended to cover a wide composition range in the p phase, observations being made of the structure of the quenched 13 and of the effects of deformation and aging. The relevant portion of the Ag-Zn phase diagram is shown in Fig. 1. King and Massalski have shown that close to stoichiometry the ß' phase is the equilibrium structure at low temperatures. The approximate composition range of this phase, taken from a recent paper by Pops and Massalski,3 is shown on the phase diagram. The locations of atom sites are very similar in the ß' and to structures, and the 4, structure can be derived from the 0' structure by a small movement of atoms mainly in the direction of the cube diagonal.4'5 However, the probability of filling any particular atom site by a silver or a zinc atom is markedly different in the two structures. The structure can be considered partly ordered but the arrangement of the ordered atoms is completely different from that in the p' structure and transformation from ß' to requires a large fraction of the atoms to change position. It has been shown that the ß' transformation is thermally activated involving normal nucleation and growth processes.5,8 Massalski and Barrett7 have shown that in the Cu-Zn binary the (3 phase can be retained in the ordered state to room temperature over a wide composition range. On deformation a new close-packed phase is produced, the structure varying from fcc to a mixture of fcc + hcp to hcp alone with increasing zinc concentration. It appears that an ordering reaction is necessary to retain the bcc phase to room temperature. In CU-Ga,8 the bcc phase cannot be retained to low temperatures as it transforms by a massive reaction above the ordering temperature of the ß phase. The structure of the massive phase is very similar to that in Cu-Zn, varying from fcc to fcc + hcp to hcp with increasing zinc concentration. Similar structures have also been observed in CU-A1,9 Ag-Cd,10,11 and Ag-Al.12 EXPERIMENTAL The alloys were prepared by melting fine silver (99.99 pct purity) and electrolytic zinc (99.999 pct

Jan 1, 1969

By Lassaad Hazzar

The ultimate lateral resistance of piles in cohesive soil is studied using the well-known finite difference code, FLAC2D. The Modified Cam Clay (MCC) constitutive relation is adopted in the analyses to model the cohesive soil behavior, whereas the structural pile model with three degree of freedoms, available in FLAC2D library, is adopted to model the piles. The reliability of Broms's method, still used in the current design practice of piles under lateral loads, is verified. Comparisons between the ultimate lateral resistances of piles and those deduced from the graphs proposed by Broms (1964) are presented in graphs. Different factors thought to affect the lateral resistance of piles in cohesive soil, not adequately considered in Broms's method, such as clay stiffness, pile length, pile diameter and axial load are parametrically studied. A special concern is devoted to elucidate the effects of over-consolidation ratio (OCR) on the ultimate lateral resistance of piles in cohesive soil.

Aug 1, 2013

By Steve Kral

Worker safety is an issue that transcends industries, whether it be mining, construction, manufacturing or even general office work. In the mining industry, safety and training are particularly important because mining is a dangerous occupation. Throughout the years, federal and state safety regulations have been written and revised to keep up with the changing technologies. And mine operators have installed their own safety and training programs. They have come to realize that a safe and healthy workforce has positive effects on productivity and profitability —not to mention avoiding the high costs of injury-related absenteeism.

Jan 1, 2003

By B. Rourke, O&apos

Copper Refineries Ltd. (CRL), Townsville is Australia's largest producer and exporter of refined copper cathode. This status has been maintained by the implementation of a significant capital works program that increased the production capacity to 270,000 t/y by June 1999. In 1979, CRL was the first in the world to commission the ISA Process Technology which has now been marketed to 47 licensees worldwide. The new tankhouse design has focused particular attention on customer requirements, operational improvements, materials handling and equipment modernisation. Equipment which has been upgraded includes cranes, anode preparation, cathode stripping and scrap washing machines along with the total replacement of the electrolyte and electrical reticulation systems. Side stream electrolyte filtration has been introduced. Improvements to electrode alignment afforded by the conversion to polymer concrete cells, precise electrode location, and the upgrade of the electrode handling machines will ensure that CRL. continues to be one of the world's major quality copper cathode producers.

Jan 1, 1999

One of the best known of the early mining districts of Nevada was that at Eureka, where gold was first produced in 1864. While the most productive period for the district was during the early 1900s, production was maintained until World War II. During this time it is said that the Eureka district produced as much as $200 million from over 3,200 km (2,000 miles) of tunnels and workings. The Windfall Mine was discovered in 1902; and a 100 ton cyanide plant was operated there during the periods 1907 to 1912 and 1932 to 1940. Since 1974, however, Windfall Venture has been operating a unique heap leaching facility on the site of the old Windfall Mine. Gold at the Windfall occurs primarily in the Cambrian Hamburg dolomite which has been "sanded" and in which the original cementing material has been destroyed. The gold is micron sized and is accompanied by anomalous amounts of arsenic and mercury; however, the ore is low in base metals which distinguishes it from the typical Eureka district ores. Mining the ore causes it to break down into very fine sizes, approximately 50% minus 150 microns (100 mesh). Conventional heap leaching by spraying proved to be impossible; and extensive test work on alternate methods, aided by the United States Bureau of Mines, was conducted using 9 m (30 ft) high columns and then large tonnage heaps. The leaching procedure adopted was to build 10.6 m (35 ft) high heaps on a 50 mm (2 in.) asphalt pad covered with a layer of gravel for drainage assisted by perforated pipe drains and gravel-packed sumps. A berm is constructed around the top of each pad and cyanide solution is allowed to “pond” on top of the heap. The resulting percolation is at the rate of 24 liters per sq m per hr (0.6 gal per sq ft per hr), a figure about 2.4 times the average used in other heap leaching operations. The dolomite furnishes its own protective alkalinity and no lime or caustic is used in the solution which contains 0.4 kg per mt (0.8 lb per st) of NaCN. Pregnant solution from the heaps averages about 0.7 g Au per mt (0.02 oz per st) with a cyanide content of about 0. 2 kg per mt (0.4 lb per st) and a pH of plus 9. Addition of NaCN brings the pH of the leach solution up to 11 to 12. Carbon adsorption of the gold was originally done in six enclosed columns mounted in a trailer but five conventional columns have been substituted as the size of the operations has increased. Carbon stripping is with hot caustic, cyanide and 10% ethanol solution. The

Jan 1, 1981

By Long Meng, Kuiyuan Chen, Zhe Wang, Yiwei Zhong, Zhancheng Guo

Printed circuit boards (PCBs) contain plenty of toxic substances as well as valuable metals (e.g. Pb and Sn). In this study, supergravity as a novel technology was used to separate and recover different mass ratios (Pb/Sn) of Pb-Sn alloys from PCBs. In a supergravity field, liquid metal phase can permeate from the solid particles, and based on this, 200, 280 and 400 °C were selected to separate Pb and Sn from PCBs. The results showed that the gravity coefficient only affected the Pb-Sn alloy weight, and did not change the mass ratio of Pb/Sn. With the increase of gravity coefficient, the recovery values of Pb and Sn were increased. In the separation process, under the gravity coefficient of 1000 and separation time of 2 min, the recovery values of Pb were 33.13, 38.86 and 50.48% at the temperature of 200, 280 and 400 °C, respectively, and the recovery values of Sn were 23.31, 32.57, and 40.81%, respectively, and the mass ratios of Pb/Sn in the Pb-Sn alloys were 0.55, 0.40 and 0.64, respectively. This provided a new approach to recycle Pb and Sn from PCBs.

Mar 1, 2018

By Dr. -Ing. Karlheinz Timtner

This paper deals with the complicated and often misunderstood relationship between torsional windup, load sharing and peak torques in conveyor backstops. The principals apply in low speed, intermediate speed or high speed applications. Once the controlling factors are understood, a reasonable approach to selection procedures can be achieved.

Jan 1, 1996

By V. S. Tadsen

Today, man is able to probe space because of technological advancements including the ability to control certain combustion reactions very precisely. The recent adjustment of the attitude of Skylab by radio command from earth is an excellent example of such control. It is strange, and indeed unfortunate, that very little is known about the mechanism of combustion of pulverized coal, the primary fuel for rotary kilns. The selection of a coal for direct pulverized firing of a rotary lime kiln may be determined by trial and error, persistence of sales personnel, proximate analyses, grindability, or apparent BTU cost. Occasionally, the only question asked is, "How much lime will it make?" To study the behavior of a particle of coal in the combustion stream of a rotary kiln is most difficult. We must, therefore, discuss the general mechanism of combustion of pulverized coal, and relate this mechanism to the selection of a proper coal for a rotary kiln. The classic three T's -time, temperature, turbulence -must be enlarged upon for a better understanding of the problem. Pulverized coal occupies only 0.01 per cent of the volume of air required for its combustion. This mixture behaves like a gas and the general laws governing the movement of solid particles in gasses are in effect. The differential velocity between air and coal particles depends on forced and natural convection, diffusion, and the length of time each particle is in the combustion space. As a particle of coal absorbs heat from its surroundings, it begins to give off volatiles". These gasses ignite as their kindling temperature is reached, and burn readily because of the excess oxygen immediately available. Combustion proceeds at this stage by the outward diffusion of gas from the coal particle into the surrounding oxygen-rich envelope. We could say combustion at this stage represents a small coal particle surrounded by an envelope of volatiles burning at their point of contact with sufficient oxygen. This release or expulsion of gasses from the coal may result in exfoliation or disintegration of the coal particle. If this occurs, and it is desirable that it should, it will accelerate the final stages of combustion. The escape of volatile material from the particle of coal and its subsequent combustion will cause increased turbulence around that individual particle. Ignition is maintained by radiation from gasses and solids in the combustion system, and most importantly, re-radiation from the kiln refractories and the process load.

Jan 1, 1978

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier's Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

By Guido Del Giudice

THE term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(1)? Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince; 3 Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) OLD THEORY OF SLIME-COATINGS At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and, on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince's experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed.

Jan 1, 1934

By R. T. Hukki

THE accepted basis of comparisons between mills of different diameter is the percentage critical speed. If n = actual mill speed, rpm, nc = calculated critical speed, rpm, np = calculated percentage critical speed, and D == inside diameter of the mill in feet, then n, In the following analysis capacity, T, is expressed in short tons per hour, tph, and power consumption, P, in kilowatts, kw. Accordingly power consumption per unit of capacity, P will be expressed in kilowatt hours per short ton, or kw-hr per ton. In all equations D refers to the inside diameter of the mill in feet and v to the peripheral speed of the mill in feet per minute inside the liners. ' Comparison between separate mills must be based on equivalent grinding conditions, i.e., same feed, same size distribution of feed, same size distribution of product, and same percentage of solids. In addition, comparisons between separate rod mills must be based on the same rods, same type of liners, and same percentage rod load. Comparisons between separate ball mills presuppose the same balls, similar liners, and same relative ball load. The practical np-range through which the equations apply varies, being narrower for fine grinding in ball mills and wider for coarse crushing in rod mills. The Relationship between Capacity and Speed It is the general belief that the capacity, T, of a tumbling mill is directly proportional to the speed of the mill, other things remaining constant.' Mathematically this is represented by the equation T - c¹ n tph [4] where c, is a factor related with the grinding characteristics of the ore, method of reduction, and the units chosen. It is proposed here that the general equation relating mill capacity and speed should be of the form T = c¹ nm tph [5] In other words, the capacity should be proportional to the mill speed raised to power m, the numerical value of the exponent being 1 5 m 5 1.5, depending on the circumstances. Eq. 5 can also be written in the following forms: T = c, (np)m tph, and [6] T=Ca vm tph, [71 where v = peripheral speed of the mill in feet per minute. If the observed capacity of a mill at speed n¹ is = T¹ tph, the capacity T² of the same mill at speed n² should be T² = T¹ (n²/n¹)tph [8] The Relationship between Power Consumption, Mill Diameter, and Speed The only well known theoretical deduction relating power consumption, P, and mill diameter appears to be the formula of duPont introduced by Gow, Guggenheim, Campbell, and Coghill.' According to duPont, the power required to operate a mill is a function of the mass of the balls, of the lever arm of the ball mass, and of the speed of the mill. The ball mass per unit of mill length is proportional to the square of the diameter, the lever arm is directly proportional to the diameter, and the critical mill speed or any percentage thereof is inversely proportional to the square root of the mill diameter. Following this reasoning, the original duPont formula is of the form P = c4D² c D • c6D-0.5 = c7D2.5 [9] If the mill speed in the above equation is expressed in terms of Eq. 3, the duPont formula may be written as follows: P=f1(D2) f2(D) f³(—np) or [10] vD P = c np D2.5 kw [11] Eq. 11 may also be derived from the mechanical principle of force, which is equal to mass x acceleration. Power necessary to operate a mill may be considered to be an homogeneous linear function of the force developed. Ball or rod mass per unit of mill length is a function of D2. The acceleration factor of the ball or rod mass is a function of the peripheral speed of the mill. Thus P = f4(F) = /x(D2) f5(v) Indicating that v = nDn, and n = c9 np /vD, the above equation becomes P = f2 (D2) -fa (D ca np/vD

Jan 1, 1955

By Graeme J. Jameson

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about one metre (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash-water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1988

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By Ángel Ruiz-Sánchez

Ethylene glycol additions to aqueous acid solutions for leaching copper sulfides increase both copper and iron extractions compared to a conventional sulfuric acid leach with hydrogen peroxide (H2O2). The role of ethylene glycol is to prevent peroxide destruction, which normally occurs in solutions that contain both cupric and ferric ions. However, despite this improvement, ethylene glycol and sulfuric acid concentrations must be high (3.5 M and 0.7 M, respectively) to obtain satisfactory conversion levels at room temperature. In the present investigation, EDTA was used as an additive to complex the cupric and ferrous ions, lowering the requirements of ethylene glycol and H2SO4 to 0.11 M and 0.007 M, respectively, while minimizing oxidant decomposition. The experimental results for a mainly chalcopyrite, copper concentrate showed complete copper extraction in 24 h at room temperature, with the stoichiometric quantity of EDTA for the copper and iron dissolved. Tests using seawater were equally as successful.

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By Mitchell Gordon

"In almost all thickener applications the highest possible solid/liquid separation efficiency is what is desired by the user. There is a trend in the industry due to monetary restraints and environmental pressures to look at ways to extract this maximum performance by either retrofitting existing thickeners or installing the most cost effective new thickener. This paper looks at some of the common problem areas and presents a range of solutions developed by Outokumpu Mintec in North America and outokumpu's subsidiary Supaflo Technologies Pty. Ltd.The Emerging PictureAfter many hours of discussions with a large number of plant personnel over the last two years a picture began to emerge regarding current thickening operations in the industry. Initially, it seemed that everybody had their own unique process problems and therefore needed a correspondingly unique solution. Looking more closely at all the cases and the ideas that we had either implemented or suggested, it gradually became apparent that the majority of operators all had one and the same process need ....""Better Separation Efficiency""The range of operational problems that were uncovered in the survey were much more varied than expected and often were not even considered initially to be thickener problems. Often, it was only after the rejection of many solutions to the problem, generally due to capital cost, that the actual cause of the problem was looked at and found to be a thick-ener.A summary of the problems that have so far been identified is presented in Table 1. They are subdivided under three major categories of environmental, process and paste fill to highlight the wide range of mining activities that can be affected by poor thickener performance. These seem to be the major areas where the need for better separation efficiency is rooted."

Jan 1, 1995

By August J. Breitenstein, W. Spencer Hutchinson

The outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations are shown for the years 1900, 1930 and 1950 in Table 1. Method or Preparation and Interpretation of Statistical Data The fuels comprised in this study are: (1) the coal group including both bituminous and anthracite coal; (2) the petroleum group, taking in not only petroleum but natural gas and natural-gas gasoline. Natural gas for many years has been used in localities relatively near the wells but statistics were found no earlier than 1910. Demand has rapidly

Jan 1, 1934

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963

Dear Fred: Bobby Schultz sent me the attached copy of the 1926 Proceedings owe Rocky Mountain Coal Mining Institute which he borrowed from you after I had requested to get the volume containing a paper of mine on the hazards of electricity. I am returning it direct to you as requested by Bob. [ ] Thanks much to both of you. Very truly yours, [ ] D. HARRINGTON, Chief, Health and Safety Branch.

Jan 1, 1926